Powermatic 209HH Outfeed Roller Height, Infeed Roller Height, Chipbreaker Height

Page 17

Outfeed Roller Height

1.Disconnect machine from power source.

2.Make sure the knives are set properly as previously explained under "Knife Adjustment."

3.Place the gauge block (J, Figure 26) on the table directly beneath the cutterhead (D, Figure 26).

4.Using a 0.02" (0.5mm) feeler gauge (K, Figure 26) placed on top of the gauge block, raise the work table until the knife just touches the feeler gauge when the knife is at its lowest point. Do not move the work table any further until the outfeed roller is adjusted.

5.Remove the feeler gauge and move the gauge block (J, Figure 27) under one end of the outfeed roller (F, Figure 27). The bottom of the outfeed roller should just touch the top of the gauge block. If an adjustment to the outfeed roller is necessary, loosen the lock nut (L, Figure 27) and turn screw (M, Figure

27)until the outfeed roller just touches the gauge block. Then tighten lock nut (L, Figure

27).

6.Check and adjust the opposite end of the outfeed roller in the same manner.

Infeed Roller Height

Use the exact same procedure for checking the infeed roller as you did for the outfeed roller, except use a .004" (0.1mm) feeler gauge atop the gauge block. If adjustment is necessary, use the lock nut and screw on each end of the infeed roller.

Chipbreaker Height

The chipbreaker breaks off the larger chips before the stock reaches the cutterhead. Use the gauge block and a .004" (0.1mm) feeler gauge to check the height of the chipbreaker, following the same procedure as above. If adjustment is needed:

1.Remove top cover.

2.Loosen the lock nuts (A, Figure 28) at both ends of the chipbreaker, and turn the set screws to raise or lower the chipbreaker as needed. The set screws should be turned the same amount.

3.When the chipbreaker contacts the gauge block, tighten both lock nuts (A, Figure 28).

