Powermatic 31A Adjustments, Platen Adjustment, Sanding Table Adjustment, Refer to Figures 16

Page 15

Adjustments

Before putting power to the sander, inspect the machine thoroughly. Check to ensure that all screws are tight, all mechanical functions work freely, belt runs freely and tracks properly, and the disc runs freely, does not come into contact with the guard or table, and the abrasive remains firmly adhered to the sander’s metal disc.

Turn the motor on and check for proper rotation direction of the belts. The sanding belt should move from the idler pulley toward the drive pulley, while the disc should rotate counter- clockwise with the operator facing the disc. Arrow labels are affixed to the sander to indicate these directions.

Platen Adjustment

The platen should not require attention on your new sander. After prolonged use, however, the platen may occasionally need re-adjustment. To do this, proceed as follows.

Refer to Figure 15:

1.Swing the end guard out of position and remove the side cover. Remove the abrasive belt.

2.Using a 6mm hex wrench, loosen the two socket head cap screws inside the belt arm and shift the platen as needed. The platen should be 1/32” to 1/16” above the tangent points of the pulleys and in contact with the belt at both ends. A straight edge can be used with the abrasive belt to align the platen, as shown in Figure 15.

3.Re-tighten the socket head cap screws.

Sanding Table Adjustment

Refer to Figures 16 and 17:

The sanding table may be adjusted from any angle from 15 degrees up, to 45 degrees down. To adjust, loosen the locking wheels (A) on both sides and pivot the table to the desired angle as shown on the trunnion scale (B). Re-tighten the locking wheels (A).

A 45-degree stop (C) is located under the table. Use an angle measuring device to confirm that the angle of the table against the stop is 45 degrees. If it is not, adjust by loosening the hex nut and screwing the stop in or out as needed. Re-tighten hex nut.

Figure 15

Figure 16

Figure 17

15

Image 15
Contents Part No. M-0460267 PowermaticWarranty Period Warranty and ServiceTable of Contents Page Page Subject to local and national electrical codes Introduction SpecificationsAll grounded, cord-connected tools Grounding InstructionsDimensions On-Off Switch Padlock Unpacking Contents of the Shipping ContainerRefer to Figure AssemblyInstalling Sander on Stand Tools requiredInstalling Fence Installing and Tracking Abrasive BeltInstalling Table Installing Abrasive DiscSingle phase model Electrical ConnectionsDust Outlet and Cord Plate Extension Cords Converting from 230 Volt to 460 Volt Three Phase OnlyRefer to Figures 16 AdjustmentsPlaten Adjustment Sanding Table AdjustmentBelt Arm Positioning Work StopOperation Template FormsFence/Table Types of Operations Maintenance LubricationUse SAE No Oil on these Guide to Sanding Belts and Discs Probable Cause Remedy TroubleshootingReplacement Parts TroubleIndex No. Part No Description Size Qty Parts List 31A Stand Assembly 1PH31A Stand Assembly 1PH Parts List 31A Stand Assembly 3PH 31A Stand Assembly 3PH Parts List 31A Sander Body Assembly 31A-52 31A Sander Body Assembly Electrical Connections 1 Phase Electrical Page New Sanford Road LaVergne, Tennessee Parte Nro. M-0460267 Lijadora de Combinación Disco/CintaPeríodo de la Garantía Garantía y Servicio TécnicoPosicionamiento del Brazo de la Cinta ÍndicePage Guarde Estas Instrucciones Introducción Especificaciones Figura Instrucciones de Puesta a TierraCandado para Llave de Apagado Encendido DimensionesContenedor #2 Base DesempaqueRefiérase a la Figura MontajeInstalación de la Lijadora sobre la Base Herramientas RequeridasInstalación de la Guía Instalación y Ajuste de la Cinta AbrasivaInstalación de la Mesa Instalación del Disco AbrasivoConexiones Eléctricas Salida de Polvo y Cable de AlimentaciónInterruptor Cables de Extensión Instrucciones de Puesta a TierraRefiérase a la Figuras 16 y AjustesAjuste de la Platina Ajuste de la Mesa LijadoraPosicionamiento del Brazo de la Cinta Tope de TrabajoOperación Formas de PlantillasGuía/Mesa Tipos de Operaciones Mantenimiento LubricaciónUse Aceite SAE No sobre estos Guía para Cintas Lijadoras y Discos Causa Probable Solución Diagnóstico de ProblemasProblema Piezas de RepuestoNro. de Lista. Parte Nro Descripción Tamaño Cantidad Lista de Partes Conjunto de Base 31A 1ØConjunto de Base 31A 1Ø Lista de Partes Conjunto de Base 31A 3Ø Conjunto de Base 31A 3Ø Lista de Partes Conjunto del Cuerpo de Lijadora 31A 31A-53 Perno Bridado de Cabeza Hexagonal Conjunto del Cuerpo de Lijadora 31A Conexiones Eléctricas Monofásica Conexiones Page New Sanford Road LaVergne, Tennessee Pièce N. M-0460267 Courroie de combinaison/Ponceuse à disquePériode de garantie Garantie et entretienPositionnement du bras de courroie Table des matièresPage Retenez CES Instructions 1791292K Introduction SpécificationsOutils connectés de façon permanente Instructions de mise à la terreDimensions Cadenas du commutateur marche-arrêt Déballage Contenu du conteneur dexpédition Conteneur #1 ponceuseConteneur #2 support Referez-vous à la figure Installation de la ponceuse sur le supportAssemblage Outils requisInstallation du guide Installation et traçage de la courroie abrasiveInstallation de la table Installation du disque abrasifSortie des poussières et plaque de la rallonge Connexions électriquesConversion de 230 volts à 460 volts triphasé uniquement RallongesRéférez-vous aux figures 16 et RéglagesRéglage de la table Réglage de la table de ponçageArrêt de travail Positionnement du bras de courroieDesserrez le manche de verrouillage illustré sur la Figure Fonctionnement Formes de gabaritGuide/Table Types dopérations Graissage EntretienGuide de ponçage des courroies de des disques Anomalies Diagnostic des anomaliesCause possible Solution Pièces de rechange’indice N de la pièce Description Taille Qté Liste des pièces 31A Dispositif du support 1 Phase31A Dispositif du support 1 Phase Liste des pièces 31A Dispositif du support 3 Phase 31A Dispositif du support 3 Phase Liste des pièces 31A Dispositif du corps de la ponceuse Disque de ponçage acheté chez votre revendeur 31A Dispositif du corps de la ponceuse Branchements électriques 1 Phase Branchements Page New Sanford Road LaVergne, Tennessee Téléphone
Related manuals
Manual 28 pages 23.8 Kb

