Master Appliance UT-100 Trouble Shooting, To Replace Ejector, Problem Probable cause Solution

Page 11

Trouble Shooting

Problem

 

Probable cause

 

Solution

 

 

Does not ignite

 

a. Empty tank

 

a. Refill with butane fuel

 

b. Clogged ejector

 

b. Replace with new ejector

 

 

 

 

 

c. Fuel setting too high

 

c. Adjust switch ring or gas

 

 

 

 

control lever to lower setting

Low gas pressure

 

a. Foreign object blocking tips

 

a. Clean out or replace tips

Low flame

 

b. Cold fuel

 

b. Hold unit in hand to allow unit

 

 

 

 

to warmup. DO NOT HEAT HANDLE.

Not enough heat

 

a. Used-up catalyst

 

a. Replace with new tip

 

b. Low fuel

 

b. Refill with butane gas

 

 

 

Note: Ultratorches utilize the energy produced while evaporating butane gas. Ambient temperature affects operation. Adjust the unit as necessary.

To Replace Ejector

The ejector is where the air/fuel mixture takes place. Occasionally it may be neces- sary to replace due to clogging.

Unscrew the knurled nut and remove the tip and tip housing. Push shutter lever upward to expose the small holes on the

solder/heat ejector. Insert the accessory spanner wrench into one of the small holes and turn counter clockwise (CCW) until loose. (Continue to turn until easily removed.) Mount the new ejector in place of the removed ejector. Point the torch ejector downward and

turn clock wise (CW), by hand, until tight. Use span- ner wrench to tighten com- pletely. Replace tip and tip housing.

Storage of Your Ultratorch Heat Tool

1.Allow unit to cool and put protective cap on for storage.

2.If your unit is not going to be used for awhile, store in the following manner. Store in

proper location avoiding elevated temperatures and away from children.

3.Leave tank approximately 1/2 full so lubrication of fuel pickup filter stays wet.

4.Set flow control valve at setting 5.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Made in Japan UT-100 UT-200 Ultratorch Heat ToolsInformación de reglamentos Regulatory InformationAvis Réglementaires Ignition Vent Hot Air Exhaust Opening Tip HousingDescription Hot Air Exhaust Knurled NutFill with Ultratane Butane Principles of OperationUse as a Soldering Iron, Heat Tool or Torch Page UT-100 Ignition Instructions for use as a Butane Torch Before using as soldering or heat toolDo not misuse, abuse, alter or tamper Important Safety InstructionsAlways use safety glasses or goggles UT-200 Ignition Instructions for use as a Butane TorchOverall length with soldering tip 242mm How to Empty Tank of Butane Gas if NeededSpecifications One gas filling At #3 settingHeat Tips Optional Accessories UT-100Soldering Tips Carrying Strap Optional Accessories UT-200Heat Shrink Attachment Protective CapTo Replace Ejector Trouble ShootingProblem Probable cause Solution Set flow control valve at settingOne Year Full Warranty Avertissements Évacuation Catalyseur d’air chaud Principes de fonctionnementRemplir avec du butane Ultratane Le gaz butane continue à passer sur le catalyseurPage Ou de chauffe par l’éjecteur pour chalumeau On off est sur « OFF » Consignes de sécurité importantesCaractéristiques Comment vider le réservoir de gaz butane, si nécessairePointes chauffantes Accessoires UT-100 en optionPannes de soudage Butane Ultratane Accessoires UT-200 en optionBouchon protecteur Rangement de votre outil de chauffe Ultratorch DépannagePour remplacer l’éjecteur Garantie d’un an Descripción AdvertenciasCargue con gas butano Ultratane Principios de operaciónUso como cautín, herramienta de calor o soplete Page El expulsor del soplete Siempre use lentes o gafas de seguridad Instrucciones importantes de seguridadDuración de una carga de gas Cómo vaciar el tanque de gas butano si es necesarioEspecificaciones Largo total con punta de cautín 242 mm 9.5Puntas de calor Accesorios opcionales del UT-100Puntas de soldar Gas butano Ultratane Accesorios opcionales del UT-200Almacenamiento de su herramienta de calor Ultratorch Búsqueda y solución de problemasReemplazo del expulsor Racine, Wisconsin 53403 U.S.A. Teléfono 800-558-9413 Fax Garantía por un año completo

UT-200, UT-100 specifications

The Master Appliance UT-100 and UT-200 are high-performance heat guns designed for professionals and hobbyists alike. These tools are recognized for their versatility, durability, and advanced features, making them ideal for various applications, from soldering and shrink tubing to removing paint and thawing frozen pipes.

One of the key features of both the UT-100 and UT-200 is their adjustable temperature control. Users can easily regulate the heat output to suit specific tasks, ensuring optimal temperature for materials without the risk of damage. The UT-100 offers a temperature range of 200°F to 1000°F, while the UT-200 enhances this capability with a broader range of 200°F to 1200°F, allowing for more intricate and high-heat applications.

In terms of design, the heat guns are lightweight and ergonomic, making them comfortable to use for extended periods. They come equipped with a safety guard to prevent accidental contact with the hot nozzle. The integrated stand allows the tools to be set down safely while in use, providing added convenience and reducing user fatigue.

Both models utilize advanced heating element technology to deliver rapid heat-up times, ensuring that you spend less time waiting and more time working. The durable construction of Master Appliance tools ensures longevity and reliability, even in demanding work environments.

The UT-200 takes it a step further with a variable airflow feature, allowing users to emit air at different speeds without the need for additional attachments. This flexibility increases the adaptability of the tool for various tasks, such as delicate work on electronic components or heavy-duty applications needing high air movement.

Moreover, these heat guns are equipped with replaceable nozzles and accessories, enhancing their functionality. Users can choose from a variety of nozzle configurations, depending on the task at hand, such as concentrated beams for soldering or wide nozzles for heat shrinking.

Both models also prioritize user safety, featuring built-in thermal protection that prevents overheating, safeguarding both the tool and the user. The Master Appliance UT-100 and UT-200 represent a significant investment for those looking for high-quality, versatile heat guns that meet the demands of any project. Their blend of performance, durability, and user-friendly design makes them essential tools for professionals in various industries.
Top Page Image Contents