Bostitch 103618REVE, PC5000 manual Tool Operation, Trigger Operation, Contact Trip Operation

Page 7

TOOL OPERATION

EYE PROTECTION which conforms to ANSI specifications and provides pro- tection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1-1989 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

BEFORE HANDLING OR OPERATING THIS TOOL:

I.READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL.

II.REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL.

There are three available systems on BOSTITCH pneumatic tools. They are:

1. TRIGGER OPERATION 2. CONTACT TRIP OPERATION 3. SEQUENTIAL TRIP OPERATION

OPERATION

1. TRIGGER OPERATION

A TRIGGER OPERATED tool requires a single action to drive a fastener. Each time the trigger is pulled the tool will drive a fastener. The trigger operated model is intended for use only when a contact trip or sequential trip cannot be used due to the requirements of the application.

2. CONTACT TRIP OPERATION

The CONTACT TRIP MODEL tool contains a contact trip that operates in conjunction with the trigger to drive a fastener. There are two methods of operation to drive fasteners with a contact trip tool.

A. SINGLE FASTENER PLACEMENT: To operate the tool in this manner, first position the contact trip on the work surface, WITHOUT PULLING THE TRIGGER. Depress the contact trip until the nose touches the work surface and then pull the trigger to drive a fastener. Do not press the tool against the work with extra force. Instead, allow the tool to recoil off the work surface to avoid a second unwanted fastener. Remove your finger from the trigger after each operation.

B. RAPID FASTENER OPERATION: To operate the tool in this manner, hold the tool with the contact trip pointing towards but not touching the work surface. Pull the trigger and then tap the contact trip against the work surface using a bouncing motion. Each depression of the contact trip will cause a fastener to be driven.

The operator must not hold the trigger pulled on contact trip tools except during fastening operation, as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact trip tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven, possibly causing injury.

3. SEQUENTIAL TRIP OPERATION:

The SEQUENTIAL TRIP MODEL contains a contact trip that operates in conjunction with the trigger to drive a fastener. To operate a sequential trip tool, first position the contact trip on the work surface WITHOUT PULLING THE TRIGGER. Depress the con- tact trip and then pull the trigger to drive a fastener. As long as the contact trip is con- tacting the work and is held depressed, the tool will drive a fastener each time the trig- ger is depressed. If the contact trip is allowed to leave the work surface, the sequence described above must be repeated to drive another fastener.

-7-

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PC5000 Introduction Limited WarrantyIndex Operation Safety InstructionsAIR Supply and Connections Loading ToolOperation PC5000 Tool SpecificationsLubrication AIR Supply and ConnectionsTo Prevent Accidental Injuries Loading the PC5000Sequential Trip Operation Tool OperationTrigger Operation Contact Trip OperationTool Must Cycle Tool Operation CheckTrigger Operated Tool Tool Must not CycleBasic Tool Operation Replacement PartsAssembly Procedure for Seals AIR SUPPLY-PRESSURE and VolumeCoil Nailers Trouble ShootingAccessories Available Garantia Limitada IntroducciónÍndice NotaOperación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaEspecificaciones DE LA Herramienta PC5000 OperaciónPage Cómo Cargar EL PC5000 Operación DE Disparo POR Contacto Operación DE LA HerramientaOperación DE Disparo Secuencial LA Herramienta no Debe Efectuar SU Ciclo Verificación DE LA Operación DE LA HerramientaHerramienta Operada POR Gatillo Operación POR Disparo SecuencialPartes DE Reemplazo Presión Y Volumen DEL Suministro DE AireOperación Básica DE LA Herramienta Mantenimiento DE LA Herramienta NeumáticaClavadoras DE Bobina Diagnóstico DE FallaPage Remarque SommaireGarantie Limitée Fonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILOpération Caractéristiques DU PC5000Lubrification Pour Prévenir UN Accident Chargement DU PC5000Déclenchement À LA Volée Mode D’EMPLOIFonctionnement DE L’APPAREIL Avant DE Manipuler OU D’UTILISER CET OutilSystème DE Sécurité AU COUP-PAR-COUP Vérification DU Système DE DéclenchementDéclenchement PAR LA Détente Système DE Sécurité À LA Volée C.TPièces DE Rechange Diagramme DE Fonctionnement DE Base D’UN CloueurAlimentation D’AIR Pression Volume Entretien DE L’APPAREILAppareil À Rouleau Problèmes DE FonctionnementProblème Cause Correction Page Litho in U.S.A

103618REVE, PC5000 specifications

The Bostitch PC5000,103618REVE is a powerful and versatile pneumatic framing nailer designed for professionals and DIY enthusiasts alike. This tool is engineered to support a variety of construction applications, making it ideal for framing, roofing, and siding projects. With its robust construction and advanced features, the PC5000 delivers exceptional performance and efficiency.

One of the standout characteristics of the Bostitch PC5000 is its lightweight design, weighing in at just under 6 pounds. This makes it easy to maneuver, reducing user fatigue during extended use. The ergonomic grip further enhances comfort, allowing for improved control and precision when driving nails.

The PC5000 is equipped with a powerful motor that can drive nails ranging from 2 inches to 3-1/4 inches, making it capable of handling a wide variety of fastening applications. This nailer operates at a pressure range of 70 to 120 PSI, allowing users the flexibility to adjust according to the specific needs of their projects.

Another notable feature is the tool-free depth adjustment. This allows users to easily customize the driving depth of nails without the need for additional tools, ensuring optimal results for varying materials and applications. The Bostitch PC5000 also boasts a high-capacity magazine that holds up to 100 nails, reducing the need for frequent reloading and maintaining workflow efficiency on the job site.

The built-in nail lock-out mechanism is another safety feature that prevents dry firing, protecting both the tool and the material being worked on. Additionally, the selective trigger system allows for either sequential or contact firing modes, providing versatility based on the nature of the task at hand.

Furthermore, the Bostitch PC5000,103618REVE incorporates advanced technologies like an integrated air filter and a rubber grip, contributing to its durability and ease of use. The durable construction is designed to withstand harsh job site conditions, making it a reliable tool for contractors and builders.

In summary, the Bostitch PC5000,103618REVE combines portability, power, and user-friendly features, making it an excellent choice for professionals and DIYers looking for a high-performance framing nailer. Its efficient design, thoughtful technologies, and robust functionality set it apart in the competitive landscaping of pneumatic tools. Whether tackling large framing jobs or smaller projects, this nailer is sure to enhance productivity and deliver results.
Top Page Image Contents