Multiquip 8FP Series manual Assembly INSTRUCTIONS/OPERATIONS

Page 36

ASSEMBLY INSTRUCTIONS/OPERATIONS

8)Clean and inspect the driveshaft and housing for wear and damage. If any damage is evident, replace the applicable component.

9)Clean the outside bore diameter of the replacement bearing. Apply a suitable amount of anaerobic adhesive/sealant to the outside diameter of the bearing. Press the replacement bearing into the bearing housing until its seats itself against the flange. FIGURE 42.

FIGURE 40

FIGURE 41

9)Position the bearing block on the arbor press with the bearing facing up. Support the inner race of the bearing with an appropriate sized bushing to absorb the thrust created by pressing the driveshaft into the bearing. FIGURE 43.

10)Clean the bearing journal area of the driveshaft with a suitable solvent. Apply a suitable amount of anaerobic adhesive/sealant to the bearing journal area of the driveshaft. Press the driveshaft into the bearing housing until it seats against the bearing. FIGURE 44.

11)Reinstall the snap ring on the driveshaft.

CAUTION

Wear safety glasses and other appropriate safety apparel when removing the snap ring or performing any work with an arbor press. Caution all onlookers about the possibility of flying debris and personal injury.

FIGURE 42

FIGURE 43

8FP FLOOR PLANER SERIES

OPERATION AND PARTS MANUAL REV #2 (05/28/09)

PAGE 36

 

 

 

Image 36
Contents Electric and Gasoline Floor Planers Model 8FP Series Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Removing the Floor Planer from the Pallet Application All ModelsFilling the 8FP/G Series Engine Fuel Tank Theory of Operation Flail Design and ApplicationStar Flail Beam FlailPentagonal Flail Milling FlailSpacer Washers Function of Spacer WashersProblems encountered by uneven component wear Flail Drum Design and Application Installing Flails on the TWO Section Drum General Notes Regarding Flail DrumsNormal installation procedure for milling flails General Notes Regarding the Installation of Flails Installing a Loaded Drum on the DriveshaftTransporting the Floor Planer Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Floor Planer on the JOB Site Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Stopping the 8FP/E Series Electrically Powered Floor Planer Stopping the 8FP/G Series Gasoline Powered Floor PlanerPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent Installing a Replacement V-BELT or Pulley Application As SpecifiedAssembly INSTRUCTIONS/OPERATIONS Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Aligning the Caster Wheels Checking Driveshaft RUN OUT Page MAINTENANCE/SERVICE Engine ServiceApplication 8FP/G Series Floor Planer Troubleshooting Accelerated V-BELT Wear Accelerated Bearing Wear AND/OR FailureUneven Cutting Action Storage StorageFrame GeneralExplanation of Code in Remarks Column Suggested Spare Parts Qty DescriptionMain Frame Assembly Main Frame AssyMain Frame Assy Part Name QTY FRAME, MainTUBE, Vacuum Axle MountDriveshaft Assembly Driveshaft AssyDriveshaft Assy Part Name QTY. Remarks RING, Retaining ExternalSHEAVE, Driveshaft KEY, SpecialRear Frame Assembly Rear Frame AssyRear Frame Assy Part Name QTY Remarks PIN, Roll 3/16 X 1 PlatedBUSHING, Connex SHAFT, Hinge PlatedOperator Handle Assembly Gasoline Operator Handle Assy GasolineBOOT, Rubber BARREL, AdjustingSWITCH, SHUT-OFF TAP, 22-18 Guage WireGasoline Engine Assembly Gasoline Engine AssyPart Name QTY. Remarks FRAME, Main GX160KQXC9 ENGINE, Honda 5.5HPDrive Pulley BUSHING, Center HUBOperator Handle Assembly Electric Operator Handle AssyHeight Adjustment Screw Adjusting Tube Switch MountHOUSING, Switch SWITCH, ON/OFFElectric Motor Assembly Electric Motor AssyMOTOR, Electric 5HP Motor PlateRELIEF, Strain NUT, BulklheadONE Section Drum Assembly ONE Section Drum AssyONE Section Drum Assy Part Name Flail Drum END CAPFlail Drum ROD WASHER, Lock 1/4TWO Section Drum Assembly TWO Section Drum AssyTWO Section Drum Assy Part Name Flail Drum 2 SectionFLAILS, Spacers and Washers Assembly Flails & Spacer Washers AssyFLAILS, Spacers and Washers Assy Part Name QTY Star FlailSpacer Washer Beam FlailDecals Decals Part Name QTY Remarks Decal Warning FlailsDecal Depth Control Decal MQ LogoEffective February 22 Page HERE’S HOW to GET Help