Miller Electric Big Blue 600 X, Big Blue 500 PT manual Engine Hazards, Compressed Air Hazards

Page 7

1-3. Engine Hazards

BATTERY EXPLOSION can BLIND.

DAlways wear a face shield, rubber gloves, and

protective clothing when working on a battery.

D Stop engine before disconnecting or connect- ing battery cables or servicing battery.

DDo not allow tools to cause sparks when working on a battery.

DDo not use welder to charge batteries or jump start vehicles.

DObserve correct polarity (+ and −) on batteries.

DDisconnect negative (−) cable first and connect it last.

FUEL can cause fire or explosion.

D Stop engine and let it cool off before checking or adding fuel.

DDo not add fuel while smoking or if unit is near any sparks or open flames.

DDo not overfill tank — allow room for fuel to expand.

DDo not spill fuel. If fuel is spilled, clean up before starting engine.

DDispose of rags in a fireproof container.

DAlways keep nozzle in contact with tank when fueling.

MOVING PARTS can cause injury.

D Keep away from fans, belts, and rotors.

D Keep all doors, panels, covers, and guards closed and securely in place.

DStop engine before installing or connecting unit.

DHave only qualified people remove doors, panels, covers, or guards for maintenance and troubleshooting as necessary.

DTo prevent accidental starting during servicing, disconnect negative (−) battery cable from battery.

DKeep hands, hair, loose clothing, and tools away from moving parts.

DReinstall doors, panels, covers, or guards when servicing is finished and before starting engine.

DBefore working on generator, remove spark plugs or injectors to keep engine from kicking back or starting.

DBlock flywheel so that it will not turn while working on generator components.

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

D Allow cooling period before working on equip- ment.

DTo handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.

STEAM AND HOT COOLANT can burn.

DIf possible, check coolant level when engine is cold to avoid scalding.

D Always check coolant level at overflow tank, if present on unit, instead of radiator (unless told otherwise in maintenance section or engine manual).

DIf the engine is warm, checking is needed, and there is no over- flow tank, follow the next two statements.

DWear safety glasses and gloves and put a rag over radiator cap.

DTurn cap slightly and let pressure escape slowly before completely removing cap.

Using a generator indoors CAN KILL YOU IN MINUTES.

D Generator exhaust contains carbon monoxide.

This is a poison you cannot see or smell.

DNEVER use inside a home or garage, EVEN IF doors and windows are open.

DOnly use OUTSIDE and far away from windows, doors, and vents.

BATTERY ACID can BURN SKIN and EYES.

DDo not tip battery.

DReplace damaged battery.

DFlush eyes and skin immediately with water.

ENGINE HEAT can cause fire.

D Do not locate unit on, over, or near combustible surfaces or flammables.

DKeep exhaust and exhaust pipes way from flammables.

EXHAUST SPARKS can cause fire.

D Do not let engine exhaust sparks cause fire.

DUse approved engine exhaust spark arrestor in required areas — see applicable codes.

1-4. Compressed Air Hazards

BREATHING COMPRESSED AIR can cause serious injury or death.

DDo not use compressed air for breathing.

DUse only for cutting, gouging, and tools.

COMPRESSED AIR can cause injury.

DWear approved safety goggles.

DDo not direct air stream toward self or others.

TRAPPED AIR PRESSURE AND WHIPPING HOSES can cause injury.

DRelease air pressure from tools and system be- fore servicing, adding or changing attach- ments, or opening compressor oil drain or oil fill cap.

