Excell Precision E7540 Before Starting, Motor Overload Protector This motor has a manual

Page 14
Reset
Button
Drain Valve
Check Valve
Pressure
Release Valve

Drain Valve: The drain valve is located at the base of

the air tank and is used to drain condensation at the end of each use.

Check Valve: When the air compressor is operating, the check valve is "open", allowing compressed air to enter

the air tank. When the air compressor reaches "cut- out" pressure, the check valve "closes", allowing air

pressure to remain inside the air tank. Pressure Release Valve: The pressure release valve

located on the side of the pressure switch, is designed to automatically release compressed air from the compressor head and the outlet tube when the air compressor reaches "cut-out" pressure or is shut off. The pressure release valve allows the motor to restart freely. When the motor stops running, air will be heard escaping from this valve for a few seconds. No air should be heard leaking when the motor is running or after the unit reaches "cut-out" pressure.

Motor Overload Protector: This motor has a manual

thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down be- fore restarting. To restart:

1.Place the On/Auto/Off lever in the "Off" position.

2.Allow the motor to cool.

3.Depress the red reset button on the motor.

4. Place the On/Auto/Off lever in the "On/Auto" postion to restart the motor.

Air Intake Filter (not shown): This filter is designed to clean air coming into the pump. This filter must always be

clean and ventilation openings free from obstructions. See "Maintenance".

How to Use Your Unit

How to Stop:

1.Set the On/Auto/Off lever to "Off".

Before Starting

Break-in Procedure

Risk of Unsafe Operation. Serious damage may result if the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced.

1.Make sure the On/Auto/Off lever is in the "Off" position.

2.Check oil level in pump. See "Oil" paragraph in the Maintenance section for instructions.

3.Recheck all wiring. Make sure wires are secure at all terminals connections. Make sure all contacts move freely and are not obstructed.

4.Open the globe valve fully to permit air to escape and prevent air pressure build up in the air tank during the break-in period.

5.Move the On/Auto/Off lever to "On/Auto" position. The compressor will start.

