Multiquip 8FP Series manual HERE’S HOW to GET Help

Page 74

OPERATION AND PARTS MANUAL

HERE’S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER ON-HAND WHEN CALLING

UNITED STATES

Multiquip Corporate Office

 

MQ Parts Department

 

18910 Wilmington Ave.

Tel. (800) 421-1244

800-427-1244

Fax: 800-672-7877

Carson, CA 90746

Fax (800) 537-3927

310-537-3700

Fax: 310-637-3284

Contact: mq@multiquip.com

 

 

 

Mayco Parts

 

Warranty Department

 

800-306-2926

Fax: 800-672-7877

800-421-1244, Ext. 279

Fax: 310-537-1173

310-537-3700

Fax: 310-637-3284

310-537-3700, Ext. 279

 

Service Department

 

Technical Assistance

 

800-421-1244

Fax: 310-537-4259

800-478-1244

Fax: 310-631-5032

310-537-3700

 

 

 

 

 

 

 

MEXICO

 

UNITED KINGDOM

 

MQ Cipsa

 

Multiquip (UK) Limited Head Office

Carr. Fed. Mexico-Puebla KM 126.5

Tel: (52) 222-225-9900

Hanover Mill, Fitzroy Street,

Tel: 0161 339 2223

Momoxpan, Cholula, Puebla 72760 Mexico

Fax: (52) 222-285-0420

Ashton-under-Lyne,

Fax: 0161 339 3226

Contact: pmastretta@cipsa.com.mx

 

Lancashire OL7 0TL

 

 

 

Contact: sales@multiquip.co.uk

 

CANADA

 

 

 

Multiquip

 

 

 

4110 Industriel Boul.

Tel: (450) 625-2244

 

 

Laval, Quebec, Canada H7L 6V3

Tel: (877) 963-4411

 

 

Contact: jmartin@multiquip.com

Fax: (450) 625-8664

 

 

© COPYRIGHT 2009, MULTIQUIP INC.

Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.

The information and specifi cations included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifi cations, design or the information published in this publication at any time without notice and without incurring any obligations.

Your Local Dealer is:

Image 74
Contents Electric and Gasoline Floor Planers Model 8FP Series Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Filling the 8FP/G Series Engine Fuel Tank Removing the Floor Planer from the PalletApplication All Models Theory of Operation Flail Design and ApplicationStar Flail Beam FlailPentagonal Flail Milling FlailSpacer Washers Function of Spacer WashersProblems encountered by uneven component wear Flail Drum Design and Application Installing Flails on the TWO Section Drum General Notes Regarding Flail DrumsNormal installation procedure for milling flails General Notes Regarding the Installation of Flails Installing a Loaded Drum on the DriveshaftTransporting the Floor Planer Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Floor Planer on the JOB Site Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Preventative Maintenance Check LIST. Application All Models Stopping the 8FP/E Series Electrically Powered Floor PlanerStopping the 8FP/G Series Gasoline Powered Floor Planer Observe all applicable safety precautions for the solvent Installing a Replacement V-BELT or Pulley Application As SpecifiedAssembly INSTRUCTIONS/OPERATIONS Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Aligning the Caster Wheels Checking Driveshaft RUN OUT Page Application 8FP/G Series Floor Planer MAINTENANCE/SERVICEEngine Service Troubleshooting Uneven Cutting Action Accelerated V-BELT WearAccelerated Bearing Wear AND/OR Failure Storage StorageFrame GeneralExplanation of Code in Remarks Column Suggested Spare Parts Qty DescriptionMain Frame Assembly Main Frame AssyTUBE, Vacuum Main Frame Assy Part Name QTYFRAME, Main Axle MountDriveshaft Assembly Driveshaft AssySHEAVE, Driveshaft Driveshaft Assy Part Name QTY. RemarksRING, Retaining External KEY, SpecialRear Frame Assembly Rear Frame AssyBUSHING, Connex Rear Frame Assy Part Name QTY RemarksPIN, Roll 3/16 X 1 Plated SHAFT, Hinge PlatedOperator Handle Assembly Gasoline Operator Handle Assy GasolineSWITCH, SHUT-OFF BOOT, RubberBARREL, Adjusting TAP, 22-18 Guage WireGasoline Engine Assembly Gasoline Engine AssyDrive Pulley Part Name QTY. RemarksFRAME, Main GX160KQXC9 ENGINE, Honda 5.5HP BUSHING, Center HUBOperator Handle Assembly Electric Operator Handle AssyHOUSING, Switch Height Adjustment ScrewAdjusting Tube Switch Mount SWITCH, ON/OFFElectric Motor Assembly Electric Motor AssyRELIEF, Strain MOTOR, Electric 5HPMotor Plate NUT, BulklheadONE Section Drum Assembly ONE Section Drum AssyFlail Drum ROD ONE Section Drum Assy Part NameFlail Drum END CAP WASHER, Lock 1/4TWO Section Drum Assembly TWO Section Drum AssyTWO Section Drum Assy Part Name Flail Drum 2 SectionFLAILS, Spacers and Washers Assembly Flails & Spacer Washers AssySpacer Washer FLAILS, Spacers and Washers Assy Part Name QTYStar Flail Beam FlailDecals Decal Depth Control Decals Part Name QTY Remarks Decal Warning Flails Decal MQ LogoEffective February 22 Page HERE’S HOW to GET Help