Grizzly G9953ZXF instruction manual Rewire To G4815 Only

Page 13

Rewire To 440V

(G4815 Only)

To rewire the Model G4815 to 440V:

1.Disconnect the sander from the power source!

2.Replace the power indicator light in the pedestal switch to one suitable for 440V operation

3.Remove the RHN-18 overload relay and replace it with a RHN-10 (8.5-12.5A) type, set to 10A (Figure 7).

RHN-10

Overload Relay

Figure 7. Overload relay.

4.Remove the CN-18 magnetic contact over- load relay and replace it with a CN-16 type (Figure 8).

CN-16

Magnetic

Contactor

Overload

Relay

Figure 8. Overload relay.

5.Wire the motor as shown on the diagram on the inside of the motor wire cover. Note— The circled references on the diagrams rep- resent labels on the wires. Also, Figure 9 below has been provided for your reference and are current at the time that this manual is being written. However, always use the dia- gram on the wire cover that comes with your motor!

G4815

Motor Wiring

4

5

6

4

5

6

7

8

9

7

8

9

1

2

3

1

2

3

R S T

R S T

220V

440V

Figure 9. 440V motor wiring.

 

 

 

 

 

 

 

 

 

 

 

 

Ultimate Series Jointers

-11-

Image 13
Contents Ultimate Series Jointers Page Table of Contents Safety Instructions For Power Tools SafetyLength Never Joint end grain Additional Safety Instructions For JointersCutterhead IntroductionModel G9953/G9953ZX Circuit RequirementsNEMA-style L15-20 plug and outlet Model G9953ZXFNEMA-style L15-30 plug and outlet Model G4815Grounding Minimum Cord SizeExtension Cords Motor wiring Ultimate Series Jointers Rewire To 440V G9953ZXF OnlyRewire To G4815 Only Main Components Unpacking SET UPParts Inventory Models G9953ZX, G9953ZXF, & G4815 QtyBolt Measure Hardware Recognition ChartWeight Load Clean UpSite Considerations Working ClearanceFence Beginning AssemblyTo mount the pedestal switch Pedestal SwitchDust Collection To attach dust collection hose to the dust portModel G9953 Only Knife To Outfeed Table AlignmentModels G9953ZX, G9953ZXF and G4815 Carbide Cutter To Outfeed Table AlignmentInfeed Table To Outfeed Table Alignment To verify the factory settingTo verify the 90˚ fence stop Fence StopsTo verify the 45˚ fence stop Main Stop lever Start UpOperations Operation SafetyStock Inspection & Requirements Squaring Stock Minimum dimensions For edge jointingIllustration of surface planing results Surface PlaningIllustration of edge jointing results Edge JointingIllustration of bevel cutting results Bevel CuttingMaintenance Safety MaintenanceGeneral Before each use, perform the following checksCarbide Cutters KnivesLubrication HandwheelsDate Approximate Hours Of Use Maintenance Performed Maintenance LogAdjustment Safety Service AdjustmentsLoosening the gib bolts Gib Gib Bolt Jack Screw Knife To set the knives Unplug the machine from the power sourceInstalling or adjusting the carbide cutters Infeed Table Cam To adjust the infeed tableRemoving the carbide cutters Page To set the 90˚ stop Using a bevel square to align fence Ultimate Series JointersDepth-Of-Cut Scale Date Approximate Hours Of Use Service Performed Service LogReference Info Machine Data Sheet Model G9953ZX 16 Ultimate Series Jointer Model G9953ZXF 16 Ultimate Series Jointer Model G4815 20 Ultimate Series Jointer Ultimate Series Jointers Ultimate Series Jointers Ultimate Series Jointers Ultimate Series Jointers Jointer Jointer Jointer Jointer Spiral Cutterhead Ultimate Series Jointers Jointer Figure Switch Special HEX Bolt Jointer Spiral Cutterhead Ultimate Series Jointers Jointer Jointer Jointer Jointer Jointer Jointer Jointer Bracket PB22M Symptom Possible Cause Corrective Action Troubleshooting GuideSee pages Ultimate Series Jointers Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog