Bostitch 103618REVE Safety Instructions, AIR Supply and Connections, Loading Tool, Operation

Page 3

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1-1989 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide ade- quate protection.

CAUTION: ADDITIONAL SAFETY PROTECTION will be required in some environ- ments. For example, the working area may include exposure to noise level which can lead to hearing damage. The employer and user must ensure that any necessary hearing protection is provided and used by the operator and others in the work area. Some environments will require the use of head protection equipment. When required, the employer and user must ensure that head protection conforming to

ANSI Z89.1 1986 is used.

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

Do not use supply sources which can potentially exceed 200 P.S.I.G. as tool may burst, possibly causing injury.

The connector on the tool must not hold pressure when air supply is disconnect- ed. If a wrong fitting is used, the tool can remain charged with air after discon- necting and thus will be able to drive a fastener even after the air line is discon- nected possibly causing injury.

Do not pull trigger or depress contact arm while connected to the air supply as the tool may cycle, possibly causing injury.

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a dif- ferent work area, as accidental actuation may occur, possibly causing injury.

LOADING TOOL

When loading tool: 1.) Never place a hand or any part of body in fastener dis- charge area of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or depress the trip as accidental actuation may occur, possibly causing injury.

OPERATION

Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull the trigger unless nose is directed toward the work; 3.) Keep others a safe dis- tance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.

The operator must not hold the trigger pulled on contact arm tools except dur- ing fastening operation as serious injury could result if the trip accidentally con- tacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact arm tool may bounce from the recoil of driving a fastener and an unwanted second fasten- er may be driven possibly causing injury.

Check operation of the contact arm mechanism frequently. Do not use the tool if the arm is not working correctly as accidental driving of a fastener may result. Do not interfere with the proper operation of the contact arm mechanism.

Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury.

Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be deflected possibly causing injury.

MAINTAINING THE TOOL

When working on air tools note the warnings in this manual and use extra care when evaluating problem tools.

-3-

Page 2 Page 4
Image 3
Page 2 Page 4
Contents PC5000 Limited Warranty IntroductionIndex Operation Safety InstructionsAIR Supply and Connections Loading ToolOperation PC5000 Tool SpecificationsLubrication AIR Supply and ConnectionsTo Prevent Accidental Injuries Loading the PC5000Sequential Trip Operation Tool OperationTrigger Operation Contact Trip OperationTool Must Cycle Tool Operation CheckTrigger Operated Tool Tool Must not CycleBasic Tool Operation Replacement PartsAssembly Procedure for Seals AIR SUPPLY-PRESSURE and VolumeCoil Nailers Trouble ShootingAccessories Available Garantia Limitada IntroducciónÍndice NotaOperación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaEspecificaciones DE LA Herramienta PC5000 OperaciónPage Cómo Cargar EL PC5000 Operación DE LA Herramienta Operación DE Disparo POR ContactoOperación DE Disparo Secuencial LA Herramienta no Debe Efectuar SU Ciclo Verificación DE LA Operación DE LA HerramientaHerramienta Operada POR Gatillo Operación POR Disparo SecuencialPartes DE Reemplazo Presión Y Volumen DEL Suministro DE AireOperación Básica DE LA Herramienta Mantenimiento DE LA Herramienta NeumáticaClavadoras DE Bobina Diagnóstico DE FallaPage Sommaire RemarqueGarantie Limitée Fonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILOpération Caractéristiques DU PC5000Lubrification Pour Prévenir UN Accident Chargement DU PC5000Déclenchement À LA Volée Mode D’EMPLOIFonctionnement DE L’APPAREIL Avant DE Manipuler OU D’UTILISER CET OutilSystème DE Sécurité AU COUP-PAR-COUP Vérification DU Système DE DéclenchementDéclenchement PAR LA Détente Système DE Sécurité À LA Volée C.TPièces DE Rechange Diagramme DE Fonctionnement DE Base D’UN CloueurAlimentation D’AIR Pression Volume Entretien DE L’APPAREILProblèmes DE Fonctionnement Appareil À RouleauProblème Cause Correction Page Litho in U.S.A

103618REVE, PC5000 specifications

The Bostitch PC5000,103618REVE is a powerful and versatile pneumatic framing nailer designed for professionals and DIY enthusiasts alike. This tool is engineered to support a variety of construction applications, making it ideal for framing, roofing, and siding projects. With its robust construction and advanced features, the PC5000 delivers exceptional performance and efficiency.

One of the standout characteristics of the Bostitch PC5000 is its lightweight design, weighing in at just under 6 pounds. This makes it easy to maneuver, reducing user fatigue during extended use. The ergonomic grip further enhances comfort, allowing for improved control and precision when driving nails.

The PC5000 is equipped with a powerful motor that can drive nails ranging from 2 inches to 3-1/4 inches, making it capable of handling a wide variety of fastening applications. This nailer operates at a pressure range of 70 to 120 PSI, allowing users the flexibility to adjust according to the specific needs of their projects.

Another notable feature is the tool-free depth adjustment. This allows users to easily customize the driving depth of nails without the need for additional tools, ensuring optimal results for varying materials and applications. The Bostitch PC5000 also boasts a high-capacity magazine that holds up to 100 nails, reducing the need for frequent reloading and maintaining workflow efficiency on the job site.

The built-in nail lock-out mechanism is another safety feature that prevents dry firing, protecting both the tool and the material being worked on. Additionally, the selective trigger system allows for either sequential or contact firing modes, providing versatility based on the nature of the task at hand.

Furthermore, the Bostitch PC5000,103618REVE incorporates advanced technologies like an integrated air filter and a rubber grip, contributing to its durability and ease of use. The durable construction is designed to withstand harsh job site conditions, making it a reliable tool for contractors and builders.

In summary, the Bostitch PC5000,103618REVE combines portability, power, and user-friendly features, making it an excellent choice for professionals and DIYers looking for a high-performance framing nailer. Its efficient design, thoughtful technologies, and robust functionality set it apart in the competitive landscaping of pneumatic tools. Whether tackling large framing jobs or smaller projects, this nailer is sure to enhance productivity and deliver results.
Top Page Image Contents