Miller Electric XMC 4000 ARC Rays can burn eyes and skin, Magnetic Fields can affect pacemakers

Page 6

ARC RAYS can burn eyes and skin.

Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld.

DWear an approved welding helmet fitted with a proper shade of fil- ter lenses to protect your face and eyes when welding or watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards).

DWear approved safety glasses with side shields under your helmet.

DUse protective screens or barriers to protect others from flash, glare and sparks; warn others not to watch the arc.

DWear protective clothing made from durable, flame-resistant mate- rial (leather, heavy cotton, or wool) and foot protection.

WELDING can cause fire or explosion.

Welding on closed containers, such as tanks, drums, or pipes, can cause them to blow up. Sparks can fly off from the welding arc. The flying sparks, hot workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause sparks, explosion, overheating, or fire. Check and be sure the area is safe before doing any welding.

DRemove all flammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with approved covers.

DDo not weld where flying sparks can strike flammable material.

DProtect yourself and others from flying sparks and hot metal.

DBe alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas.

DWatch for fire, and keep a fire extinguisher nearby.

DBe aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.

DDo not weld on closed containers such as tanks, drums, or pipes, unless they are properly prepared according to AWS F4.1 (see Safety Standards).

DConnect work cable to the work as close to the welding area as practical to prevent welding current from traveling long, possibly unknown paths and causing electric shock, sparks, and fire hazards.

DDo not use welder to thaw frozen pipes.

DRemove stick electrode from holder or cut off welding wire at contact tip when not in use.

DWear oil-free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes, and a cap.

DRemove any combustibles, such as a butane lighter or matches, from your person before doing any welding.

DFollow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL can injure eyes.

DWelding, chipping, wire brushing, and grinding cause sparks and flying metal. As welds cool, they can throw off slag.

DWear approved safety glasses with side shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

DShut off shielding gas supply when not in use.

D Always ventilate confined spaces or use approved air-supplied respirator.

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

DAllow cooling period before working on gun or

torch.

DTo handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.

MAGNETIC FIELDS can affect pacemakers.

D Pacemaker wearers keep away.

D Wearers should consult their doctor before going near arc welding, gouging, or spot welding operations.

NOISE can damage hearing.

Noise from some processes or equipment can damage hearing.

DWear approved ear protection if noise level is high.

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas cylinders are normally part of the welding process, be sure to treat them carefully.

DProtect compressed gas cylinders from excessive heat, mechani- cal shocks, physical damage, slag, open flames, sparks, and arcs.

DInstall cylinders in an upright position by securing to a stationary support or cylinder rack to prevent falling or tipping.

DKeep cylinders away from any welding or other electrical circuits.

DNever drape a welding torch over a gas cylinder.

DNever allow a welding electrode to touch any cylinder.

DNever weld on a pressurized cylinder − explosion will result.

DUse only correct shielding gas cylinders, regulators, hoses, and fit- tings designed for the specific application; maintain them and associated parts in good condition.

DTurn face away from valve outlet when opening cylinder valve.

DKeep protective cap in place over valve except when cylinder is in use or connected for use.

DUse the right equipment, correct procedures, and sufficient num- ber of persons to lift and move cylinders.

DRead and follow instructions on compressed gas cylinders, associated equipment, and Compressed Gas Association (CGA) publication P-1 listed in Safety Standards.

