Grizzly G9953ZXF, G4815 To set the knives Unplug the machine from the power source

Page 34

Knives

(Model G9953 Only)

Setting the knives correctly is crucial to the prop- er operation of the jointer and is very important in keeping the knives sharp. If one knife is higher than the others, it will do the majority of the work, and thus, dull much faster than the others. Note— The cutterhead knives should protrude above the cutterhead 2mm (0.079"). The knife jig included with the jointer is designed to set the knives with- in this height.

To set the knives:

1.Unplug the machine from the power source!

2.Open the access door on the back of the machine, just below the fence adjustments.

3.Turn the cutterhead pulley until the surface of the cutterhead is at top dead center.

4.Adjust the outfeed table to a height of 2mm above the surface of the cutterhead.

5.Turn the cutterhead pulley to reveal one of the knives.

6.Loosen the cutterhead gib bolts, starting in the middle, and alternating back and forth until all of the gib bolts are loose, but not falling out (Figures 34 and 35). Note—The gib bolts turn clockwise to loosen and coun- terclockwise to tighten (when facing the head of the bolt).

Tighten

 

 

 

 

Loosen

Knife

Gib Bolt

Gib

 

Figure 34. Loosening the gib bolts.

Gib Gib Bolt

Jack Screw

Knife

Figure 35. Components of the cutterhead.

-32-

Ultimate Series Jointers

Image 34
Contents Ultimate Series Jointers Page Table of Contents Safety Safety Instructions For Power ToolsLength Additional Safety Instructions For Jointers Never Joint end grainIntroduction CutterheadCircuit Requirements Model G9953/G9953ZXModel G9953ZXF NEMA-style L15-20 plug and outletModel G4815 NEMA-style L15-30 plug and outletGrounding Minimum Cord SizeExtension Cords Rewire To 440V G9953ZXF Only Motor wiring Ultimate Series JointersRewire To G4815 Only Main Components Parts Inventory SET UPUnpacking Models G9953ZX, G9953ZXF, & G4815 QtyHardware Recognition Chart Bolt MeasureSite Considerations Clean UpWeight Load Working ClearanceBeginning Assembly FenceDust Collection Pedestal SwitchTo mount the pedestal switch To attach dust collection hose to the dust portKnife To Outfeed Table Alignment Model G9953 OnlyCarbide Cutter To Outfeed Table Alignment Models G9953ZX, G9953ZXF and G4815To verify the factory setting Infeed Table To Outfeed Table AlignmentTo verify the 90˚ fence stop Fence StopsTo verify the 45˚ fence stop Start Up Main Stop leverOperations Operation SafetyStock Inspection & Requirements Minimum dimensions For edge jointing Squaring StockSurface Planing Illustration of surface planing resultsEdge Jointing Illustration of edge jointing resultsBevel Cutting Illustration of bevel cutting resultsGeneral MaintenanceMaintenance Safety Before each use, perform the following checksLubrication KnivesCarbide Cutters HandwheelsMaintenance Log Date Approximate Hours Of Use Maintenance PerformedService Adjustments Adjustment SafetyTo set the knives Unplug the machine from the power source Loosening the gib bolts Gib Gib Bolt Jack Screw KnifeInstalling or adjusting the carbide cutters Infeed Table Cam To adjust the infeed tableRemoving the carbide cutters Page Using a bevel square to align fence Ultimate Series Jointers To set the 90˚ stopDepth-Of-Cut Scale Service Log Date Approximate Hours Of Use Service PerformedReference Info Machine Data Sheet Model G9953ZX 16 Ultimate Series Jointer Model G9953ZXF 16 Ultimate Series Jointer Model G4815 20 Ultimate Series Jointer Ultimate Series Jointers Ultimate Series Jointers Ultimate Series Jointers Ultimate Series Jointers Jointer Jointer Jointer Jointer Spiral Cutterhead Ultimate Series Jointers Jointer Figure Switch Special HEX Bolt Jointer Spiral Cutterhead Ultimate Series Jointers Jointer Jointer Jointer Jointer Jointer Jointer Jointer Bracket PB22M Troubleshooting Guide Symptom Possible Cause Corrective ActionSee pages Ultimate Series Jointers Warranty & Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog