Craftsman 152.213371 operating instructions Blower and Motor Assembly to Base Assembly

Page 11

DO NOT assemble the Dust Collector until you are sure the tool IS NOT plugged in,

2, DO NOT assemble the Dust Collector until you are sure the power switch is in the "OFF" position,

2, For your own safety, DO NOT connect the machine to the power source until the machine is completely

assembled and you read and understand the entire Owner's Manual,

CASTER TO BASE ASSEMBLY

Fig. 7

B

A

insert threaded rod of caster (A) into the hob located on the underside of base (B) and fasten with 3/8" lock=washer (C) and 3/8-16 hex nut (D), See figure 7,

2, Assemble the remaining three casters to the under- side of the base in the same manner,

BLOWER AND MOTOR ASSEMBLY TO BASE ASSEMBLY

MAKE CERTAIN THE DUST COLLECTOR iS

DISCONNECTED FROM THE POWER SOURCE.

A

B

B

D E

1, Turn base (A) right side up, Align the mounting hobs at the base of blower and motor assembly (B) with six pre-drilled hobs (C) in base and fasten with six 5/16=18 x 5/8" hex head screws (D) and 5/16" lock washer (E), See figure 8,

Fig. 9

G

2, Assemble drum support (F) to the two threaded hobs in the corner of base with two 5/16=18 x 5/8"

hex head screws and 5/16" lock washer (G), NOTE: Do not completely tighten hardware at this time, See figure 9,

3, Assemble the remaining drum supports to the base in the same manner, NOTE: Do not completely tighten hardware at this time,

11

Image 11

Contents Sears, Roebuck and Co., Hoffman Estates, JL 60179 U.S.A ST CollRPM ONE-YEAR Full Warranty on Craftsman Professional Tool12, Keep Protective Guards in Place and in Working Order Before Usung the Dust Collector18AWG 21,EACHANDEVERYTmME,CHECK for DAMGujdeunes for Extension Cords Volt Operation only 25LONG 50LONGGrounded Outlet BOX Groundng Means VoltHoles For Dust Collectors SPECiFiC Safety iNSTRUCTiONSStock Number Available AccessoriesUnpacking AN Checking Contents and FigureHardware not Shown Page Disconnected from the Power Source Blower and Motor Assembly to Base AssemblyInlet U and tighten 6-inch hose clamp Make Certain the Dust Collector is Blower Motor AssemblyNlter and Collection BAG To Drum Assembly INTAKE Port toFlexible Hose to iNTAKE Port Assembly OFF POSiTiON Connecting Tool to Power SourceSTART/STOP Switch Locking Switch JNVolt Connection Dbconnected from the Power SourceDbconnect the Dust Collector from the Power Source Changing Motor VoltageTheuseof a lowratedmicronfilterandcollection ThingstoconsiderWhatisthemaximumC,RM,requiredforeachtool HelpfulhintsStatic Pressure Fiequjfements for a Dust Collection System MrequirementsfortoolsVariousFittings Problem TurnthepowerswitchOFFandunplugthepowerLikely Causes Solution AlwaysorderbyPARTNUMBER,notbykeynumber DUSTCOLLECTORPARTSUSTMODELNO.152.213371ON/OFF Page Page Para SU Seguridad Personal Anuai PropietarioRPM Seccion PaginaInstrucciones Generales DE Antes DE Utilizar EL Colector DE PolvoDE Largo Drectrices Para LAS Extensiones ElectricasDE LAS Drogas O DEL Alcohol Funcionamiento a 120 Voltios SolamenteConectado a Tierra Machos Portadores Machos PortadoresTomacorrbentesagujeros Orejeta DE AdaptadorPage Numero DE Exstencja Accesofhos DjsponjblesDesempaque Y DEL Contenjdo Figura 4 y Figura Ferreteria no Ilustrada Page Montaje DEL Ensamblado BEL Soplador Y EL Motor a LA Base Ensamblaje DE Ruedas Pjvotantes a LA BasePage Montaje DE LAS Bolsas DE Fjltro Y DE Recoleccjon AL Tambor Montaje DEL Puerto DE Admjsjon AL Motor DEL SopladorMontaje DE LA Ivianguera Flexible AL Puerto DE Djsyuntor DE Cjrcujtos Njando EL Jnterruptor a LA Posjcjon DE ApagadoConexion DE 240 Voltios Cambjando EL Voltaje DEL MotorConexion DE 120 Voltios Consejos Utiles Cosas a Tomarse EN CuentaCuadro de Requisitos De Presi6n Estatica Reductores Califieado comuniquese con el servicio de Sears Problema Causa Probable SolucionMstado DE Piezas DEL Colector DE Polvo O4/OFF Switch Circu Breaker Notas Ome