Powermatic 209HH operating instructions

Page 5

Hand safety. Keep hands outside the machine. NEVER reach under the guards to try to clear stock that stops feeding. Do not clear chips and sawdust with hands; use a brush. Do not have any part of the hands under that part of the board that is over the table when starting a cut; the infeed roll will engage the board and force it down against the table causing a pinching action. Do not operate machine while the gear cover is open.

Cutterhead rotation: Be sure cutterhead rotates under power in a counterclockwise direction when viewed from the main drive motor side.

Material condition: Do not plane boards with loose knots or with nails or any foreign material on its surface. Knife impact on these objects can cause the knives to be pulled out and cause them to shatter against the chipbreaker or pressure bar. Twisted, warped, or in wind stock should first be jointed on one surface before attempting to plane a parallel surface on the planer. Serious stock flaws cannot be removed by use of a planer alone.

Machine adjustments: Make all machine adjustments with power off except feed rate.

Job completion. If the operator leaves the machine area for any reason, the planer should be turned "off" and the cutterhead should come to a complete stop before his departure. In addition, if the operation is complete, he should clean the planer and the work area. Never clean the planer with power "on" and never use the hands to clear sawdust and debris; use a brush.

Replacement parts. Use only Powermatic or factory authorized replacement parts and accessories; otherwise the warranty and guarantee is null and void.

Misuse. Do not use this planer for other than its intended use. If used for other purposes, Powermatic disclaims any real or implied warranty and holds itself harmless for any injury or damage which may result from that use.

If you are not thoroughly familiar with the operation of planers, obtain advice from your supervisor, instructor or other qualified person.

Drugs, alcohol, medication. Do not operate this machine while under the influence of drugs, alcohol, or any medication.

Health hazards. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

*Lead from lead-based paint.

*Crystalline silica from bricks and cement and other masonry products.

*Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specifically designed to filter out microscopic particles.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly even death.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Part No. M-0460283 PowermaticWarranty Period Warranty and ServiceTable of Contents Page Page Introduction Features 209HH-3 Specifications209-3 Unpacking Crate Contents FigureHandwheel AssemblyKnife Gauge model 209 only Dust Hood Extension TablesElectrical Connections If converting from 230 to 460 volt operationExtension Cords AdjustmentsBelt Tension Table RollersCutterhead Knife Adjustments Model 209 onlyReplacing and Re-setting Knives Model 209 only Repeated Replacing or Rotating Knife Inserts Model 209HH onlyKnow the Transmitting Rollers of Your Planer Work Table Parallel to CutterheadInfeed and Outfeed Roller Spring Tension Anti-Kickback FingersChipbreaker Height Outfeed Roller HeightInfeed Roller Height Pressure Bar Height Changing Accessories for Lowest Feed SpeedChip Deflector Feed Speed ControlDepth of Cut Return RollersLubrication MaintenanceFigure No Probable Cause Remedy Troubleshooting Operating ProblemsTrouble Troubleshooting Mechanical and Electrical Problems Replacement Parts Optional AccessoriesCutterhead Assembly Index No. Part No Description Size Qty Parts List Cutterhead Assembly100 Base Assembly Parts List Base Assembly Gearbox Assembly Low Speed Gear Kit includes #14-6292779 and #15-6292780 Parts List Gearbox AssemblyStand Assembly Parts List Stand Assembly 209HH-5023FC Parts List Table Assembly Electrical Connections Single Phase, 230 Volt only Electrical Connections 3 Phase, 230 Volt only Electrical Connections 3 Phase, 460 Volt only Checklist for Model 209 and 209HH Planers Preventive MaintenancePage Page Parte Nro. M-0460283 Cepilladora de 20-pulgadasPeríodo de la Garantía Garantía y Servicio TécnicoÍndice Page Page Figura Introducción CaracterísticasEspecificaciones Contenidos de la Caja Figura DesempaqueManivela MontajeGalga de Cuchilla modelo 209 solamente Conexiones Eléctricas Mesas de ExtensiónCubierta Contra el Polvo Cables de extensión AjustesTensión de la Correa Rodillos de MesaAjustes de las Cuchillas Modelo 209 solamente Cabeza de CorteSustitución y Reajuste de las Cuchillas Modelo 209 solamente Figura 20 Modelo 209HH solamente Conozca los Rodillos de Transmisión de su Cepilladora Figura Mesa de Trabajo Paralela a la Cabeza de CorteBloqueadores Antiretroceso Altura del Rompevirutas Altura del Rodillo de SalidaAltura del Rodillo de Entrada Control de la Velocidad de Alimentación Altura de la Barra de PresiónDeflector de Virutas Profundidad de Corte Rodillos de Retorno de MaterialLubricación MantenimientoFigura No Causa Probable Solución Diagnóstico de Problemas Problemas OperativosProblema Diagnóstico de Problemas Problemas Eléctricos y Mecánicos Lista de Partes Accesorios OpcionalesConjunto de Cabeza de Corte Nro. de Lista. Parte Nro Descripción Tamaño Cantidad Lista de Partes Conjunto de la Cabeza de Corte6292636 Conjunto de Base Lista de Partes Conjunto de Base Conjunto de la Caja de Velocidades Lisa de Partes Conjunto de la Caja de Velocidades Conjunto de Gabinete Lista de Partes Conjunto de Gabinete Interruptor Magnético modelo 209 solamente 5HP 1Ø 209-5016BC Lista de Partes Conjunto de Mesa Conexiones Eléctricas Monofásico 230 Voltios solamente Conexiones Eléctricas -Trifásico 230 Voltios solamente Conexiones Eléctricas -Trifásico 460 Voltios solamente Mantenimiento Preventivo Page Page Pièce M-0460283 Raboteuse 20-poucesPériode de garantie Garantie et entretienGraissage Table des matièresPage Page Introduction Caractéristiques 209-1 SpécificationsContenu de la caisse Figure DéballageRoue manuelle MontageCalibre du couteau modèle 209 uniquement Connexions électriques Tables d’extensionCapot anti-poussière Fils de rallonge RéglagesTension de la courroie Rouleaux de tableRéglages du couteau modèle 209 uniquement Tête de la découpeuseRemplacement et nouveau réglage modèle 209 uniquement Répété Connaissez les rouleaux de transmission de votre raboteuse Table de travail parallèle à la tête de la découpeuseTension du ressort du rouleau d’entrée et de sortie Doigts anti-reculHauteur du brise-copeaux Hauteur du rouleau de sortieHauteur du rouleau d’entrée Contrôle de la vitesse d’alimentation Hauteur de la barre de pressionDéflecteur de copeau Profondeur de la coupe Rouleaux de retourLubrifiant DE LA Boîte DE Vitesses GraissagePosition Intervalle Types de lubrifiant appropriés De la Anomalies Diagnostic des anomalies Problèmes fonctionnelsDiagnostic des anomalies Problèmes mécaniques et électriques Pièces de remplacement Accessoires en optionDispositif de la tête de la découpeuse ’indice N de la pièce Description Taille Qté Liste des pièces Dispositif de la tête de la découpeuseX 20 x 3T 6292645 Montage de la base Liste des pièces Dispositif de la base Dispositif de la boîte de vitesses Vis de bouchon de tête de la prise de courant Liste des pièces Dispositif de la boîte de vitessesDispositif du support Liste des pièces Dispositif du support Commutateur magnétique modèle 209HH uniquement5HP 1PH 230V Liste des pièces Dispositif de la table Connexions électriques phase unique, 230 volts uniquement Connexions électriques 3 phases, 230 volts uniquement Connexions électriques 3 phases, 460 volts uniquement Maintenance préventive Page New Sanford Rd LaVergne, TN Téléphone
Related manuals
Manual 40 pages 22.53 Kb