A18791

14-ENG

Page 13 Page 15
Image 14
Page 13 Page 15
Contents E7540 Death or serious injury Or moderate injury Safety Guidelines DefinitionsImportant Safety Instructions Death or serious injuryHazard Spray area. An additional length of hoseFactory set operating pressures Accessories, tires, and other inflatablesExplosion For essential control of air pressure, youConsumption Powered device, If it is not usedElectricity. Like any other electrically Sprayed materials such as paint, paintHot for several minutes after operation Or attempt maintenance until unit hasResult in serious burns Do not reach around protective shroudsFire, Inhalation, Damage to Vehicle Surfaces Glossary SpecificationsAccessories Duty CycleTools Required for Assembly AssemblyContents of Carton UnpackingAnchoring of the Air Compressor InstallationLocation of the Air Compressor Wiring Instructions Voltage and Circuit ProtectionAir Distribution System AIR FlowKnow Your Air Compressor Pressure On/Auto/OffSwitch Tank Gauge Safety ValveOperation Description of OperationMotor Overload Protector This motor has a manual How to StopBefore Starting How to Start Before Each Start-UpMaintenance Customer ResponsibilitiesRemove the oil fill plug a CheckingChanging Air Filter Inspection and Replacement Motor Pulley/Flywheel Alignment Service and Adjustments Screwdriver Open position nothing is visibleStorage Troubleshooting Pressure reading A18791 24-ENG 25-ENG A18791 Limited Warranty Ou la mort Causer des blessures mineures ou Moyennes Mesures DE Sécurité DéfinitionsConsignes DE Sécurité Importantes Évité, peut causer des dommages à laConserver ces directives Avertissement Risque dexplosion ou dincendie PréventionAvertissement Risque de projection dobjets Avertissement Risque déclatementRisque Prévention Avertissement Risque de choc électrique Avertissement Risque par inhalationAvertissement Risque de chute Avertissement Risque de brûluresAvertissement Risque relié aux pièces mobiles Risque Avertissement Risque dune utilisation dangereuseLexique Cycle DE ServiceAccessoires Modèle no E7540Outils requis pour lassemblage AssemblageContenu de lemballage en carton DéballageEmplacement du compresseur dair Ancrage du compresseur dairÊtre effectué par un électricien qualifié Directives de câblageProtection contre la surtension et protection du circuit Du compresseur, les têtes et les cylindresSystème de distribution dair LES Conduites Principales DE Distribution DairUtilisation Familiarisez-vous avec votre compresseur dairArrêt de lappareil Utilisation de lappareilAvant le démarrage Procédures de rodageAvant chaque mise en marche Mise en marcheVérification de la soupape de sûreté EntretienResponsabilités du consommateur Une rupture ou une explosion du réservoir à airVérification Vidange du réservoirHuile ChangementRéglage de tension de la courroie Filtre à air Inspection et remplacementCourroie Remplacement Alignement de la poulie et du volant-moteur Boulons de la tête du compresseur serrageTournevis En position ouverte, rien nest visible Service d’entretien additionnelEntretien ET Réglages Rangement Rompre ou dexploser DépannageFaçon. Celui-ci risquerait de Niveau de la soup Soupape de sûreté Le moteur ne tourne pas Bruit de cliquetis 51-FR A18791 Garantie Limitée Responsabilité DE Lacheteur Dorigine utilisateur initialSerias Definiciones DE Normas DE SeguridadLesiones serias Instrucciones Importantes DE Seguridad ¿Cómo prevenirlo?Advertencia Riesgo de Explosión ¿Qué puede occurrir? ¿Cómo prevenirlo?Advertencia Riesgo de Inhalación ¿Qué puede occurrir? Advertencia Riesgo de Quemaduras ¿Qué puede occurrir? Advertencia Riesgo de Caída ¿Qué puede occurrir?Conservar Estas Instrucciones Ciclo DE Servicio EspecificacionesGlosario AccesoriosHerramientas necesarias para el ensamble EnsambladoContenido de la Caja DesembalajeAnclaje del compresor de aire InstalaciónUbicación del compresor de aire Ser efectuadas por un electricista calificado Instrucciones para la conexión eléctricaProtección del voltaje y del circuito Sistema de distribución de aire Descripción de operaciones OperaciónConozca su compresor de aire Cómo detenerla Cómo utilizar su unidadAntes de ponerlo en marcha Procedimiento de asentamientoAntes de cada puesta en marcha Cómo poner en marchaTanque, creando el riesgo de su ruptura o explosión MantenimientoCómo verificar la válvula de seguridad Erificación Cómo drenar el tanqueAceite CambioRegulación de la Tensión de la Correa Filtro de aire Inspección y reemplazoPolea y volante Alineación Nota Una vez que la polea del motor ha sidoTornillos del cabezal del compresor de aire. Torque Servicio Adicional Servicio Y AjustesPara reemplazar o limpiar la válvula de retención Almacenaje Originando un riesgo de ruptura de sus paredesPodría romperse o explotar Guía DE Diagnóstico DE ProblemasSobre la soldadura o cosa Pérdida de aire De acción retardada A18791 76-SP 77-SP A18791 Garantía Limitada

E7540 specifications

The Excell Precision E7540 is a cutting-edge piece of CNC machinery designed for precision engineering applications. This versatile machine is primarily used in the manufacturing sector for tasks that require high levels of accuracy and efficiency. The E7540 stands out due to its robust construction and sophisticated technologies that cater to modern industrial demands.

One of the standout features of the E7540 is its high-speed spindle, which allows for rapid material removal and reduced cycle times. The spindle’s speed can reach impressive RPMs, making it suitable for a wide range of materials, including metals, plastics, and composites. This capability is crucial for industries that require quick turnaround times without compromising on quality.

Additionally, the Excell E7540 is equipped with an advanced CNC control system, providing users with intuitive programming and operation capabilities. This user-friendly interface simplifies the setup process and allows operators to easily create complex machining operations. The control system supports various programming languages, making it adaptable for operators with different skill levels.

Another key feature of the E7540 is its high rigidity and stability, thanks to its solid cast iron base and precision-ground components. This structural integrity minimizes vibrations during the machining process, ensuring that the finished products meet strict tolerances. The machine also includes linear guides and ball screws that enhance motion accuracy, further improving the overall machining performance.

The Excell E7540 incorporates cutting-edge technologies such as adaptive control systems that adjust machining parameters in real time. This feature helps in optimizing cutting conditions based on material properties and tool wear, leading to improved tool life and reduced operational costs.

Moreover, the E7540 offers a generous working envelope, allowing for the machining of larger components without the need for multiple setups. Its automatic tool changer can handle a wide variety of tools, enabling quick transitions between different machining tasks.

In conclusion, the Excell Precision E7540 combines advanced engineering with innovative technologies to provide an exceptional machining experience. Its high-speed spindle, sophisticated control system, structural rigidity, and adaptive features make it an ideal choice for manufacturers looking to enhance productivity while maintaining unparalleled quality standards. As industries continue to evolve, the E7540 stands ready to meet the challenges of modern manufacturing.
Top Page Image Contents