31A specifications

The Powermatic 31A is a high-performance 12" planer that has become a favorite among woodworkers and craft enthusiasts alike. Renowned for its powerful features and robust design, the 31A stands out in the woodworking community for its ability to deliver precision and efficiency in planing wood.

One of the key features of the Powermatic 31A is its 3 HP motor, which provides ample power for handling a wide range of hardwoods and softwoods. The motor is designed to run smoothly and quietly, reducing vibration during operation, which is essential for achieving fine finishes. The combination of power and stability allows users to tackle even the most challenging jobs with ease.

The machine is equipped with a 12" wide cutter head that utilizes four high-speed steel knives, which are known for their superior cutting capabilities. This allows for a smooth, even finish and reduces the amount of sanding required afterward. The adjustable infeed and outfeed tables are another notable feature, providing support for long workpieces and ensuring accuracy throughout the planing process.

In addition to its mechanical prowess, the Powermatic 31A boasts a quick elevation mechanism that allows users to make rapid adjustments to the height of the cutter head. This feature enhances efficiency and allows for easy transitions between different thicknesses of wood. The inclusion of a hinged cover also allows for quick access to the cutter head for maintenance and knife replacement, minimizing downtime.

The built-in dust collection system is another notable characteristic of the Powermatic 31A. This system helps to keep the workspace clean and safe by efficiently removing sawdust and debris, thereby ensuring that the work environment remains tidy and reducing the risk of respiratory issues caused by wood dust.

Moreover, the heavy-duty cast iron construction of the Powermatic 31A enhances its stability during operation, contributing to a better cutting experience. The robust design also ensures longevity, making it a reliable choice for both professional woodworkers and hobbyists.

With precision engineering and advanced technologies, the Powermatic 31A melds power and functionality, making it an indispensable tool for anyone serious about woodworking. Whether you are milling lumber for furniture-making or crafting intricate wood designs, this planer delivers in performance, making it a top-tier choice in its class.