Miller Electric Bobcat 225 manual Engine Hazards, Compressed Air Hazards

Page 7

1-3. Engine Hazards

BATTERY EXPLOSION can BLIND.

DAlways wear a face shield, rubber gloves, and

protective clothing when working on a battery.

D Stop engine before disconnecting or connect- ing battery cables or servicing battery.

DDo not allow tools to cause sparks when working on a battery.

DDo not use welder to charge batteries or jump start vehicles.

DObserve correct polarity (+ and −) on batteries.

DDisconnect negative (−) cable first and connect it last.

FUEL can cause fire or explosion.

D Stop engine and let it cool off before checking or adding fuel.

DDo not add fuel while smoking or if unit is near any sparks or open flames.

DDo not overfill tank — allow room for fuel to expand.

DDo not spill fuel. If fuel is spilled, clean up before starting engine.

DDispose of rags in a fireproof container.

DAlways keep nozzle in contact with tank when fueling.

MOVING PARTS can cause injury.

D Keep away from fans, belts, and rotors.

D Keep all doors, panels, covers, and guards closed and securely in place.

DStop engine before installing or connecting unit.

DHave only qualified people remove doors, panels, covers, or guards for maintenance and troubleshooting as necessary.

DTo prevent accidental starting during servicing, disconnect negative (−) battery cable from battery.

DKeep hands, hair, loose clothing, and tools away from moving parts.

DReinstall doors, panels, covers, or guards when servicing is finished and before starting engine.

DBefore working on generator, remove spark plugs or injectors to keep engine from kicking back or starting.

DBlock flywheel so that it will not turn while working on generator components.

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

D Allow cooling period before working on equip- ment.

DTo handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.

STEAM AND HOT COOLANT can burn.

DIf possible, check coolant level when engine is cold to avoid scalding.

D Always check coolant level at overflow tank, if present on unit, instead of radiator (unless told otherwise in maintenance section or engine manual).

DIf the engine is warm, checking is needed, and there is no over- flow tank, follow the next two statements.

DWear safety glasses and gloves and put a rag over radiator cap.

DTurn cap slightly and let pressure escape slowly before completely removing cap.

Using a generator indoors CAN KILL YOU IN MINUTES.

D Generator exhaust contains carbon monoxide.

This is a poison you cannot see or smell.

DNEVER use inside a home or garage, EVEN IF doors and windows are open.

DOnly use OUTSIDE and far away from windows, doors, and vents.

BATTERY ACID can BURN SKIN and EYES.

DDo not tip battery.

DReplace damaged battery.

DFlush eyes and skin immediately with water.

ENGINE HEAT can cause fire.

D Do not locate unit on, over, or near combustible surfaces or flammables.

DKeep exhaust and exhaust pipes way from flammables.

EXHAUST SPARKS can cause fire.

D Do not let engine exhaust sparks cause fire.

DUse approved engine exhaust spark arrestor in required areas — see applicable codes.

1-4. Compressed Air Hazards

BREATHING COMPRESSED AIR can cause serious injury or death.

DDo not use compressed air for breathing.

DUse only for cutting, gouging, and tools.

COMPRESSED AIR can cause injury.

DWear approved safety goggles.

DDo not direct air stream toward self or others.

TRAPPED AIR PRESSURE AND WHIPPING HOSES can cause injury.

DRelease air pressure from tools and system be- fore servicing, adding or changing attach- ments, or opening compressor oil drain or oil fill cap.

