Bostitch 103618REVE manual Loading the PC5000, To Prevent Accidental Injuries

Page 6

LOADING THE PC5000

EYE PROTECTION which conforms to ANSI specifications and provides protec- tion against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or ser- vicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1-1989 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide ade- quate protection.

TO PREVENT ACCIDENTAL INJURIES:

•Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

•Never point the tool at anyone else.

•Never engage in horseplay.

•Never pull the trigger unless nose is directed at the work.

•Always handle the tool with care.

•Do not pull the trigger or depress the trip mechanism while loading the tool.

1.Disengage the latch and pull back on the staple guide unit.

2.Insert the staples into the magazine. CAUTION: Load with points upward.

3.Push the staple guide unit closed, until the latch engages.

NOTE:

Use only fasteners recommended by Bostitch for PC5000 series staplers,

 

or fasteners which meet Bostitch specifications.

-6-

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PC5000 Limited Warranty IntroductionIndex Loading Tool Safety InstructionsAIR Supply and Connections OperationPC5000 Tool Specifications OperationAIR Supply and Connections LubricationLoading the PC5000 To Prevent Accidental InjuriesContact Trip Operation Tool OperationTrigger Operation Sequential Trip OperationTool Must not Cycle Tool Operation CheckTrigger Operated Tool Tool Must CycleAIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Basic Tool OperationTrouble Shooting Coil NailersAccessories Available Nota IntroducciónÍndice Garantia LimitadaAL Cargar LA Herramienta Instrucciones DE SeguridadSuministro DE Aire Y Conexiones OperaciónOperación Especificaciones DE LA Herramienta PC5000Page Cómo Cargar EL PC5000 Operación DE LA Herramienta Operación DE Disparo POR ContactoOperación DE Disparo Secuencial Operación POR Disparo Secuencial Verificación DE LA Operación DE LA HerramientaHerramienta Operada POR Gatillo LA Herramienta no Debe Efectuar SU CicloMantenimiento DE LA Herramienta Neumática Presión Y Volumen DEL Suministro DE AireOperación Básica DE LA Herramienta Partes DE ReemplazoDiagnóstico DE Falla Clavadoras DE BobinaPage Sommaire RemarqueGarantie Limitée Chargement DE L’APPAREIL Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement FonctionnementCaractéristiques DU PC5000 OpérationLubrification Chargement DU PC5000 Pour Prévenir UN AccidentAvant DE Manipuler OU D’UTILISER CET Outil Mode D’EMPLOIFonctionnement DE L’APPAREIL Déclenchement À LA VoléeSystème DE Sécurité À LA Volée C.T Vérification DU Système DE DéclenchementDéclenchement PAR LA Détente Système DE Sécurité AU COUP-PAR-COUPEntretien DE L’APPAREIL Diagramme DE Fonctionnement DE Base D’UN CloueurAlimentation D’AIR Pression Volume Pièces DE RechangeProblèmes DE Fonctionnement Appareil À RouleauProblème Cause Correction Page Litho in U.S.A

103618REVE, PC5000 specifications

The Bostitch PC5000,103618REVE is a powerful and versatile pneumatic framing nailer designed for professionals and DIY enthusiasts alike. This tool is engineered to support a variety of construction applications, making it ideal for framing, roofing, and siding projects. With its robust construction and advanced features, the PC5000 delivers exceptional performance and efficiency.

One of the standout characteristics of the Bostitch PC5000 is its lightweight design, weighing in at just under 6 pounds. This makes it easy to maneuver, reducing user fatigue during extended use. The ergonomic grip further enhances comfort, allowing for improved control and precision when driving nails.

The PC5000 is equipped with a powerful motor that can drive nails ranging from 2 inches to 3-1/4 inches, making it capable of handling a wide variety of fastening applications. This nailer operates at a pressure range of 70 to 120 PSI, allowing users the flexibility to adjust according to the specific needs of their projects.

Another notable feature is the tool-free depth adjustment. This allows users to easily customize the driving depth of nails without the need for additional tools, ensuring optimal results for varying materials and applications. The Bostitch PC5000 also boasts a high-capacity magazine that holds up to 100 nails, reducing the need for frequent reloading and maintaining workflow efficiency on the job site.

The built-in nail lock-out mechanism is another safety feature that prevents dry firing, protecting both the tool and the material being worked on. Additionally, the selective trigger system allows for either sequential or contact firing modes, providing versatility based on the nature of the task at hand.

Furthermore, the Bostitch PC5000,103618REVE incorporates advanced technologies like an integrated air filter and a rubber grip, contributing to its durability and ease of use. The durable construction is designed to withstand harsh job site conditions, making it a reliable tool for contractors and builders.

In summary, the Bostitch PC5000,103618REVE combines portability, power, and user-friendly features, making it an excellent choice for professionals and DIYers looking for a high-performance framing nailer. Its efficient design, thoughtful technologies, and robust functionality set it apart in the competitive landscaping of pneumatic tools. Whether tackling large framing jobs or smaller projects, this nailer is sure to enhance productivity and deliver results.
Top Page Image Contents