Powermatic 209HH operating instructions Pressure Bar Height, Chip Deflector, Feed Speed Control

Page 18

Pressure Bar Height

The pressure bar prevents the stock from lifting after it passes under the cutterhead. Check the height of the pressure bar with your gauge block and a .008" (0.2mm) feeler gauge. If adjustment is needed:

1.Remove top cover.

2.Loosen the lock nuts (B, Figure 29) on both ends of the pressure bar and turn the set screws as needed.

3.When the pressure bar contacts the top of the gauge block, tighten the lock nuts (B, Figure 29).

Chip Deflector

The chip deflector (C, Figure 29) keeps wood chips from falling into the outfeed roller. The deflector should be set approximately 1/16" from the tip of the knives. Make sure the deflector's front edge is beveled to match the shape of the cutterhead.

Feed Speed Control

Your machine is equipped with a spiral, serrated infeed roller and a solid steel outfeed roller. When the feed rollers are engaged, they turn to feed the stock. The feed rollers slow automatically when the machine is under heavy load for best planing in all conditions. The feed rollers are driven by chains (A, Figure 30) and sprockets (B, Figure 30) which take power directly from the cutterhead through the oil bath gear box (C, Figure 30).

The gear box has two feed speeds. These are set by pulling out or pushing in the shift lever (D, Figure 30) while the machine is running. The feed speed range is shown in Figure 31.

Do not attempt to change feed speed while stock is passing through the machine. Damage to the gearbox may result.

Changing Accessories for Lowest Feed Speed

The lowest feed speeds for your planer (16.2 fpm and 20.7 fpm) can be obtained by replacing the lower (gear shaft) sprocket and its chain (Figure 31).

A low speed gear kit, consisting of a 50P chain and 12T sprocket, is provided with your planer.

To change the sprocket and chain on your machine, proceed as follows:

Figure 29

Figure 30

Figure 31

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Powermatic Part No. M-0460283Warranty and Service Warranty PeriodTable of Contents Page Page Introduction Features Specifications 209-3209HH-3 Crate Contents Figure UnpackingAssembly Knife Gauge model 209 onlyHandwheel Electrical Connections Extension TablesDust Hood If converting from 230 to 460 volt operationBelt Tension AdjustmentsExtension Cords Table RollersKnife Adjustments Model 209 only CutterheadReplacing and Re-setting Knives Model 209 only Replacing or Rotating Knife Inserts Model 209HH only RepeatedWork Table Parallel to Cutterhead Know the Transmitting Rollers of Your PlanerAnti-Kickback Fingers Infeed and Outfeed Roller Spring TensionOutfeed Roller Height Infeed Roller HeightChipbreaker Height Chip Deflector Changing Accessories for Lowest Feed SpeedPressure Bar Height Feed Speed ControlReturn Rollers Depth of CutMaintenance LubricationFigure No Troubleshooting Operating Problems TroubleProbable Cause Remedy Troubleshooting Mechanical and Electrical Problems Optional Accessories Replacement PartsCutterhead Assembly Parts List Cutterhead Assembly Index No. Part No Description Size Qty100 Base Assembly Parts List Base Assembly Gearbox Assembly Parts List Gearbox Assembly Low Speed Gear Kit includes #14-6292779 and #15-6292780Stand Assembly Parts List Stand Assembly 209HH-5023FC Parts List Table Assembly Electrical Connections Single Phase, 230 Volt only Electrical Connections 3 Phase, 230 Volt only Electrical Connections 3 Phase, 460 Volt only Preventive Maintenance Checklist for Model 209 and 209HH PlanersPage Page Cepilladora de 20-pulgadas Parte Nro. M-0460283Garantía y Servicio Técnico Período de la GarantíaÍndice Page Page Introducción Características FiguraEspecificaciones Desempaque Contenidos de la Caja FiguraMontaje Galga de Cuchilla modelo 209 solamenteManivela Mesas de Extensión Cubierta Contra el PolvoConexiones Eléctricas Tensión de la Correa AjustesCables de extensión Rodillos de MesaCabeza de Corte Ajustes de las Cuchillas Modelo 209 solamenteSustitución y Reajuste de las Cuchillas Modelo 209 solamente Figura 20 Modelo 209HH solamente Mesa de Trabajo Paralela a la Cabeza de Corte Conozca los Rodillos de Transmisión de su Cepilladora FiguraBloqueadores Antiretroceso Altura del Rodillo de Salida Altura del Rodillo de EntradaAltura del Rompevirutas Altura de la Barra de Presión Deflector de VirutasControl de la Velocidad de Alimentación Rodillos de Retorno de Material Profundidad de CorteMantenimiento LubricaciónFigura No Diagnóstico de Problemas Problemas Operativos ProblemaCausa Probable Solución Diagnóstico de Problemas Problemas Eléctricos y Mecánicos Accesorios Opcionales Lista de PartesConjunto de Cabeza de Corte Lista de Partes Conjunto de la Cabeza de Corte Nro. de Lista. Parte Nro Descripción Tamaño Cantidad6292636 Conjunto de Base Lista de Partes Conjunto de Base Conjunto de la Caja de Velocidades Lisa de Partes Conjunto de la Caja de Velocidades Conjunto de Gabinete Lista de Partes Conjunto de Gabinete Interruptor Magnético modelo 209 solamente 5HP 1Ø 209-5016BC Lista de Partes Conjunto de Mesa Conexiones Eléctricas Monofásico 230 Voltios solamente Conexiones Eléctricas -Trifásico 230 Voltios solamente Conexiones Eléctricas -Trifásico 460 Voltios solamente Mantenimiento Preventivo Page Page Raboteuse 20-pouces Pièce M-0460283Garantie et entretien Période de garantieTable des matières GraissagePage Page Introduction Caractéristiques Spécifications 209-1Déballage Contenu de la caisse FigureMontage Calibre du couteau modèle 209 uniquementRoue manuelle Tables d’extension Capot anti-poussièreConnexions électriques Tension de la courroie RéglagesFils de rallonge Rouleaux de tableTête de la découpeuse Réglages du couteau modèle 209 uniquementRemplacement et nouveau réglage modèle 209 uniquement Répété Table de travail parallèle à la tête de la découpeuse Connaissez les rouleaux de transmission de votre raboteuseDoigts anti-recul Tension du ressort du rouleau d’entrée et de sortieHauteur du rouleau de sortie Hauteur du rouleau d’entréeHauteur du brise-copeaux Hauteur de la barre de pression Déflecteur de copeauContrôle de la vitesse d’alimentation Rouleaux de retour Profondeur de la coupeGraissage Lubrifiant DE LA Boîte DE VitessesPosition Intervalle Types de lubrifiant appropriés De la Diagnostic des anomalies Problèmes fonctionnels AnomaliesDiagnostic des anomalies Problèmes mécaniques et électriques Accessoires en option Pièces de remplacementDispositif de la tête de la découpeuse Liste des pièces Dispositif de la tête de la découpeuse ’indice N de la pièce Description Taille QtéX 20 x 3T 6292645 Montage de la base Liste des pièces Dispositif de la base Dispositif de la boîte de vitesses Liste des pièces Dispositif de la boîte de vitesses Vis de bouchon de tête de la prise de courantDispositif du support Liste des pièces Dispositif du support Commutateur magnétique modèle 209HH uniquement5HP 1PH 230V Liste des pièces Dispositif de la table Connexions électriques phase unique, 230 volts uniquement Connexions électriques 3 phases, 230 volts uniquement Connexions électriques 3 phases, 460 volts uniquement Maintenance préventive Page New Sanford Rd LaVergne, TN Téléphone
Related manuals
Manual 40 pages 22.53 Kb