OM-4434 Page 3

Image 7
Contents File Engine Drive OM-4434From Miller to You Table of Contents 11-1 10-110-2 10-3HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion Fumes and Gases can be hazardousBuildup of GAS can injure or kill ARC Rays can burn eyes and skinCompressed Air Hazards Engine HazardsFalling Unit can cause injury Welding Wire can cause injuryHOT Parts can cause burns and injury Fire or Explosion hazardRadiation can cause interference Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationIndique des instructions spécifiques Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UN Choc Électrique peut tuerLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion ’EXPLOSION DE LA Batterie peu LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent pro voquer des blessures ’AIR Comprimé peut provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieRisque D’INCENDIE OU D’EXPLO- Sion ’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électriqueDES Organes Mobiles peuvent provoquer des blessures LES Fils DE Soudage peuvent provoquer des blessuresPrincipales normes de sécurité Proposition californienne 65 AvertissementsInformation EMF − Definitions − SpecificationsSymbol Definitions Weld, Power, and Engine SpecificationsDimensions Dimensions, Weights, and Operating AnglesDimensions For Units With Optional Running Gear Robin-PoweredUnit 560 lb 254 kgFuel Consumption Kohler-Powered Units Fuel Consumption Robin-Powered UnitsFor CC/DC Mode For CV/DC Mode For CC/AC ModeVolt-Ampere Curves Duty Cycle Generator Power CurveDo not use flexible mounts Grounding − InstallationInstalling Welding Generator MountingOil Check Engine Prestart Checks Robin-Powered UnitsOil Engine Prestart Checks Kohler-Powered Units Replacing The Battery Installing Exhaust PipeConnecting Or Replacing the Battery Connecting The Battery Connect negative − cable lastWork Weld Output Terminal Connecting to Weld Output TerminalsTools Needed Correct Installation Stop engine150 ft 200 ft 250 ft Selecting Weld Cable Sizes350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m OM-4434 − Operating the Welding Generator Engine Control SwitchPlace switch in Run position to operate most MIG equipment Coarse Range SwitchFrequently Loaded Cold Weather Engine OperationInfrequently LoadedElectrode Typical Stick Welding Connections And Control SettingsSolid Wire Applications Typical MIG Welding Connections And SettingsBe sure to use the correct size weld cables see Section Fine Control, Weld Process switch Settings Self-Shielded Flux Core Wire ApplicationsWork Typical Settings ForSet wire feed speed between 240-270 ipm OM-4434 MaterialStandard Receptacles − Operating Auxiliary EquipmentBreaker trips Optional Generator Power ReceptaclesReceptacle Simultaneous Weld And PowerWiring Optional 240 Volt Plug Current Available in Amperes 240Maintenance Label Robin-Powered Units − Maintenance ROBIN-POWERED Units200 Routine Maintenance Robin-Powered UnitsStop engine before maintaining 100Servicing Optional Spark Arrestor Robin-Powered Units Servicing Air Cleaner Robin-Powered UnitsStop engine and let cool Oil Fill Close valve and valve capBefore adding oil Running engineWeld/Power Speed Adjustment Adjusting Engine Speed Robin-Powered UnitsIdle Speed Adjustment Turn idle speed screw for fine adjustmentsStop engine. Disconnect negative − battery cable Overload Protection Robin-Powered UnitsMaintenance Label Kohler-Powered Units − Maintenance − KOHLER-POWERED UnitsHours Nl Weld Cables ~ Slip Rings Nl Brushes OM-4434 Routine Maintenance Kohler-Powered UnitsServicing Air Cleaner Kohler−Powered Units 2 ID x 7 in Hose Oil Filter Stop engine and let cool Oil Drain ValveFull Before adding oil Running engine Turn idle speed screw for fine ad- justments Adjusting Engine Speed Kohler-Powered UnitsServicing Optional Spark Arrestor Kohler-Powered Units Overload Protection Kohler-Powered UnitsIf a fuse opens, it usually indi Trouble Remedy − TroubleshootingWelding Troubleshooting Generator Power TroubleshootingEngine Troubleshooting Recommended Spare Parts − Parts ListControl switch S2, and throttle solenoid TS1 Recommended Spare PartsCircuit Diagram For Welding Generator − Electrical Diagrams228 461-A Selecting Equipment − Generator Power GuidelinesGrounding Generator To Truck Or Trailer Frame How Much Power Does Equipment Require? Grounding When Supplying Building SystemsFarm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Industrial Motors Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentKVA/HP x HP x 1000 / Volts = Starting Amperage Power Required To Start MotorHow Much Power Can Generator Supply? Single-Phase Induction Motor Starting RequirementsTypical Connections To Supply Standby Power Cord Lengths for 240 Volt Loads Selecting Extension Cord Use Shortest Cord PossibleCord Lengths for 120 Volt Loads Current Load Watts Amperes− Stick Welding Smaw Guidelines Stick Welding ProcedureStriking an Arc − Scratch Start Technique Electrode and Amperage Selection ChartStriking an Arc − Tapping Technique 10-30 9090 End View of Work Angle Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Positioning Electrode HolderElectrode Movement During Welding Conditions That Affect Weld Bead Shape16 in 30 1.6 mm Tack Welds Butt JointsLap Joint Tee JointPossible Causes Corrective Actions Troubleshooting − PorosityTroubleshooting − Excessive Spatter Weld TestTroubleshooting − Lack Of Penetration Troubleshooting − Incomplete FusionTroubleshooting − Excessive Penetration Troubleshooting − Waviness Of Bead Troubleshooting − Burn-ThroughTroubleshooting − Distortion Holding And Positioning Welding Gun − MIG Welding Gmaw GuidelinesShort Normal Long Push Perpendicular DragSlow Normal Fast Gun Movement During Welding 15-8 Troubleshooting − Porosity 15-7 Troubleshooting − Excessive Spatter15-9 Troubleshooting − Excessive Penetration Fusion between weld metal Lack Of Penetration − shallowImproper joint preparation Base metal to move Unsteady hand Support hand on solid surface or use two handsApplication Common MIG Shielding GasesFillet Page Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact