DeWalt AP400 Unpacking and Cleaning, Assembly Tools Required, Assembly Time Estimate, Casters

Page 9

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol.

Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine.

After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

ASSEMBLY

For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual.

ASSEMBLY TOOLS REQUIRED

1/2” and 9/16” Wrench, Open-End or Socket

ASSEMBLY TIME ESTIMATE

Assembly for this machine takes approximately 1-2 hours.

CASTERS

1.Locate the bag of hardware with the four 3/8 hex nuts and four 3/8 lockwashers for the four casters.

2.For each wheel, insert bolt from caster through the holes (A) Fig. 3 in the base of the dust collector (three are not shown).

A

3. Place a 3/8 lockwasher (A) Fig. 4 onto each bolt.

Fig. 3

4.Thread 3/8 hex nut (B) Fig. 4 onto each of the four bolts and tighten securely.

B

A

Fig. 4

9

Image 9

Contents Contractors Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsStay ALERT, Watch What YOU are Doing General Safety RulesRefer to them often Use them to instruct others Additional Specific Safety RulesPower Connections Motor SpecificationsGrounding Instructions Extension Cords Volt Single Phase OperationFunctional Description Carton ContentsUnpacking and Cleaning AssemblyAssembly Tools Required Assembly Time EstimateSide Supports Attaching Motor and Blower Assembly to FrameAttached to the Side Supports Closest to the Motor SupportFilter and Dust Collection Bags to Drum Locking Switch in OFF Position Dust Intake Hose to Motor Blower AssemblyOperation Starting and Stopping Dust CollectorService Troubleshooting MaintenanceAccessories WarrantyFrançais LES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsLA Proposition DE Californie Lutilisation DE CET Outil Règles DE Sécurité GénéralesConserver CES Directives Règles DE Sécurité Spécifiques SupplémentairesRaccordements Électriques Spécifications DU MoteurInstructions DE Mise À LA Terre Fonctionnement Monophasé À 240 Volts Cordon DE RallongeDescription Fonctionnelle Contenus DE BoiteAVANT-PROPOS Assemblage Plaque DE Support Fixation DU Module MOTEUR- Souffleur SUR LE BâtiInsérer une vis à tête hexagonale de 5/16-18x3/4 po Fixation DU Tuyau D’ADMISSION AU Module MOTEUR-SOUFFLEUR FonctionnementDémarrage ET Arrêt DE L’OUTIL Verrouiller L’INTERRUPTEUR EN Position D’ARRÊTAccessoiries Depannage EntretienGarantie Español Instrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESProposición DE California Normas Generales DE Seguridad Guarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadConexiones a LA Fuente DE Alimentación Especificaciones DEL MotorInstrucciones DE Conexión a Tierra Cordón DE Extensión DE Calibre Mínimo Cordones DE ExtensiónContenido DE Carton Descripción FuncionalPrologo Desempaquetado Y LimpiezaHerramientas DE Ensamblaje Requeridas EnsamblajeEstimación DEL Tiempo DE Ensamblaje RuedecillasMontaje DEL Tablero Firme Sujeción DEL Conjunto DE Motor Y Soplador AL ArmazónConjunto Operación Interruptor DE Encendido Y ApagadoFijación DEL Interruptor EN LA Posición DE Apagado Servicio Localizacion DE Fallas MantenimientoGarantia AccesoriosPlane , Whisper SERIES,WOODWORKER’S Choice