OM-4429 Page 3

Image 7
Contents Visit our website at OM-44292216 138H 2007−05 ProcessesDescription File Engine DriveFrom Miller to You Table of Contents − Maintenance & Troubleshooting HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion Fumes and Gases can be hazardousBuildup of GAS can injure or kill ARC Rays can burn eyes and skinCompressed Air Hazards Engine HazardsFalling Unit can cause injury Welding Wire can cause injuryHOT Parts can cause burns and injury Fire or Explosion hazardRadiation can cause interference Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationIndique des instructions spécifiques Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UN Choc Électrique peut tuerLE Bruit peut affecter l’ouïe DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Soudage peut provoquer un in cendie ou une explosionDES Organes Mobiles peuvent pro voquer des blessures ’EXPLOSION DE LA Batterie peu’AIR Comprimé peut provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieRisque D’INCENDIE OU D’EXPLO- Sion ’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électriqueDES Organes Mobiles peuvent provoquer des blessures LES Fils DE Soudage peuvent provoquer des blessuresEn ce qui concerne les implants médicaux Proposition californienne 65 AvertissementsPrincipales normes de sécurité Information EMF− 50 h Std − DefinitionsStd CC Models Manufacturer’s Rating LabelsSome symbols are found only on CE products Symbols And DefinitionsWeld, Power, And Engine Specifications − SpecificationsDimensions, Weights, And Operating Angles Volts Volt-Ampere Curves For CC ModelsVolt-Ampere Curves For CC/CV Models Stick ModeMIG Mode TIG ModeDuty Cycle And Overheating Fuel Consumption100% Duty Cycle At 400 Amperes 20 kVA/kW Three-Phase AC Output No Weld Load AC Generator Power CurveOptional Three-Phase Generator Curves 12 kVA/kW Single-Phase AC Output No Weld LoadGrounding1 − InstallationInstalling Welding Generator Location/Airflow ClearanceUsing Lifting Eye Mounting Welding Generator Stop engine and let cool Installing Exhaust PipeConnecting The Battery Activating The Dry Charge Battery If ApplicableOil Coolant Recovery TankEngine Prestart Checks FuelStop engine Connecting To Weld Output TerminalsStick and TIG Welding MIG and Fcaw Welding350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Connecting to WeldSelecting Weld Cable Sizes 150 ft 200 ft 250 ftSocket Connecting To Remote 14 Receptacle RC14 On CC/CV ModelsOM-4429 Front Panel Controls For CC Models See Section − Operating Welding Generator − CC ModelsWeld Controls Engine Starting ControlsTo Start Engine Gauges And MetersWeld Control/Arc Condition Information Label Remote Amperage Control On CC Models OptionalExample Combination Remote Amperage Control Stick OM-4429 Front Panel Controls For CC/CV Models See Section − Operating Welding Generator − CC/CV Models14 AC/DC Voltmeter Optional Voltage/Amperage Adjust Switch And Remote 14 ReceptacleProcess/Contactor Switch Settings Process/Contactor Switch On CC/CV ModelsExample Combination Remote Amperage Control TIG Remote Voltage/Amperage Control On CC/CV Models OptionalIf a Supplementary − Operating Auxiliary EquipmentVolt And 240 Volt Receptacles At least once a month, run enRear Of Panel Three-Phase Power ConnectionClose panel opening if no connections are made to generator 240 V 15 a AC South African Receptacle RC1 Optional Generator Power ReceptaclesSupplementary Protector CB2 Supplementary Protector CB3 Maintenance Label − Maintenance & TroubleshootingRoutine Maintenance To clean air filter Servicing Air CleanerChecking Generator Brushes Inspecting And Cleaning Optional Spark Arrestor MufflerTo change oil and filter Servicing Fuel And Lubrication SystemsTo replace primary fuel filter Overload Protection Welding − CC Models TroubleshootingWelding − CC/CV Models Optional Three-Phase Generator Power CC/CV Models Only Standard Generator PowerEngine Engine cranks but does not start Check fuel level Check engine wiring harness plug connectionsGine Control switch S1 Factory Authorized Service AgentStart Your Professional Welding Career Now Circuit Diagram For CC Welding Generator − Electrical Diagrams223 525-B Circuit Diagram For CC/CV Welding Generator 223 524-B Wetstacking − RUN-IN ProcedureWelding Generator Keep exhaust and pipe away Run-In Procedure Using Load BankFrom flammables Manual Run-In Procedure Using Resistance GridSpecifications section in this Just generator A/V control soElectrically Bond Generator − Generator Power GuidelinesSelecting Equipment Grounding Generator To Truck Or Trailer FrameAmperes x Volts = Watts Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Use ground device as stated in electrical codesFarm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Industrial Motors Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentKVA/HP x HP x 1000 / Volts = Starting Amperage Power Required To Start MotorHow Much Power Can Generator Supply? Single-Phase Induction Motor Starting RequirementsTypical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible 114 −7 115 CV − Parts List123 116 CV 112 2831 124 88 −6 6059 58 Dia Part Description Quantity Dia Part Description Quantity Mkgs 111 Figures 13-2123 212 Control Box Assembly − CC Models Engine Controller Control Box Assembly − CC Models -1ItemControl Box Assembly − CC/CV Models 134 3634 Panel, Front w/Components − CC Models208278 Panel, Front w/Components − CC/CV Models -1Item Panel, Front w/Components − CC/CV ModelsCB1 201 Supplementary PROTECTOR, man reset 2P 20 A, 250VAC 32 31 30 Hardware is common053 BEARING, Ball Rdl Sgl Row 1.370 X 2.830 X Main Rectifier Assembly Wiring Harnesses 215207 Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact