Miller Electric XMC 4000 manual Effective January 1

Page 43

Effective January 1, 2006

This limited warranty supersedes all previous Miller warranties and is exclusive with no other

guarantees or warranties expressed or implied.

LIMITED WARRANTY − Subject to the terms and conditions below, ITW Welding Products Italy S.r.l., warrants to its original retail purchaser that new Miller equipment sold after the effective date of this limited warranty is free of defects in material and workmanship at the time it is shipped by Miller.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

Within the warranty periods listed below, Miller will repair or replace any warranted parts or components that fail due to such defects in material or workmanship. Miller must be notified in writing within thirty (30) days of such defect or failure, at which time Miller will provide instructions on the warranty claim procedures to be followed.

Miller shall honor warranty claims on warranted equipment listed below in the event of such a failure within the warranty time periods. All warranty time periods start on the date that the equipment was delivered to the original retail purchaser, or one year after the equipment is sent to a European distributor or eighteen months after the equipment is sent to an International distributor.

1.5 Years Parts − 3 Years Labor

*Original main power rectifiers

*Inverters (input and output rectifiers only)

2.3 Years — Parts and Labor

*Transformer/Rectifier Power Sources

*Plasma Arc Cutting Power Sources

*Semi-Automatic and Automatic Wire Feeders

*Inverter Power Sources (unless otherwise stated)

*Water Coolant Systems (integrated)

*Intellitig

*Maxstar 150

*Engine Driven Welding Generators

(NOTE: Engines are warranted separately by the engine manufacturer.)

3.2 year − Parts and Labor (Panther only)

*Hydramate 1&2 Water Cooling Unit

4.1 year − Parts and Labor unless specified

*DC 253 & 403 Rectifier (April 06>)

*Migmatic 171 (April 06>)

*Motor Driven Guns (w/exception of Spoolguns)

*Process Controllers

*Positioners and Controllers

*Automatic Motion Devices

*RFCS Foot Controls

*IHPS Power Sources and Coolers

*Water Coolant Systems (non−integrated)

*Flowgauge and Flowmeter Regulators (No Labor)

*HF Units

*Grids

*Spot Welders

*Load Banks

*Arc Stud power sources and Arc Stud guns

*Running Gear/Trailers

*Plasma Cutting Torches (except APT & SAF Models)

*Field Options

(NOTE: Field options are covered under True Bluefor the remaining warranty period of the product they are installed in, or for a minimum of one year — whichever is greater.)

5 6 Months — Batteries

6.90 Days — Parts

*MIG Guns/TIG Torches

*Induction heating coils and blankets

*APT Model Plasma Cutting Torches

*Remote Controls

*Accessory Kits

*Replacement Parts (No labor)

*Spoolmate Spoolguns

*Canvas covers

Miller’s True BlueLimited Warranty shall not apply to:

1.Consumable components; such as contact tips, cutting nozzles, contactors, brushes, slip rings, relays or parts that fail due to normal wear.

2.Items furnished by Miller, but manufactured by others, such as engines or trade accessories. These items are covered by the manufacturer’s warranty, if any.

3.Equipment that has been modified by any party other than Miller, or equipment that has been improperly installed, improperly operated or misused based upon industry standards, or equipment which has not had reasonable and necessary maintenance, or equipment which has been used for operation outside of the specifications for the equipment.

MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS TRAINED AND EXPERIENCED IN THE USE AND MAINTENANCE OF WELDING EQUIPMENT.

In the event of a warranty claim covered by this warranty, the exclusive remedies shall be, at Miller’s option: (1) repair; or

(2)replacement; or, where authorized in writing by Miller in appropriate cases, (3) the reasonable cost of repair or replacement at an authorized Miller service station; or (4) payment of or credit for the purchase price (less reasonable depreciation based upon actual use) upon return of the goods at customer’s risk and expense. Miller’s option of repair or replacement will be F.O.B., Factory at ITW Welding Products Group Europe, or F.O.B. at a Miller authorized service facility as determined by Miller. Therefore no compensation or reimbursement for transportation costs of any kind will be allowed.

TO THE EXTENT PERMITTED BY LAW, THE REMEDIES PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL Miller BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY OTHER LEGAL THEORY.

ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED BY MILLER.

Some states in the U.S.A. do not allow limitations of how long an implied warranty lasts, or the exclusion of incidental, indirect, special or consequential damages, so the above limitation or exclusion may not apply to you. This warranty provides specific legal rights, and other rights may be available, but may vary from state to state.