209HH, 209 specifications

The Powermatic 209 and the Powermatic 209HH are two premium models in the range of high-performance drill presses designed for serious woodworkers and metalworkers alike. These machines are lauded for their combination of durability, precision, and innovative features, making them favorable choices in workshops that demand reliable and efficient performance.

One of the standout features of the Powermatic 209 is its robust construction. The machine boasts a heavy-duty cast iron base and column, ensuring stability during operation and reducing vibrations that could affect drilling accuracy. This solid foundation is complemented by a precisely machined table, which can be adjusted for height and angle, allowing for increased flexibility for various drilling applications.

The Powermatic 209 uses a powerful motor that provides ample torque for a variety of materials, from soft woods to tougher metals. The variable speed control feature allows users to easily adjust the spindle speed to match the requirements of the specific operation, accommodating drill bits of different sizes and materials. This adaptability is further enhanced in the 209HH model, which is equipped with an integrated digital RPM readout. This technology provides real-time feedback to the operator, allowing for optimal speed adjustments and ensuring enhanced accuracy.

Another key characteristic of the Powermatic 209 and 209HH is their precision-engineering features. The machines include a laser positioning system, which aids in aligning drill bits with great accuracy on the workpiece. This feature significantly reduces setup time and ensures consistent results, especially on intricate drilling tasks.

Furthermore, both models come with a quick-release table, making it easy to switch between various workpieces. The adjustable quill depth stop is another notable feature, allowing operators to set precise depths for repeated drilling tasks, thus enhancing productivity.

In conclusion, the Powermatic 209 and 209HH drill presses stand out in the marketplace for their combination of robust construction, advanced technology, and precision engineering. These machines not only ensure high-quality results but also bring a level of efficiency and adaptability that is vital for serious craftsmen. Whether in a professional shop or a dedicated home workshop, the Powermatic 209 and 209HH are built to perform and built to last.
Top Page Image Contents