Master Appliance UT-100 instruction manual UT-200 Ignition Instructions for use as a Butane Torch

Page 7

UT-200 Ignition Instructions for use as a Butane Torch

1112

1.Remove protective cap. (Do not twist off). Remove the soldering or heat tip by turning the knurled nut and tip housing to the right (figure 11) Retighten knurled nut (Do not over tighten) Never change tips while hot.

2.Lower shutter knob and ignite after turning gas lever to open position (figure 12).

3.The flame size can be controlled by the gas control lever.

Important Safety Instructions

To reduce the risk of injury or property damage, READ AND UNDERSTAND the following warnings:

1.To prevent fire or damage to work surfaces, be sure hot air exhaust opening is positioned up. Hot air comes out of the exhaust opening in the tip. Keep combustibles and hands away from the opening.

2.To prevent fuel tank leakage, do not store in environmental area that exceeds 104°F/40°C (such as car dashboard or trunk, direct sun, glove com- partment, or other enclosed, unventilated areas).

3.Be sure to turn “ON/OFF” switch to “OFF” after use.

4.Do not perform maintenance or re-pair unless unit is com- pletely cool. Be certain “ON/OFF” lever is “OFF”.

5.Wait for tips to cool before changing. Keep hands and combustibles from tip area while in use.

6.When soldering or desoldering always review material safety data sheets (MSDS) for rec- ommended precautions for safe handling and use of

solder, solder paste, flux, conformal coatings and any other chemicals.

7.Store away from, and do not use in the presence of chil- dren.

8.Keep protective cap on unit while not in use.

9.Use only in well-ventilated area. Continuous or extended use indoors should be done only with a local exhaust ven- tilation to the outside.

10.Do not expose to open flame or other sources of high tem- perature.

11.To prevent clouding of win- dow, do not use alcohol or alcohol-based cleaner.

12.Use only Master Appliance Ultratane Butane Fuel to insure maximum safety and performance. MSDS upon request.

13.Always use safety glasses or goggles.

14.Do not fill gas or store near open flame, heater, furnace or combustible materials.

15.Do not misuse, abuse, alter or tamper.

16.It is your responsibility to fol- low your governmental regu- lations when disposing of this unit.

NOTE: When operating in extremes of temperature (hot or cold), at high altitude, ignition may be difficult due to the varia- tion of gas pressure caused by these extremes. Gas control set- tings will also be affected and will vary from those under normal conditions. If difficulties are experienced, please contact our Customer Service Department who will advise on adjustment.

WARNING: The Department of Transportation Hazardous Material Regulations forbid the carriage of butane or other flam- mable gas products on passen- ger aircraft. Do not pack this item or any other flammable gas item, in any checked or carry-on bag- gage.

WARNING: This product, when used for soldering and similar applications, produces chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Made in Japan UT-100 UT-200 Ultratorch Heat ToolsAvis Réglementaires Regulatory InformationInformación de reglamentos Ignition Vent Hot Air Exhaust Opening Tip HousingDescription Hot Air Exhaust Knurled NutUse as a Soldering Iron, Heat Tool or Torch Principles of OperationFill with Ultratane Butane Page UT-100 Ignition Instructions for use as a Butane Torch Before using as soldering or heat toolDo not misuse, abuse, alter or tamper Important Safety InstructionsAlways use safety glasses or goggles UT-200 Ignition Instructions for use as a Butane TorchOverall length with soldering tip 242mm How to Empty Tank of Butane Gas if NeededSpecifications One gas filling At #3 settingSoldering Tips Optional Accessories UT-100Heat Tips Carrying Strap Optional Accessories UT-200Heat Shrink Attachment Protective CapTo Replace Ejector Trouble ShootingProblem Probable cause Solution Set flow control valve at settingOne Year Full Warranty Avertissements Évacuation Catalyseur d’air chaud Principes de fonctionnementRemplir avec du butane Ultratane Le gaz butane continue à passer sur le catalyseurPage Ou de chauffe par l’éjecteur pour chalumeau On off est sur « OFF » Consignes de sécurité importantesCaractéristiques Comment vider le réservoir de gaz butane, si nécessairePannes de soudage Accessoires UT-100 en optionPointes chauffantes Bouchon protecteur Accessoires UT-200 en optionButane Ultratane Pour remplacer l’éjecteur DépannageRangement de votre outil de chauffe Ultratorch Garantie d’un an Descripción AdvertenciasUso como cautín, herramienta de calor o soplete Principios de operaciónCargue con gas butano Ultratane Page El expulsor del soplete Siempre use lentes o gafas de seguridad Instrucciones importantes de seguridadDuración de una carga de gas Cómo vaciar el tanque de gas butano si es necesarioEspecificaciones Largo total con punta de cautín 242 mm 9.5Puntas de soldar Accesorios opcionales del UT-100Puntas de calor Gas butano Ultratane Accesorios opcionales del UT-200Reemplazo del expulsor Búsqueda y solución de problemasAlmacenamiento de su herramienta de calor Ultratorch Racine, Wisconsin 53403 U.S.A. Teléfono 800-558-9413 Fax Garantía por un año completo

UT-200, UT-100 specifications

The Master Appliance UT-100 and UT-200 are high-performance heat guns designed for professionals and hobbyists alike. These tools are recognized for their versatility, durability, and advanced features, making them ideal for various applications, from soldering and shrink tubing to removing paint and thawing frozen pipes.

One of the key features of both the UT-100 and UT-200 is their adjustable temperature control. Users can easily regulate the heat output to suit specific tasks, ensuring optimal temperature for materials without the risk of damage. The UT-100 offers a temperature range of 200°F to 1000°F, while the UT-200 enhances this capability with a broader range of 200°F to 1200°F, allowing for more intricate and high-heat applications.

In terms of design, the heat guns are lightweight and ergonomic, making them comfortable to use for extended periods. They come equipped with a safety guard to prevent accidental contact with the hot nozzle. The integrated stand allows the tools to be set down safely while in use, providing added convenience and reducing user fatigue.

Both models utilize advanced heating element technology to deliver rapid heat-up times, ensuring that you spend less time waiting and more time working. The durable construction of Master Appliance tools ensures longevity and reliability, even in demanding work environments.

The UT-200 takes it a step further with a variable airflow feature, allowing users to emit air at different speeds without the need for additional attachments. This flexibility increases the adaptability of the tool for various tasks, such as delicate work on electronic components or heavy-duty applications needing high air movement.

Moreover, these heat guns are equipped with replaceable nozzles and accessories, enhancing their functionality. Users can choose from a variety of nozzle configurations, depending on the task at hand, such as concentrated beams for soldering or wide nozzles for heat shrinking.

Both models also prioritize user safety, featuring built-in thermal protection that prevents overheating, safeguarding both the tool and the user. The Master Appliance UT-100 and UT-200 represent a significant investment for those looking for high-quality, versatile heat guns that meet the demands of any project. Their blend of performance, durability, and user-friendly design makes them essential tools for professionals in various industries.
Top Page Image Contents