209HH, 209 specifications

The Powermatic 209 and the Powermatic 209HH are two premium models in the range of high-performance drill presses designed for serious woodworkers and metalworkers alike. These machines are lauded for their combination of durability, precision, and innovative features, making them favorable choices in workshops that demand reliable and efficient performance.

One of the standout features of the Powermatic 209 is its robust construction. The machine boasts a heavy-duty cast iron base and column, ensuring stability during operation and reducing vibrations that could affect drilling accuracy. This solid foundation is complemented by a precisely machined table, which can be adjusted for height and angle, allowing for increased flexibility for various drilling applications.

The Powermatic 209 uses a powerful motor that provides ample torque for a variety of materials, from soft woods to tougher metals. The variable speed control feature allows users to easily adjust the spindle speed to match the requirements of the specific operation, accommodating drill bits of different sizes and materials. This adaptability is further enhanced in the 209HH model, which is equipped with an integrated digital RPM readout. This technology provides real-time feedback to the operator, allowing for optimal speed adjustments and ensuring enhanced accuracy.

Another key characteristic of the Powermatic 209 and 209HH is their precision-engineering features. The machines include a laser positioning system, which aids in aligning drill bits with great accuracy on the workpiece. This feature significantly reduces setup time and ensures consistent results, especially on intricate drilling tasks.

Furthermore, both models come with a quick-release table, making it easy to switch between various workpieces. The adjustable quill depth stop is another notable feature, allowing operators to set precise depths for repeated drilling tasks, thus enhancing productivity.

In conclusion, the Powermatic 209 and 209HH drill presses stand out in the marketplace for their combination of robust construction, advanced technology, and precision engineering. These machines not only ensure high-quality results but also bring a level of efficiency and adaptability that is vital for serious craftsmen. Whether in a professional shop or a dedicated home workshop, the Powermatic 209 and 209HH are built to perform and built to last.
Top Page Image Contents