OM-221 694 Page 2

Page 5 Page 7
Image 6
Page 5 Page 7
Contents XMC R4000 From Miller to You − Maintenance & Troubleshooting IndiceDeclaration of Conformity for European Community CE Products Means Note not safety related Symbol UsageMarks a special safety message Arc Welding HazardsARC Rays can burn eyes and skin Magnetic Fields can affect pacemakersCalifornia Proposition 65 Warnings Fire or Explosion hazardPrincipal Safety Standards EMF InformationAbout Pacemakers − Definitions Manufacturer’s Warning Label Definitions60 s 100 h. std Manufacturer’s Rating Labels Symbols And Definitions I1maxI1eff − Installation SpecificationsDuty Cycle And Overheating CC Mode Volt-Ampere CurvesSelecting a Location Dimensions And WeightMovement Do not move or operate unit where it could tip LocationRemote 7 Receptacle Information Ground connectorWeld Output Terminals And Selecting Cable Sizes ARC Welding can cause Electromagnetic InterferenceOperating cooler when coolant Circuit BreakersFilling Coolant Tank 50/60 Hz Three Phase Electrical Service GuideConnecting Input Power = GND/PE− Operation Front Panel ControlsSwitching On the Unit and Recalling Factory Parameters Welding Process SelectionBe aware that the wire type selection is Trigger Mode Selection Always check and set a trigger modeJog And Purge Selection Welding arc. Front panel Jog is recom- mendedPurge is used to remove impurities Setting And Using Weld Parameters From Memory Setup Push Button And Advanced ProgrammingSetting Menu Type Setting Inductance Preparing Unit For MIG WeldingSelecting Manual MIG Welding Manual MIG Welding Advanced Settings Preparing Unit For Synergic MIG WeldingSynergic MIG Welding Advanced Settings Wire Feed Speed Unit only in MenuSetting Pre−Gas only in Menu Full Level Trigger Mode Higher inductance setting produces a Preparing Unit For Synergic Pulsed MIG WeldingSynergic Pulsed MIG Welding Advanced Settings Wire Feed Speed Unit only in Menu FullSetting Synergic Double Pulsed MIG Welding Setting Postflow TIG Welding Advanced SettingsSetting Initial And Final Amperage Preparing Unit For TIG WeldingPreparing Unit For Stick Welding Stick Welding Advanced SettingsTIG Lift-Arc Welding Lift-Arc Start− Maintenance & Troubleshooting Do not remove case when blowing out inside of unitBlowing Out Inside Of Unit Circuit Breakers CB7 And CB10 Troubleshooting Software problemsIs displayed Help Help DisplaysUnit. All circuitry referred to is located inside the unit Help− Electrical Diagram − Parts List Unit Outer AssemblyDia Part Description Quantity Mkgs Unit Main Assembly WCP Page Effective January 1 Owner’s Record ITW Welding Products Italy S.r.l. Via Privata Iseo, 6/E

XMC 4000 specifications

The Miller Electric XMC 4000 is a versatile and robust portable welding machine designed to meet the needs of skilled welders across various industries. With a focus on innovation and performance, the XMC 4000 combines advanced technologies with user-friendly features, making it an ideal choice for both experienced professionals and newcomers to the welding field.

One of the standout features of the XMC 4000 is its exceptional welding output. The machine is capable of delivering a maximum output of 400 amps, allowing it to handle a wide range of applications, from light fabrication to heavy-duty industrial tasks. Its multi-process capabilities enable users to perform MIG, TIG, Stick, and Flux-Cored welding, providing versatility and flexibility for different welding requirements.

The XMC 4000 is equipped with Miller's Auto-Set feature, which simplifies the welding process. This technology automatically adjusts the settings based on the user's selected material thickness and wire diameter, ensuring optimal arcs and reducing the likelihood of operator error. Additionally, the machine includes a built-in dynamic arc control that improves arc stability and provides a consistent weld quality, even in challenging conditions.

Another key characteristic of the XMC 4000 is its user-friendly interface, featuring a large LCD display that provides real-time data on welding parameters. This allows operators to make quick adjustments as needed, enhancing productivity and efficiency on the job site. The intuitive design also makes it easy for users to navigate through various settings without extensive training.

Durability is a priority with the XMC 4000. The unit is built with high-quality materials and designed to withstand harsh working environments. Its rugged construction, combined with a compact and lightweight design, makes it easy to transport, whether to the job site or between service locations.

In terms of power options, the XMC 4000 is adaptable to various input voltages, allowing it to operate seamlessly in both industrial and field-based applications. This level of flexibility means that welders can use it in diverse locations, making it a reliable companion for on-the-go projects.

Overall, the Miller Electric XMC 4000 stands out as a powerful, versatile, and user-friendly welding machine that meets the demands of today’s welding professionals. Its advanced features, durable design, and multiple process capabilities make it an excellent investment for anyone looking to enhance their welding capabilities.
Top Page Image Contents