Figure 26

Figure 27

Figure 28

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Part No. M-0460283 PowermaticWarranty Period Warranty and ServiceTable of Contents Page Page Introduction Features 209HH-3 Specifications209-3 Unpacking Crate Contents FigureHandwheel AssemblyKnife Gauge model 209 only Dust Hood Extension TablesElectrical Connections If converting from 230 to 460 volt operationExtension Cords AdjustmentsBelt Tension Table RollersCutterhead Knife Adjustments Model 209 onlyReplacing and Re-setting Knives Model 209 only Repeated Replacing or Rotating Knife Inserts Model 209HH onlyKnow the Transmitting Rollers of Your Planer Work Table Parallel to CutterheadInfeed and Outfeed Roller Spring Tension Anti-Kickback FingersChipbreaker Height Outfeed Roller HeightInfeed Roller Height Pressure Bar Height Changing Accessories for Lowest Feed SpeedChip Deflector Feed Speed ControlDepth of Cut Return RollersLubrication MaintenanceFigure No Probable Cause Remedy Troubleshooting Operating ProblemsTrouble Troubleshooting Mechanical and Electrical Problems Replacement Parts Optional AccessoriesCutterhead Assembly Index No. Part No Description Size Qty Parts List Cutterhead Assembly100 Base Assembly Parts List Base Assembly Gearbox Assembly Low Speed Gear Kit includes #14-6292779 and #15-6292780 Parts List Gearbox AssemblyStand Assembly Parts List Stand Assembly 209HH-5023FC Parts List Table Assembly Electrical Connections Single Phase, 230 Volt only Electrical Connections 3 Phase, 230 Volt only Electrical Connections 3 Phase, 460 Volt only Checklist for Model 209 and 209HH Planers Preventive MaintenancePage Page Parte Nro. M-0460283 Cepilladora de 20-pulgadasPeríodo de la Garantía Garantía y Servicio TécnicoÍndice Page Page Figura Introducción CaracterísticasEspecificaciones Contenidos de la Caja Figura DesempaqueManivela MontajeGalga de Cuchilla modelo 209 solamente Conexiones Eléctricas Mesas de ExtensiónCubierta Contra el Polvo Cables de extensión AjustesTensión de la Correa Rodillos de MesaAjustes de las Cuchillas Modelo 209 solamente Cabeza de CorteSustitución y Reajuste de las Cuchillas Modelo 209 solamente Figura 20 Modelo 209HH solamente Conozca los Rodillos de Transmisión de su Cepilladora Figura Mesa de Trabajo Paralela a la Cabeza de CorteBloqueadores Antiretroceso Altura del Rompevirutas Altura del Rodillo de SalidaAltura del Rodillo de Entrada Control de la Velocidad de Alimentación Altura de la Barra de PresiónDeflector de Virutas Profundidad de Corte Rodillos de Retorno de MaterialLubricación MantenimientoFigura No Causa Probable Solución Diagnóstico de Problemas Problemas OperativosProblema Diagnóstico de Problemas Problemas Eléctricos y Mecánicos Lista de Partes Accesorios OpcionalesConjunto de Cabeza de Corte Nro. de Lista. Parte Nro Descripción Tamaño Cantidad Lista de Partes Conjunto de la Cabeza de Corte6292636 Conjunto de Base Lista de Partes Conjunto de Base Conjunto de la Caja de Velocidades Lisa de Partes Conjunto de la Caja de Velocidades Conjunto de Gabinete Lista de Partes Conjunto de Gabinete Interruptor Magnético modelo 209 solamente 5HP 1Ø 209-5016BC Lista de Partes Conjunto de Mesa Conexiones Eléctricas Monofásico 230 Voltios solamente Conexiones Eléctricas -Trifásico 230 Voltios solamente Conexiones Eléctricas -Trifásico 460 Voltios solamente Mantenimiento Preventivo Page Page Pièce M-0460283 Raboteuse 20-poucesPériode de garantie Garantie et entretienGraissage Table des matièresPage Page Introduction Caractéristiques 209-1 SpécificationsContenu de la caisse Figure DéballageRoue manuelle MontageCalibre du couteau modèle 209 uniquement Connexions électriques Tables d’extensionCapot anti-poussière Fils de rallonge RéglagesTension de la courroie Rouleaux de tableRéglages du couteau modèle 209 uniquement Tête de la découpeuseRemplacement et nouveau réglage modèle 209 uniquement Répété Connaissez les rouleaux de transmission de votre raboteuse Table de travail parallèle à la tête de la découpeuseTension du ressort du rouleau d’entrée et de sortie Doigts anti-reculHauteur du brise-copeaux Hauteur du rouleau de sortieHauteur du rouleau d’entrée Contrôle de la vitesse d’alimentation Hauteur de la barre de pressionDéflecteur de copeau Profondeur de la coupe Rouleaux de retourLubrifiant DE LA Boîte DE Vitesses GraissagePosition Intervalle Types de lubrifiant appropriés De la Anomalies Diagnostic des anomalies Problèmes fonctionnelsDiagnostic des anomalies Problèmes mécaniques et électriques Pièces de remplacement Accessoires en optionDispositif de la tête de la découpeuse ’indice N de la pièce Description Taille Qté Liste des pièces Dispositif de la tête de la découpeuseX 20 x 3T 6292645 Montage de la base Liste des pièces Dispositif de la base Dispositif de la boîte de vitesses Vis de bouchon de tête de la prise de courant Liste des pièces Dispositif de la boîte de vitessesDispositif du support Liste des pièces Dispositif du support Commutateur magnétique modèle 209HH uniquement5HP 1PH 230V Liste des pièces Dispositif de la table Connexions électriques phase unique, 230 volts uniquement Connexions électriques 3 phases, 230 volts uniquement Connexions électriques 3 phases, 460 volts uniquement Maintenance préventive Page New Sanford Rd LaVergne, TN Téléphone
Related manuals
Manual 40 pages 22.53 Kb

209HH, 209 specifications

The Powermatic 209 and the Powermatic 209HH are two premium models in the range of high-performance drill presses designed for serious woodworkers and metalworkers alike. These machines are lauded for their combination of durability, precision, and innovative features, making them favorable choices in workshops that demand reliable and efficient performance.

One of the standout features of the Powermatic 209 is its robust construction. The machine boasts a heavy-duty cast iron base and column, ensuring stability during operation and reducing vibrations that could affect drilling accuracy. This solid foundation is complemented by a precisely machined table, which can be adjusted for height and angle, allowing for increased flexibility for various drilling applications.

The Powermatic 209 uses a powerful motor that provides ample torque for a variety of materials, from soft woods to tougher metals. The variable speed control feature allows users to easily adjust the spindle speed to match the requirements of the specific operation, accommodating drill bits of different sizes and materials. This adaptability is further enhanced in the 209HH model, which is equipped with an integrated digital RPM readout. This technology provides real-time feedback to the operator, allowing for optimal speed adjustments and ensuring enhanced accuracy.

Another key characteristic of the Powermatic 209 and 209HH is their precision-engineering features. The machines include a laser positioning system, which aids in aligning drill bits with great accuracy on the workpiece. This feature significantly reduces setup time and ensures consistent results, especially on intricate drilling tasks.

Furthermore, both models come with a quick-release table, making it easy to switch between various workpieces. The adjustable quill depth stop is another notable feature, allowing operators to set precise depths for repeated drilling tasks, thus enhancing productivity.

In conclusion, the Powermatic 209 and 209HH drill presses stand out in the marketplace for their combination of robust construction, advanced technology, and precision engineering. These machines not only ensure high-quality results but also bring a level of efficiency and adaptability that is vital for serious craftsmen. Whether in a professional shop or a dedicated home workshop, the Powermatic 209 and 209HH are built to perform and built to last.
Top Page Image Contents