In Canada, legislation in some provinces provides for certain additional warranties or remedies other than as stated herein, and to the extent that they may not be waived, the limitations and exclusions set out above may not apply. This Limited Warranty provides specific legal rights, and other rights may be available, but may vary from province to province.

milan_warr 1/06

Image 43
Contents XMC R4000 From Miller to You Indice − Maintenance & TroubleshootingDeclaration of Conformity for European Community CE Products Arc Welding Hazards Symbol UsageMarks a special safety message Means Note not safety relatedMagnetic Fields can affect pacemakers ARC Rays can burn eyes and skinFire or Explosion hazard California Proposition 65 WarningsEMF Information Principal Safety StandardsAbout Pacemakers Manufacturer’s Warning Label Definitions − Definitions60 s 100 h. std I1max Manufacturer’s Rating Labels Symbols And DefinitionsI1eff Specifications − InstallationDuty Cycle And Overheating Volt-Ampere Curves CC ModeLocation Dimensions And WeightMovement Do not move or operate unit where it could tip Selecting a LocationARC Welding can cause Electromagnetic Interference Ground connectorWeld Output Terminals And Selecting Cable Sizes Remote 7 Receptacle InformationCircuit Breakers Operating cooler when coolantFilling Coolant Tank = GND/PE Electrical Service GuideConnecting Input Power 50/60 Hz Three PhaseFront Panel Controls − OperationWelding Process Selection Switching On the Unit and Recalling Factory ParametersBe aware that the wire type selection is Always check and set a trigger mode Trigger Mode SelectionWelding arc. Front panel Jog is recom- mended Jog And Purge SelectionPurge is used to remove impurities Setup Push Button And Advanced Programming Setting And Using Weld Parameters From MemorySetting Menu Type Preparing Unit For MIG Welding Setting InductanceSelecting Manual MIG Welding Preparing Unit For Synergic MIG Welding Manual MIG Welding Advanced SettingsWire Feed Speed Unit only in Menu Synergic MIG Welding Advanced SettingsSetting Pre−Gas only in Menu Full Level Trigger Mode Preparing Unit For Synergic Pulsed MIG Welding Higher inductance setting produces aWire Feed Speed Unit only in Menu Full Synergic Pulsed MIG Welding Advanced SettingsSetting Synergic Double Pulsed MIG Welding Preparing Unit For TIG Welding TIG Welding Advanced SettingsSetting Initial And Final Amperage Setting PostflowLift-Arc Start Stick Welding Advanced SettingsTIG Lift-Arc Welding Preparing Unit For Stick WeldingDo not remove case when blowing out inside of unit − Maintenance & TroubleshootingBlowing Out Inside Of Unit Circuit Breakers CB7 And CB10 Software problems TroubleshootingIs displayed Help Displays HelpHelp Unit. All circuitry referred to is located inside the unit− Electrical Diagram Unit Outer Assembly − Parts ListDia Part Description Quantity Mkgs Unit Main Assembly WCP Page Effective January 1 ITW Welding Products Italy S.r.l. Via Privata Iseo, 6/E Owner’s Record

XMC 4000 specifications

The Miller Electric XMC 4000 is a versatile and robust portable welding machine designed to meet the needs of skilled welders across various industries. With a focus on innovation and performance, the XMC 4000 combines advanced technologies with user-friendly features, making it an ideal choice for both experienced professionals and newcomers to the welding field.

One of the standout features of the XMC 4000 is its exceptional welding output. The machine is capable of delivering a maximum output of 400 amps, allowing it to handle a wide range of applications, from light fabrication to heavy-duty industrial tasks. Its multi-process capabilities enable users to perform MIG, TIG, Stick, and Flux-Cored welding, providing versatility and flexibility for different welding requirements.

The XMC 4000 is equipped with Miller's Auto-Set feature, which simplifies the welding process. This technology automatically adjusts the settings based on the user's selected material thickness and wire diameter, ensuring optimal arcs and reducing the likelihood of operator error. Additionally, the machine includes a built-in dynamic arc control that improves arc stability and provides a consistent weld quality, even in challenging conditions.

Another key characteristic of the XMC 4000 is its user-friendly interface, featuring a large LCD display that provides real-time data on welding parameters. This allows operators to make quick adjustments as needed, enhancing productivity and efficiency on the job site. The intuitive design also makes it easy for users to navigate through various settings without extensive training.

Durability is a priority with the XMC 4000. The unit is built with high-quality materials and designed to withstand harsh working environments. Its rugged construction, combined with a compact and lightweight design, makes it easy to transport, whether to the job site or between service locations.

In terms of power options, the XMC 4000 is adaptable to various input voltages, allowing it to operate seamlessly in both industrial and field-based applications. This level of flexibility means that welders can use it in diverse locations, making it a reliable companion for on-the-go projects.

Overall, the Miller Electric XMC 4000 stands out as a powerful, versatile, and user-friendly welding machine that meets the demands of today’s welding professionals. Its advanced features, durable design, and multiple process capabilities make it an excellent investment for anyone looking to enhance their welding capabilities.