Multiquip 8FP Series manual Assembly INSTRUCTIONS/OPERATIONS

Page 37

ASSEMBLY INSTRUCTIONS/OPERATIONS

FIGURE 44

10)Mount the bearing block/driveshaft assembly to the main frame. Tighten the 3/8 inch self-locking hex nuts with the torque wrench to 35 ft lbs (47 Nm.)

11)Follow the instructions as outlined for

INSTALLING A REPLACEMENT-BELT OR PULLEY to complete the assembly of the pulleys, V-belt and belt guard.

Aproperly installed, replacement bearing should rotate without excessive friction, drag and/or "rough spots". If these symptoms occur after assembly, the bearing was improperly supported when pressed on the driveshaft or into the housing. The resulting thrust placed upon the bearing exceeded its static capacity. A bearing operating with these characteristics will deliver minimal service life and be prone to premature failure.

12)If the Floor Planer is powered by an engine, reconnect the engine spark plug wire. If powered by an electric motor and the machine is to be used immediately, reconnect the extension cord or Surface Grinder to the power source. Determine that the ON/OFF switch located on the operator handle is in the OFF position.

DANGER

UNEXPECTED MACHINE START UP CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

INSTALLING A REPLACEMENT BEARING ON THE

OUTBOARD SIDE.

Application: All Models.

Tools Required:

1each, 5/16 wrench.

1each, 3/4 wrench.

1each, 5/16 Allen wrench.

1 each, arbor press.

1each, torque wrench, 85 ft lbs (115 Nm.) capacity, with 5/15 inch, male Allen head and 9/16 socket.

1each, pliers for large, external type snap rings.

Parts Required:

1 each, 29020-016 bearing.

1 each, 29020-015 snap ring (if required).

1)If the Floor Planer is powered by an engine, disconnect the spark plug wire. If powered by an electric motor, disconnect the extension cord or Floor Planer from the power source.

2)Position the Floor Planer on a suitable work surface with the V-belt approximately at waist height.

3)Using a 3/4 inch wrench, remove the access plate capscrews. Remove the access plate.

4)Using the 5/16 inch Allen wrench and 9/16 inch wrench, remove the bearing block from the access plate. For accuracy and alignment purposes, the access plate incorporates tapped holes to properly position the capscrews.

5)Position the bearing block on a suitable work surface. A common shop vise can also be utilized. Remove the snap ring that retains the bushing in the bearing bore. FIGURE 45.

6)Position the bearing block on the arbor press with the bearing facing up. Determine that the bearing block is properly supported. Using the arbor press and an appropriate sized thrust bushing, remove the internal hexagon bushing from the bearing. FIGURE 46.

FIGURE 45

8FP FLOOR PLANER SERIES

OPERATION AND PARTS MANUAL REV #2 (05/28/09)

PAGE 37

 

 

 

Image 37
Contents Electric and Gasoline Floor Planers Model 8FP Series Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Application All Models Removing the Floor Planer from the PalletFilling the 8FP/G Series Engine Fuel Tank Flail Design and Application Theory of OperationBeam Flail Star FlailMilling Flail Pentagonal FlailFunction of Spacer Washers Spacer WashersProblems encountered by uneven component wear Flail Drum Design and Application General Notes Regarding Flail Drums Installing Flails on the TWO Section DrumNormal installation procedure for milling flails Installing a Loaded Drum on the Driveshaft General Notes Regarding the Installation of FlailsTransporting the Floor Planer Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Floor Planer on the JOB Site Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Stopping the 8FP/G Series Gasoline Powered Floor Planer Stopping the 8FP/E Series Electrically Powered Floor PlanerPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent Application As Specified Installing a Replacement V-BELT or PulleyAssembly INSTRUCTIONS/OPERATIONS Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Aligning the Caster Wheels Checking Driveshaft RUN OUT Page Engine Service MAINTENANCE/SERVICEApplication 8FP/G Series Floor Planer Troubleshooting Accelerated Bearing Wear AND/OR Failure Accelerated V-BELT WearUneven Cutting Action Storage StorageGeneral FrameExplanation of Code in Remarks Column Qty Description Suggested Spare PartsMain Frame Assy Main Frame AssemblyFRAME, Main Main Frame Assy Part Name QTYTUBE, Vacuum Axle MountDriveshaft Assy Driveshaft AssemblyRING, Retaining External Driveshaft Assy Part Name QTY. RemarksSHEAVE, Driveshaft KEY, SpecialRear Frame Assy Rear Frame AssemblyPIN, Roll 3/16 X 1 Plated Rear Frame Assy Part Name QTY RemarksBUSHING, Connex SHAFT, Hinge PlatedOperator Handle Assy Gasoline Operator Handle Assembly GasolineBARREL, Adjusting BOOT, RubberSWITCH, SHUT-OFF TAP, 22-18 Guage WireGasoline Engine Assy Gasoline Engine AssemblyFRAME, Main GX160KQXC9 ENGINE, Honda 5.5HP Part Name QTY. RemarksDrive Pulley BUSHING, Center HUBOperator Handle Assy Operator Handle Assembly ElectricAdjusting Tube Switch Mount Height Adjustment ScrewHOUSING, Switch SWITCH, ON/OFFElectric Motor Assy Electric Motor AssemblyMotor Plate MOTOR, Electric 5HPRELIEF, Strain NUT, BulklheadONE Section Drum Assy ONE Section Drum AssemblyFlail Drum END CAP ONE Section Drum Assy Part NameFlail Drum ROD WASHER, Lock 1/4TWO Section Drum Assy TWO Section Drum AssemblyFlail Drum 2 Section TWO Section Drum Assy Part NameFlails & Spacer Washers Assy FLAILS, Spacers and Washers AssemblyStar Flail FLAILS, Spacers and Washers Assy Part Name QTYSpacer Washer Beam FlailDecals Decal Warning Flails Decals Part Name QTY RemarksDecal Depth Control Decal MQ LogoEffective February 22 Page HERE’S HOW to GET Help