Excell Precision E7540 operation manual Checking, Changing, Remove the oil fill plug a

Page 17
air tank until
Open Drain
Valve
Closed Drain
Valve

Drain Tank

NOTE: Operation of the air compressor will cause condensation to build up in the air tank. Always drain tank on a washable surface or in a suitable container to prevent damaging or staining surfaces.

1. Set the On/Auto/Off lever to "Off".

2. Close the globe valve.

3. Remove the air tool or accessory.

4. Open the globe valve and allow the air to slowly bleed from the tank pressure is approximately 20 psi.

5. Close the globe valve.

6. Drain water from air tank by opening drain valve on bottom of tank.

Risk of Bursting. Water will condense in the air tank. If not drained, water will corrode

and weaken the air tank causing a risk of air tank rupture.

7.After the water has been drained, close the drain valve. The air compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled.

Oil

NOTE: Use an oil specifically formulated for use in an air compressor, such as Porter-Cable PAS1 air compressor oil. Oil may be found at the store where the air compressor was purchased.

NOTE: Crankcase oil capacity is approximately 48 fluid ounces (1.4 L).

Checking

1.The oil level should be to the middle of the sight glass (C).

2.If needed remove oil fill plug (A) and slowly add oil until it reaches the middle of the sight glass.

Changing

1. Remove the oil fill plug (A).

A

2.Remove the oil drain plug (B) and drain oil into a suitable container.

3.Replace the oil drain plug (B) and tighten securely.

4.Sowly add compressor oil until

the oil level is in the middle of the

 

sightglass (C). NOTE: When filling

 

the crankcase, the oil flows very

 

slowly into the pump. If the oil is

C

added too quickly, it will overflow

 

and appear to be full.

B

Risk of Unsafe Opera-

 

 

tion. Overfilling with oil

 

will cause premature compressor failure. Do not overfill.

5.Replace oil fill plug (A) and tighten securely.

17-ENG

A18791

Page 16 Page 18
Image 17
Page 16 Page 18
Contents E7540 Important Safety Instructions Safety Guidelines DefinitionsDeath or serious injury Or moderate injury Death or serious injurySpray area. An additional length of hose HazardExplosion Accessories, tires, and other inflatablesFactory set operating pressures For essential control of air pressure, youElectricity. Like any other electrically Powered device, If it is not usedConsumption Sprayed materials such as paint, paintResult in serious burns Or attempt maintenance until unit hasHot for several minutes after operation Do not reach around protective shroudsFire, Inhalation, Damage to Vehicle Surfaces Accessories SpecificationsGlossary Duty CycleContents of Carton AssemblyTools Required for Assembly UnpackingAnchoring of the Air Compressor InstallationLocation of the Air Compressor Voltage and Circuit Protection Wiring InstructionsAIR Flow Air Distribution SystemOperation Pressure On/Auto/OffSwitch Tank Gauge Safety ValveKnow Your Air Compressor Description of OperationMotor Overload Protector This motor has a manual How to StopBefore Starting Before Each Start-Up How to StartCustomer Responsibilities MaintenanceRemove the oil fill plug a CheckingChanging Air Filter Inspection and Replacement Motor Pulley/Flywheel Alignment Screwdriver Open position nothing is visible Service and AdjustmentsStorage Troubleshooting Pressure reading A18791 24-ENG 25-ENG A18791 Limited Warranty Consignes DE Sécurité Importantes Mesures DE Sécurité DéfinitionsOu la mort Causer des blessures mineures ou Moyennes Évité, peut causer des dommages à laAvertissement Risque dexplosion ou dincendie Prévention Conserver ces directivesAvertissement Risque de projection dobjets Avertissement Risque déclatementRisque Prévention Avertissement Risque par inhalation Avertissement Risque de choc électriqueAvertissement Risque de chute Avertissement Risque de brûluresAvertissement Risque relié aux pièces mobiles Avertissement Risque dune utilisation dangereuse RisqueAccessoires Cycle DE ServiceLexique Modèle no E7540Contenu de lemballage en carton AssemblageOutils requis pour lassemblage DéballageAncrage du compresseur dair Emplacement du compresseur dairProtection contre la surtension et protection du circuit Directives de câblageÊtre effectué par un électricien qualifié Du compresseur, les têtes et les cylindresLES Conduites Principales DE Distribution Dair Système de distribution dairFamiliarisez-vous avec votre compresseur dair UtilisationAvant le démarrage Utilisation de lappareilArrêt de lappareil Procédures de rodageMise en marche Avant chaque mise en marcheResponsabilités du consommateur EntretienVérification de la soupape de sûreté Une rupture ou une explosion du réservoir à airHuile Vidange du réservoirVérification ChangementRéglage de tension de la courroie Filtre à air Inspection et remplacementCourroie Remplacement Boulons de la tête du compresseur serrage Alignement de la poulie et du volant-moteurTournevis En position ouverte, rien nest visible Service d’entretien additionnelEntretien ET Réglages Rangement Rompre ou dexploser DépannageFaçon. Celui-ci risquerait de Niveau de la soup Soupape de sûreté Le moteur ne tourne pas Bruit de cliquetis 51-FR A18791 Responsabilité DE Lacheteur Dorigine utilisateur initial Garantie LimitéeSerias Definiciones DE Normas DE SeguridadLesiones serias ¿Cómo prevenirlo? Instrucciones Importantes DE Seguridad¿Qué puede occurrir? ¿Cómo prevenirlo? Advertencia Riesgo de ExplosiónAdvertencia Riesgo de Inhalación ¿Qué puede occurrir? Advertencia Riesgo de Caída ¿Qué puede occurrir? Advertencia Riesgo de Quemaduras ¿Qué puede occurrir?Conservar Estas Instrucciones Glosario EspecificacionesCiclo DE Servicio AccesoriosContenido de la Caja EnsambladoHerramientas necesarias para el ensamble DesembalajeAnclaje del compresor de aire InstalaciónUbicación del compresor de aire Ser efectuadas por un electricista calificado Instrucciones para la conexión eléctricaProtección del voltaje y del circuito Sistema de distribución de aire Descripción de operaciones OperaciónConozca su compresor de aire Antes de ponerlo en marcha Cómo utilizar su unidadCómo detenerla Procedimiento de asentamientoCómo poner en marcha Antes de cada puesta en marchaTanque, creando el riesgo de su ruptura o explosión MantenimientoCómo verificar la válvula de seguridad Aceite Cómo drenar el tanqueErificación CambioPolea y volante Alineación Filtro de aire Inspección y reemplazoRegulación de la Tensión de la Correa Nota Una vez que la polea del motor ha sidoTornillos del cabezal del compresor de aire. Torque Servicio Adicional Servicio Y AjustesPara reemplazar o limpiar la válvula de retención Originando un riesgo de ruptura de sus paredes AlmacenajePodría romperse o explotar Guía DE Diagnóstico DE ProblemasSobre la soldadura o cosa Pérdida de aire De acción retardada A18791 76-SP 77-SP A18791 Garantía Limitada

