Craftsman 152.213371 INTAKE Port to, Blower Motor Assembly, Make Certain the Dust Collector is

Page 13

Fig. 13

1,

Align the four hobs in intake port (A) with the

 

 

 

 

mounting hobs in flange (B) of blower and motor

 

 

assembly and fasten with four M4,2 sheet metal

/

/

screws (C), See figure 14,

 

V

8, Attach the lower dust bag retaining clip (V) to the dust collector drum, Align both hobs (W) in the retaining clip with the two hobs in the drum, insert a 1/4-20 x 5/8" hex head screw through each hob

in the retaining clip and drum, Place a 1/4" fiat washer and 1/4-20 hex nut onto screw inside of the

drum, Repeat this process for the other three retaining clips and tighten all hardware,

See figure 13,

iNTAKE PORT TO

BLOWER MOTOR ASSEMBLY

MAKE CERTAIN THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE.

Fig. 15

0

0

E

D

2, Attach one intake port cap (D) to the intake port (E), The intake port caps must be placed into the intake ports when the intakes are not in use,

See figure 15,

IMPORTANT: When connecting an intake hose to one or both intake ports, DO NOT REMOVE THE INTAKE PORT CAP COLLARS (F} FROM THE INTAKE PORTS, Slide the collar further back when attaching a hose, See figure 15,

Fig. 14

B

NLTER AND COLLECTION BAG

TO DRUM ASSEMBLY

 

MAKE CERTAIN THE DUST COLLECTOR IS

 

DISCONNECTED FROM THE POWER SOURCE.

A

1, Hook the loop (A) on the top filter bag onto hook

(B) of the upper support rod, See figure 17,

 

13

Image 13
Contents Sears, Roebuck and Co., Hoffman Estates, JL 60179 U.S.A ST CollRPM ONE-YEAR Full Warranty on Craftsman Professional Tool12, Keep Protective Guards in Place and in Working Order Before Usung the Dust CollectorGujdeunes for Extension Cords 21,EACHANDEVERYTmME,CHECK for DAMVolt Operation only 25LONG 50LONG 18AWGHoles VoltGrounded Outlet BOX Groundng Means For Dust Collectors SPECiFiC Safety iNSTRUCTiONSStock Number Available AccessoriesUnpacking AN Checking Contents and FigureHardware not Shown Page Disconnected from the Power Source Blower and Motor Assembly to Base AssemblyInlet U and tighten 6-inch hose clamp Nlter and Collection BAG To Drum Assembly Blower Motor AssemblyINTAKE Port to Make Certain the Dust Collector isFlexible Hose to iNTAKE Port Assembly START/STOP Switch Connecting Tool to Power SourceLocking Switch JN OFF POSiTiONDbconnect the Dust Collector from the Power Source Dbconnected from the Power SourceChanging Motor Voltage Volt ConnectionWhatisthemaximumC,RM,requiredforeachtool ThingstoconsiderHelpfulhints Theuseof a lowratedmicronfilterandcollectionStatic Pressure Fiequjfements for a Dust Collection System MrequirementsfortoolsVariousFittings Likely Causes Solution TurnthepowerswitchOFFandunplugthepowerProblem AlwaysorderbyPARTNUMBER,notbykeynumber DUSTCOLLECTORPARTSUSTMODELNO.152.213371ON/OFF Page Page Para SU Seguridad Personal Anuai PropietarioRPM Seccion PaginaInstrucciones Generales DE Antes DE Utilizar EL Colector DE PolvoDE LAS Drogas O DEL Alcohol Drectrices Para LAS Extensiones ElectricasFuncionamiento a 120 Voltios Solamente DE LargoTomacorrbentesagujeros Machos PortadoresOrejeta DE Adaptador Conectado a Tierra Machos PortadoresPage Numero DE Exstencja Accesofhos DjsponjblesDesempaque Y DEL Contenjdo Figura 4 y Figura Ferreteria no Ilustrada Page Montaje DEL Ensamblado BEL Soplador Y EL Motor a LA Base Ensamblaje DE Ruedas Pjvotantes a LA BasePage Montaje DE LAS Bolsas DE Fjltro Y DE Recoleccjon AL Tambor Montaje DEL Puerto DE Admjsjon AL Motor DEL SopladorMontaje DE LA Ivianguera Flexible AL Puerto DE Djsyuntor DE Cjrcujtos Njando EL Jnterruptor a LA Posjcjon DE ApagadoConexion DE 120 Voltios Cambjando EL Voltaje DEL MotorConexion DE 240 Voltios Consejos Utiles Cosas a Tomarse EN CuentaCuadro de Requisitos De Presi6n Estatica Reductores Califieado comuniquese con el servicio de Sears Problema Causa Probable SolucionMstado DE Piezas DEL Colector DE Polvo O4/OFF Switch Circu Breaker Notas Ome