Craftsman 152.213371 operating instructions Flexible Hose to iNTAKE Port Assembly

Page 14

Fig. 16

4, Place

the second locking band

through

all the loops

 

of the

collection bag, similar to

the filter

bag,

5, Place the collection bag over the lower lip of the drum, Pull up on the retaining clips and insert cop lection bag underneath each retaining clip, Make

\

certain the locking band is positioned in the lower recessed channel of the drum and fasten clamp securely to drum,

D

2, Slide the lower support rod (C) onto the end of the upper support rod (B), Raise the assembled support rod with filter bag attached and place the end of the lower support rod into the hobs of the U=bracket (D), The flared end of lower support rod will prevent the rod from sliding through the U=bracket, See figure 16,

G F E

3, insert locking band (E) through all the loops of filter bag (F), Position the open end of the filter bag over the top lip of the drum, Make certain the locking band is positioned in the upper recessed channel of the drum and fasten clamp (G) securely to drum, See figure 17,

FLEXIBLE HOSE TO iNTAKE PORT ASSEMBLY

MAKE CERTAIN THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE.

IMPORTANT: When connecting an intake hose to one

or both intake ports, DO NOT REMOVE THE INTAKE PORT CAPS FROM THE INTAKE PORTS, Slide the

collar further back the intake port when attaching a hose,

1, To attach the 4-inch flexible hose to one of the intake ports, pull the intake port cap from the intake port, Slide the collar of the intake port cap further back the intake port and let the cap hang from the intake port,

2, Place 4=inch hose clamp over 4=inch flexible hose, Slide hose over one intake port opened Step 1 above and tighten hose clamp,

3, if you wish to use the second intake port, you should purchase a second 4=inch flexible hose and 4=inch hose clamp and repeat Steps 1 and 2 above,

See your nearest Sears Hardware Department or Sears Power and Hand Tool Catalog for other accessories,

Use only accessories recommended for this Dust Collector, Using other accessories may cause serious injury and cause damage to the Dust Collector,

14

Image 14
Contents ST Coll Sears, Roebuck and Co., Hoffman Estates, JL 60179 U.S.AONE-YEAR Full Warranty on Craftsman Professional Tool RPMBefore Usung the Dust Collector 12, Keep Protective Guards in Place and in Working OrderVolt Operation only 25LONG 50LONG 21,EACHANDEVERYTmME,CHECK for DAMGujdeunes for Extension Cords 18AWGGrounded Outlet BOX Groundng Means VoltHoles SPECiFiC Safety iNSTRUCTiONS For Dust CollectorsAvailable Accessories Stock NumberContents and Figure Unpacking AN CheckingHardware not Shown Page Blower and Motor Assembly to Base Assembly Disconnected from the Power SourceInlet U and tighten 6-inch hose clamp INTAKE Port to Blower Motor AssemblyNlter and Collection BAG To Drum Assembly Make Certain the Dust Collector isFlexible Hose to iNTAKE Port Assembly Locking Switch JN Connecting Tool to Power SourceSTART/STOP Switch OFF POSiTiONChanging Motor Voltage Dbconnected from the Power SourceDbconnect the Dust Collector from the Power Source Volt ConnectionHelpfulhints ThingstoconsiderWhatisthemaximumC,RM,requiredforeachtool Theuseof a lowratedmicronfilterandcollectionMrequirementsfortools Static Pressure Fiequjfements for a Dust Collection SystemVariousFittings Problem TurnthepowerswitchOFFandunplugthepowerLikely Causes Solution DUSTCOLLECTORPARTSUSTMODELNO.152.213371 AlwaysorderbyPARTNUMBER,notbykeynumberON/OFF Page Page Anuai Propietario Para SU Seguridad PersonalSeccion Pagina RPMAntes DE Utilizar EL Colector DE Polvo Instrucciones Generales DEFuncionamiento a 120 Voltios Solamente Drectrices Para LAS Extensiones ElectricasDE LAS Drogas O DEL Alcohol DE LargoOrejeta DE Adaptador Machos PortadoresTomacorrbentesagujeros Conectado a Tierra Machos PortadoresPage Accesofhos Djsponjbles Numero DE ExstencjaDesempaque Y DEL Contenjdo Figura 4 y Figura Ferreteria no Ilustrada Page Ensamblaje DE Ruedas Pjvotantes a LA Base Montaje DEL Ensamblado BEL Soplador Y EL Motor a LA BasePage Montaje DEL Puerto DE Admjsjon AL Motor DEL Soplador Montaje DE LAS Bolsas DE Fjltro Y DE Recoleccjon AL TamborMontaje DE LA Ivianguera Flexible AL Puerto DE Njando EL Jnterruptor a LA Posjcjon DE Apagado Djsyuntor DE CjrcujtosConexion DE 240 Voltios Cambjando EL Voltaje DEL MotorConexion DE 120 Voltios Cosas a Tomarse EN Cuenta Consejos UtilesCuadro de Requisitos De Presi6n Estatica Reductores Problema Causa Probable Solucion Califieado comuniquese con el servicio de SearsMstado DE Piezas DEL Colector DE Polvo O4/OFF Switch Circu Breaker Notas Ome