E7540 specifications

The Excell Precision E7540 is a cutting-edge piece of CNC machinery designed for precision engineering applications. This versatile machine is primarily used in the manufacturing sector for tasks that require high levels of accuracy and efficiency. The E7540 stands out due to its robust construction and sophisticated technologies that cater to modern industrial demands.

One of the standout features of the E7540 is its high-speed spindle, which allows for rapid material removal and reduced cycle times. The spindle’s speed can reach impressive RPMs, making it suitable for a wide range of materials, including metals, plastics, and composites. This capability is crucial for industries that require quick turnaround times without compromising on quality.

Additionally, the Excell E7540 is equipped with an advanced CNC control system, providing users with intuitive programming and operation capabilities. This user-friendly interface simplifies the setup process and allows operators to easily create complex machining operations. The control system supports various programming languages, making it adaptable for operators with different skill levels.

Another key feature of the E7540 is its high rigidity and stability, thanks to its solid cast iron base and precision-ground components. This structural integrity minimizes vibrations during the machining process, ensuring that the finished products meet strict tolerances. The machine also includes linear guides and ball screws that enhance motion accuracy, further improving the overall machining performance.

The Excell E7540 incorporates cutting-edge technologies such as adaptive control systems that adjust machining parameters in real time. This feature helps in optimizing cutting conditions based on material properties and tool wear, leading to improved tool life and reduced operational costs.

Moreover, the E7540 offers a generous working envelope, allowing for the machining of larger components without the need for multiple setups. Its automatic tool changer can handle a wide variety of tools, enabling quick transitions between different machining tasks.

In conclusion, the Excell Precision E7540 combines advanced engineering with innovative technologies to provide an exceptional machining experience. Its high-speed spindle, sophisticated control system, structural rigidity, and adaptive features make it an ideal choice for manufacturers looking to enhance productivity while maintaining unparalleled quality standards. As industries continue to evolve, the E7540 stands ready to meet the challenges of modern manufacturing.
Top Page Image Contents