Miller Electric 625 manual Connecting 3-Phase Input Power, = GND/PE Earth Ground Tools Needed

Page 17

4-4. Connecting 3-Phase Input Power

3

= GND/PE Earth Ground

4

7

2

 

 

L1

 

3

 

L2

5

 

6

L3

 

 

 

 

1

1

Tools Needed:

YInstallation must meet all National and Local Codes − have only quali- fied persons make this installation.

YDisconnect and lockout/tagout in- put power before connecting input conductors from unit.

YAlways connect green or green/ yellow conductor to supply grounding terminal first, and nev- er to a line terminal.

.The Auto-Link circuitry in this unit au- tomatically adapts the power source to the primary voltage being applied. Check input voltage available at site. This unit can be connected to any in- put power between 480 or 575 VAC without removing cover to relink the power source.

1Input Power Cord.

2Disconnect Device (switch shown in the OFF position)

3Green Or Green/Yellow Grounding Conductor

4Disconnect Device Grounding Terminal

5Input Conductors (L1, L2 And L3)

6Disconnect Device Line Terminals

Connect green or green/yellow grounding conductor to disconnect device grounding terminal first.

Connect input conductors L1, L2, and L3 to disconnect device line terminals.

7 Overcurrent Protection

Select type and size of overcurrent protec- tion using Section 4-2(fused disconnect switch shown).

Close and secure door on disconnect device. Remove lockout/tagout device, and place switch in the On position.

2/04 - Ref. 802 136-A

OM-216 244 Page 13

Image 17
Contents Process OM-216 244JDescription File Stud Welding SWFrom Miller to You Table of Contents Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéDuty Cycle And Overheating Specifications− Introduction Dimensions And Weight − Installation Power SourceSelecting a Location LocationHz Three Phase Electrical Service GuideInput Voltage Min Grounding Conductor Size In AWGWeld Output Receptacles And Selecting Cable Sizes Turn off power before connecting to weld output terminalsARC Welding can cause Electromagnetic Interference Output Receptacles= GND/PE Earth Ground Tools Needed Connecting 3-Phase Input PowerPin Receptacle Information Circuit BreakerRack Mounting Socket InformationChuck Removal − Installation Stud GUNChuck Installation Ferrule Grip / Spark Shield Removal and Installation Foot and Leg SetupFoot Installation Leg InstallationConnecting Weld Cable and Work Ground Cable Connecting Stud Gun and Work Clamp to Power SourceConnecting Control Cable Foot AlignmentStud Welding Plunge AdjustmentPlunge LIft Adjustment Table Adjusting Stud LiftAdjusting Lift Measuring LIftFront Panel Controls − Operation Power SourceMaterial Thickness Reference Chart Time/Amperage Control Select TIME/AMP AdjustmentReady XxxxStud Gun Tool Functions Stud Welding Procedures− Operation Stud GUN Welding Sequence Recommended SettingsBlowing Out Inside Of Unit − Maintenance & TroubleshootingDo not remove case when blowing out inside of unit OM-216 244 When is Maintenance Required? Maintenance Procedures for Stud GunMaintenance Steps Disassembly / Assembly ProceduresTools Needed OM-216 244 Troubleshooting Power Source Troubleshooting Help AidsFree play Troubleshooting Stud GunBut no weld OM-216 244 Circuit Diagram For 460/575 Volt Models − Electrical DiagramsParts Assembly − Parts List for Power SourceDia Part Description Quantity Mkgs 207 SOCKET/WRENCH Selection Table Standard Metric − Parts List for Stud GUN 217 Plunge Dampener Soft Standard W/Dampener Model Plunge Dampener − Options and AccessoriesTable For Foot and Legs Table For Chucks and GripsWork like a Pro Material Thickness Gauge Support ServiceMiller Electric Mfg. Co Owner’s Record