Multiquip 8FP Series manual Installing a Replacement V-BELT or Pulley, Application As Specified

Page 33

ASSEMBLY INSTRUCTIONS/OPERATIONS

4)Using the 1/2 inch wrenches, loosen the engine/electric motor attachment capscrews, and slide the engine/electric motor toward the front of the main frame. FIGURE 34.

FIGURE 33

INSTALLING A REPLACEMENT V-BELT OR

PULLEY

Application: As Specified.

Tools Required:

1each, 7/16 inch wrench.

2each, 1/2 inch wrenches.

1each, 9/16 inch wrench.

1each, 16 inch minimum length straightedge.

1each, 10 lbs minimum capacity, tension scale or belt tension tool.

1each, torque wrench, 35 ft lbs (47 Nm.) capacity with 7/16 inch and 9/16 inch sockets.

Parts Required:

1each, PN 29020-056 V-belt 3VX335 (if required).

1each, PN 29020-038 bushing (if required).

1each, PN 29020-037 pulley (if required).

1each, PN 10057-016 key (if required).

1) If the Floor Planer is powered by an engine, disconnect the spark plug wire. If powered by an electric motor, disconnect the extension cord or Floor Planer from the power source.

2)Position the Floor Planer on a suitable work surface with the V-belt approximately at waist level.

3)Using the 9/16 inch wrench, remove the belt guard from the main frame. Clean the inside of the belt guard with an appropriate solvent. Check for signs of wear and damage.

CAUTION

Observe all applicable safety precautions for the solvent.

3)Using a 1/2 inch wrench, remove the self locking nuts on the engine/electric motor take-up capscrews. Rotate the take-up capscrews until the hexagon head contacts the threaded mounting plate.

FIGURE 34

5)Remove the worn belt and install the replacement V-belt, PN 29020-056 (3VX335).

a) Do not install a replacement belt if the pulleys have worn grooves. Such pulleys should be replaced to insure proper belt fit. Operating the V-belt in worn pulley grooves will accelerate V-belt wear and significantly reduce its service life.

b)A V-belt should never be forced over a pulley. More belts are broken from this cause than from actual failure in service.

c)Keep the belt as clean and free of foreign material as possible. Do not use belt dressing.

6)Reinstall the engine/electric motor take-up capscrews with the heads facing toward and in contact with the engine crankcase/electric motor thrust plate. Tighten the engine/electric motor attachment capscrews until they just begin to apply tension to the engine/electric motor. DO NOT OVER TIGHTEN. Alternately tighten the take-up capscrews until slight tension is applied to the V-belt.

7)The driveshaft pulley should be positioned within 1/16 inch if the shaft shoulder. If the distance exceeds this limit, proceed as follows:

a) Using the 7/16 inch wrench, remove the two 1/4 inch diameter capscrews from the bushing.

b)Insert the capscrews into the tapped holes in the bushing flange. Tighten progressively until the bushing disengages from the pulley.

c)Insert the 1/4 inch diameter capscrews into the tapped holes in the pulley. Tighten progressively until the bushing applies tension to the pulley. FIGURE 35.

8FP FLOOR PLANER SERIES

OPERATION AND PARTS MANUAL REV #2 (05/28/09)

PAGE 33

 

 

 

Image 33
Contents Electric and Gasoline Floor Planers Model 8FP Series Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Removing the Floor Planer from the Pallet Application All ModelsFilling the 8FP/G Series Engine Fuel Tank Flail Design and Application Theory of OperationBeam Flail Star FlailMilling Flail Pentagonal FlailFunction of Spacer Washers Spacer WashersProblems encountered by uneven component wear Flail Drum Design and Application General Notes Regarding Flail Drums Installing Flails on the TWO Section DrumNormal installation procedure for milling flails Installing a Loaded Drum on the Driveshaft General Notes Regarding the Installation of FlailsTransporting the Floor Planer Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Floor Planer on the JOB Site Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Stopping the 8FP/E Series Electrically Powered Floor Planer Stopping the 8FP/G Series Gasoline Powered Floor PlanerPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent Application As Specified Installing a Replacement V-BELT or PulleyAssembly INSTRUCTIONS/OPERATIONS Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Aligning the Caster Wheels Checking Driveshaft RUN OUT Page MAINTENANCE/SERVICE Engine ServiceApplication 8FP/G Series Floor Planer Troubleshooting Accelerated V-BELT Wear Accelerated Bearing Wear AND/OR FailureUneven Cutting Action Storage StorageGeneral FrameExplanation of Code in Remarks Column Qty Description Suggested Spare PartsMain Frame Assy Main Frame AssemblyFRAME, Main Main Frame Assy Part Name QTYTUBE, Vacuum Axle MountDriveshaft Assy Driveshaft AssemblyRING, Retaining External Driveshaft Assy Part Name QTY. RemarksSHEAVE, Driveshaft KEY, SpecialRear Frame Assy Rear Frame AssemblyPIN, Roll 3/16 X 1 Plated Rear Frame Assy Part Name QTY RemarksBUSHING, Connex SHAFT, Hinge PlatedOperator Handle Assy Gasoline Operator Handle Assembly GasolineBARREL, Adjusting BOOT, RubberSWITCH, SHUT-OFF TAP, 22-18 Guage WireGasoline Engine Assy Gasoline Engine AssemblyFRAME, Main GX160KQXC9 ENGINE, Honda 5.5HP Part Name QTY. RemarksDrive Pulley BUSHING, Center HUBOperator Handle Assy Operator Handle Assembly ElectricAdjusting Tube Switch Mount Height Adjustment ScrewHOUSING, Switch SWITCH, ON/OFFElectric Motor Assy Electric Motor AssemblyMotor Plate MOTOR, Electric 5HPRELIEF, Strain NUT, BulklheadONE Section Drum Assy ONE Section Drum AssemblyFlail Drum END CAP ONE Section Drum Assy Part NameFlail Drum ROD WASHER, Lock 1/4TWO Section Drum Assy TWO Section Drum AssemblyFlail Drum 2 Section TWO Section Drum Assy Part NameFlails & Spacer Washers Assy FLAILS, Spacers and Washers AssemblyStar Flail FLAILS, Spacers and Washers Assy Part Name QTYSpacer Washer Beam FlailDecals Decal Warning Flails Decals Part Name QTY RemarksDecal Depth Control Decal MQ LogoEffective February 22 Page HERE’S HOW to GET Help