Miller Electric OM-129, 500DX R manual Approximate Power Requirements For Contractor Equipment

Page 52

10-7. Approximate Power Requirements For Contractor Equipment

Contractor	Rating	Starting Watts	Running Watts

Hand Drill	1/4 in	350	350
	3/8 in	400	400
	1/2 in	600	600
Circular Saw	6-1/2 in	500	500
	7-1/4 in	900	900
	8-1/4 in	1400	1400
Table Saw	9 in	4500	1500
	10 in	6300	1800
Band Saw	14 in	2500	1100
Bench Grinder	6 in	1720	720
	8 in	3900	1400
	10 in	5200	1600
Air Compressor	1/2 HP	3000	1000
	1 HP	6000	1500
	1-1/2 HP	8200	2200
	2 HP	10500	2800
Electric Chain Saw	1-1/2 HP, 12 in	1100	1100
	2 HP, 14 in	1100	1100
Electric Trimmer	Standard 9 in	350	350
	Heavy Duty 12 in	500	500
Electric Cultivator	1/3 HP	2100	700
Elec. Hedge Trimmer	18 in	400	400
Flood Lights	HID	125	100
	Metal Halide	313	250
	Mercury	1000
	Sodium	1400
	Vapor	1250	1000
Submersible Pump	400 gph	600	200
Centrifugal Pump	900 gph	900	500
Floor Polisher	3/4 HP, 16 in	4500	1400
	1 HP, 20 in	6100	1600
High Pressure Washer	1/2 HP	3150	950
	3/4 HP	4500	1400
	1 HP	6100	1600
55 gal Drum Mixer	1/4 HP	1900	700
Wet & Dry Vac	1.7 HP	900	900
	2-1/2 HP	1300	1300

OM-129 647 Page 48

Image 52

Contents Processes OM-129 647WDescription From Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill ARC Rays can burn eyes and skinEngine Hazards Battery Explosion can Blind Moving Parts can cause injuryEngine Exhaust Gases can kill Engine Heat can cause firePrincipal Safety Standards EMF InformationRadiation can cause interference ARC Welding can cause interferenceSignification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent provoquer des blessures ’EXPLOSION DE LA Batterie peutLA Chaleur DU Moteur peut pro- voquer un incendie LA Chute DE L’APPAREIL peut blesserPrincipales normes de sécurité Information sur les champs électromagnétiquesLE Soudage À L’ARC risque de provoquer des interférences Consignes relatives aux stimulateurs cardiaques− Specifications Symbols And DefinitionsWeld, Power, And Engine Specifications − DefinitionsDimensions, Weights, And Operating Angles Curve shows typical fuel use under weld or power loadsFuel Consumption 1898 lb 861 kg Engine EndAC Auxiliary Power Warranty Minutes Welding Minutes RestingDuty Cycle And Overheating 60% Duty Cycle At 500 Amperes Duty Cycle is PercentageVolt-Ampere Curves CC/DC Standard CV/DC Models With CV OptionOptional AC Power Plant Curves − Installation Installing Welding GeneratorDo Not Lift Unit From End Airflow Clearance LocationActivating The Dry Charge Battery When electrolyte is low, addCharger Maintain proper levelConnecting The Battery Engine Prestart ChecksConnect Negative − Cable Last Tools Needed 1/2Connecting To Weld Output Terminals Selecting Weld Cable SizesAfter installing cylinder, wait at Installing Ether Cylinder Optional Ether Starting AidRemote A/V Control Receptacle RC3 Remote 14 Receptacle RC3 Information Optional Terminal Strip 2T Connections OptionalSocket Stop engine− Operating the Welding Generator Standard Controls See SectionDo not switch under load Description Of Standard Controls See SectionIf light goes off, stop engine and check oil level If light goes on, stop engine and check engine beltControls For Models With CV Option See Section This unit has a max OCV control circuit Auxiliary power is not affected by weld output − Operating Auxiliary EquipmentVolt And 240 Volt Duplex Receptacles 120 V 15 a AC Receptacle RC2 240 V 15 a AC Receptacle RC1Optional Auxiliary Power Receptacles Gfci Receptacle OptionAustralian And South African Receptacle Options British Receptacle OptionConnecting Optional Auxiliary Power Plant Set Engine Control switch to Run when using auxiliary power1011 Load Terminals− Maintenance & Troubleshooting Maintenance Label Deutz F3L912 Diesel EngineTo clean air filter Servicing Air CleanerHose Servicing Fuel And Lubrication Systems Servicing Optional Ether Starting Aid Adjusting Engine Speed1850 To adjust belt tension Checking And Replacing Alternator Belt13 mm Max Tools Needed 11/16 Stop engine To check belt tensionResetting Fan Belt Safety Shutdown Inspecting And Cleaning Optional Spark Arrestor Muffler Stop engine and let cool. Reinstall cleanout plugOverload Protection For Models With CV Option Stop engine and let coolTroubleshooting WeldingAuxiliary Power EngineTrouble Remedy OM-129 647 − Electrical Diagrams Circuit Diagram For Welding Generator Standard ModelsCircuit Diagram For Welding Generator Models With CV Option 184 954-C − RUN-IN Procedure WetstackingRun-In Procedure Using Load Bank Load BankRun-In Procedure Using Resistance Grid Do not touch hot exhaustBank/grid From flammablesSelecting Equipment − Auxiliary Power GuidelinesGrounding Generator To Truck Or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require?Earth ground if supplying Use ground device as stated in electrical codesApproximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsPower Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting Amperage VoltsGenerator is to supply standby power during Emergencies or power outagesWelding Generator Auxiliary Power output circuit Customer-supplied equipment is required ifSelecting Extension Cord Use Shortest Cord Possible − Parts List 101 10066 65 102 Dia Part Description Quantity Mkgs Optional Panel, Front w/Components CC Model Illustrated Panel, Front w/Components -1 Item Generator 6 5Generator -1 Item Hardware is common Not available unless listed 171Includes Control Box CC/CV -1 Item 86 Optional Panel, Mtg Components CC/CV Model Panel, Mtg Components CC Model Page Your distributor also gives ServiceSupport To locate distributor nearest you call 1-800-4-A-Miller Miller Electric Mfg. CoFor assistance in filing or settling claims