Bostitch 103618REVE manual PC5000 Tool Specifications, Operation

Page 4

PC5000 TOOL SPECIFICATIONS

All screws and nuts are metric.

MODEL

LENGTH

HEIGHT

WIDTH

WEIGHT

PC5000

9.75” (248mm)

7.50” (190mm)

2.31” (59mm)

2.2lbs (1kg)

 

 

 

 

 

FASTENER SPECIFICATIONS:

TOOL MODEL

STAPLE SERIES

WIRE SIZE

MAXIMUM LEG LENGTH

PC5000

STCR5019

.050 x .019 (1.3 x .48mm)

9/16” (14mm)

TOOL AIR FITTING:

This tool uses a free-flow connector plug, 1/4” N.P.T. The minimum inside diameter should be .190" (4.8mm). The fitting must be capable of discharging tool air pressure when disconnected from the air supply.

OPERATING PRESSURE:

The operating pressure of the PC5000 tool is 60 to 100 p.s.i. (4.2 to 7.1 kg/cm2). Select the operating pressure within this range for best fastener performance.

DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.

AIR CONSUMPTION:

Model PC5000 requires 1.8 cubic feet per minute (.050 cubic meters) of free air to operate at the rate of 100 fasteners per minute, at 80 p.s.i. (5.6kg/cm2). Take the actual rate at which the tool will be run to determine the amount of air required. For instance, if your fastener usage averages 50 fasteners per minute, you need 50% of the tool's c.f.m. of free air which is required for running at 100 fasteners per minute.

OPERATION

BOSTITCH OFFERS THREE TYPES OF OPERATION FOR THIS SERIES TOOL.

CONTACT TRIP

The common operating procedure on “Contact Trip” tools is for the operator to contact the work to actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted. This will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly. All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip, and if unintentionally allowed to recontact the work surface with the trigger still actuated (finger still holding trigger pulled) an unwanted second fastener will be driven.

SEQUENTIAL TRIP

The Sequential Trip requires the operator to hold the tool against the work before pulling the trigger. This makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications.

The Sequential Trip allows exact fastener location without the possibility of driving a sec ond fastener on recoil, as described under “Contact Trip”.

The Sequential Trip Tool has a positive safety advantage because it will not accidentally drive a fastener if the tool is contacted against the work – or anything else – while the operator is holding the trigger pulled.

TRIGGER OPERATED

The Trigger Operated model is cycled by actuation of the trigger only. This model does not have a Contact Arm and is intended for use only where a Contact Arm CANNOT be used to satisfy the requirements of the application.

The Trigger Operated tool will cycle each time the trigger is actuated.

MODEL IDENTIFICATION:

Refer to Operation Instructions on page 4 before proceeding to use this tool.

CONTACT TRIP

SEQUENTIAL TRIP

TRIGGER OPERATED

Identified by:

Identified by:

Identified by:

BLACK TRIGGER

GRAY TRIGGER

BLACK TRIGGER

 

 

 

 

 

 

 

 

 

 

 

 

-4-

Page 3 Page 5
Image 4
Page 3 Page 5
Contents PC5000 Introduction Limited WarrantyIndex Safety Instructions AIR Supply and ConnectionsLoading Tool OperationPC5000 Tool Specifications OperationAIR Supply and Connections LubricationLoading the PC5000 To Prevent Accidental InjuriesTool Operation Trigger OperationContact Trip Operation Sequential Trip OperationTool Operation Check Trigger Operated ToolTool Must not Cycle Tool Must CycleReplacement Parts Assembly Procedure for SealsAIR SUPPLY-PRESSURE and Volume Basic Tool OperationTrouble Shooting Coil NailersAccessories Available Introducción ÍndiceNota Garantia LimitadaInstrucciones DE Seguridad Suministro DE Aire Y ConexionesAL Cargar LA Herramienta OperaciónOperación Especificaciones DE LA Herramienta PC5000Page Cómo Cargar EL PC5000 Operación DE Disparo POR Contacto Operación DE LA HerramientaOperación DE Disparo Secuencial Verificación DE LA Operación DE LA Herramienta Herramienta Operada POR GatilloOperación POR Disparo Secuencial LA Herramienta no Debe Efectuar SU CicloPresión Y Volumen DEL Suministro DE Aire Operación Básica DE LA HerramientaMantenimiento DE LA Herramienta Neumática Partes DE ReemplazoDiagnóstico DE Falla Clavadoras DE BobinaPage Remarque SommaireGarantie Limitée Consignes DE Sécurité Alimentation EN AIR Comprimé ET RaccordementChargement DE L’APPAREIL FonctionnementCaractéristiques DU PC5000 OpérationLubrification Chargement DU PC5000 Pour Prévenir UN AccidentMode D’EMPLOI Fonctionnement DE L’APPAREILAvant DE Manipuler OU D’UTILISER CET Outil Déclenchement À LA VoléeVérification DU Système DE Déclenchement Déclenchement PAR LA DétenteSystème DE Sécurité À LA Volée C.T Système DE Sécurité AU COUP-PAR-COUPDiagramme DE Fonctionnement DE Base D’UN Cloueur Alimentation D’AIR Pression VolumeEntretien DE L’APPAREIL Pièces DE RechangeAppareil À Rouleau Problèmes DE FonctionnementProblème Cause Correction Page Litho in U.S.A

103618REVE, PC5000 specifications

The Bostitch PC5000,103618REVE is a powerful and versatile pneumatic framing nailer designed for professionals and DIY enthusiasts alike. This tool is engineered to support a variety of construction applications, making it ideal for framing, roofing, and siding projects. With its robust construction and advanced features, the PC5000 delivers exceptional performance and efficiency.

One of the standout characteristics of the Bostitch PC5000 is its lightweight design, weighing in at just under 6 pounds. This makes it easy to maneuver, reducing user fatigue during extended use. The ergonomic grip further enhances comfort, allowing for improved control and precision when driving nails.

The PC5000 is equipped with a powerful motor that can drive nails ranging from 2 inches to 3-1/4 inches, making it capable of handling a wide variety of fastening applications. This nailer operates at a pressure range of 70 to 120 PSI, allowing users the flexibility to adjust according to the specific needs of their projects.

Another notable feature is the tool-free depth adjustment. This allows users to easily customize the driving depth of nails without the need for additional tools, ensuring optimal results for varying materials and applications. The Bostitch PC5000 also boasts a high-capacity magazine that holds up to 100 nails, reducing the need for frequent reloading and maintaining workflow efficiency on the job site.

The built-in nail lock-out mechanism is another safety feature that prevents dry firing, protecting both the tool and the material being worked on. Additionally, the selective trigger system allows for either sequential or contact firing modes, providing versatility based on the nature of the task at hand.

Furthermore, the Bostitch PC5000,103618REVE incorporates advanced technologies like an integrated air filter and a rubber grip, contributing to its durability and ease of use. The durable construction is designed to withstand harsh job site conditions, making it a reliable tool for contractors and builders.

In summary, the Bostitch PC5000,103618REVE combines portability, power, and user-friendly features, making it an excellent choice for professionals and DIYers looking for a high-performance framing nailer. Its efficient design, thoughtful technologies, and robust functionality set it apart in the competitive landscaping of pneumatic tools. Whether tackling large framing jobs or smaller projects, this nailer is sure to enhance productivity and deliver results.
Top Page Image Contents