Miller Electric 625 manual Xxxx, Ready

Page 27

TIME AMPERAGE

XXXX XXXX

Ready

SELECT

ADJUST

TIME AMPERAGE

STUD COUNT

READY

OUTPUT ON

Amperage Adjustment - Push select button once. Returns to “Ready” dis- play in six seconds after adjustment.

XXXX

STUD COUNT

READY

OUTPUT ON

Time Adjustment - Push select but- ton twice. Returns to “Ready” display in six seconds after adjustment.

Stud Count - Push select button three times. Returns to “Ready” dis- play in two seconds.

SELECT

ADJUST

TIME AMPERAGE

XXXX

SELECT ADJUST

TIME AMPERAGE

SCXX XXXX

SELECT ADJUST

STUD COUNT

READY

OUTPUT ON

STUD COUNT

READY

OUTPUT ON

OM-216 244 Page 23

Image 27

Contents File Stud Welding SW OM-216 244JProcess DescriptionFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéSpecifications − IntroductionDuty Cycle And Overheating Location − Installation Power SourceDimensions And Weight Selecting a LocationMin Grounding Conductor Size In AWG Electrical Service GuideHz Three Phase Input VoltageOutput Receptacles Turn off power before connecting to weld output terminalsWeld Output Receptacles And Selecting Cable Sizes ARC Welding can cause Electromagnetic Interference= GND/PE Earth Ground Tools Needed Connecting 3-Phase Input PowerSocket Information Circuit BreakerPin Receptacle Information Rack Mounting− Installation Stud GUN Chuck InstallationChuck Removal Leg Installation Foot and Leg SetupFerrule Grip / Spark Shield Removal and Installation Foot InstallationFoot Alignment Connecting Stud Gun and Work Clamp to Power SourceConnecting Weld Cable and Work Ground Cable Connecting Control CablePlunge Adjustment PlungeStud Welding Measuring LIft Adjusting Stud LiftLIft Adjustment Table Adjusting Lift Front Panel Controls − Operation Power SourceMaterial Thickness Reference Chart Time/Amperage Control Select TIME/AMP AdjustmentReady XxxxStud Welding Procedures − Operation Stud GUNStud Gun Tool Functions Welding Sequence Recommended Settings− Maintenance & Troubleshooting Do not remove case when blowing out inside of unitBlowing Out Inside Of Unit OM-216 244 Disassembly / Assembly Procedures Maintenance Procedures for Stud GunWhen is Maintenance Required? Maintenance StepsTools Needed OM-216 244 Troubleshooting Power Source Troubleshooting Help AidsTroubleshooting Stud Gun But no weldFree play OM-216 244 Circuit Diagram For 460/575 Volt Models − Electrical DiagramsParts Assembly − Parts List for Power SourceDia Part Description Quantity Mkgs 207 SOCKET/WRENCH Selection Table Standard Metric − Parts List for Stud GUN 217 Plunge Dampener Soft Standard W/Dampener Model Table For Chucks and Grips − Options and AccessoriesPlunge Dampener Table For Foot and LegsWork like a Pro Material Thickness Gauge Support ServiceMiller Electric Mfg. Co Owner’s Record