Miller Electric Bobcat 225 manual Adjusting Engine Speed Kohler-Powered Units

Page 47

. A complete Parts List is available at www.MillerWelds.com

9-5. Adjusting Engine Speed (Kohler-Powered Units)

2200 − 2300 rpm

(36.6 − 38.3 Hz)

3675 − 3750 rpm

(61.3 − 62.5 Hz)

1

5

4	2

After tuning engine, check engine speeds with a tachometer (see table). If necessary, adjust speeds as follows:

Start engine and run until warm. Turn Fine Control to 10.

Remove rear panel and air cleaner to access idle speed adjustments. Remove top cover to access weld/ power speed adjustments.

Idle Speed Adjustment

Move Engine Control switch to Run/Idle position.

1Throttle Solenoid

2Mounting Screws

3Idle Speed Screw

Loosen mounting screws. Adjust solenoid position so engine runs at idle speed. If necessary, back out idle speed screw so solenoid can be moved to correct position. Tight- en mounting screws. Be sure sole- noid linkage works smoothly.

Turn idle speed screw for fine ad- justments.

Weld/Power Speed Adjustment

Move Engine Control switch to Run position.

4 Weld/Power Speed

Adjustment Nut

3	5 Lock Nut

Top View

Loosen lock nut. Turn adjustment nut until engine runs at weld/power speed. Tighten lock nut.

! Stop engine.

Reinstall air cleaner, rear panel, and top cover.

Tools Needed:

1/4, 3/8 in

803 849 / 801 209-A

OM-4434 Page 43

Image 47

Contents File Engine Drive OM-4434From Miller to You Table of Contents 11-1 10-110-2 10-3HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion Fumes and Gases can be hazardousBuildup of GAS can injure or kill ARC Rays can burn eyes and skinCompressed Air Hazards Engine HazardsFalling Unit can cause injury Welding Wire can cause injuryHOT Parts can cause burns and injury Fire or Explosion hazardRadiation can cause interference Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationIndique des instructions spécifiques Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UN Choc Électrique peut tuerLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux DES Organes Mobiles peuvent pro voquer des blessures LE Bruit peut affecter l’ouïe’EXPLOSION DE LA Batterie peu Risque D’INCENDIE OU D’EXPLO- Sion LA Chaleur DU Moteur peut pro- voquer un incendie’AIR Comprimé peut provoquer des blessures ’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électriqueDES Organes Mobiles peuvent provoquer des blessures LES Fils DE Soudage peuvent provoquer des blessuresInformation EMF Proposition californienne 65 AvertissementsPrincipales normes de sécurité − Definitions − SpecificationsSymbol Definitions Weld, Power, and Engine SpecificationsDimensions Dimensions, Weights, and Operating AnglesDimensions For Units With Optional Running Gear Robin-PoweredUnit 560 lb 254 kgFuel Consumption Kohler-Powered Units Fuel Consumption Robin-Powered UnitsVolt-Ampere Curves For CC/AC ModeFor CC/DC Mode For CV/DC Mode Duty Cycle Generator Power CurveDo not use flexible mounts Grounding − InstallationInstalling Welding Generator MountingOil Engine Prestart Checks Robin-Powered UnitsOil Check Engine Prestart Checks Kohler-Powered Units Replacing The Battery Installing Exhaust PipeConnecting Or Replacing the Battery Connecting The Battery Connect negative − cable lastWork Weld Output Terminal Connecting to Weld Output TerminalsTools Needed Correct Installation Stop engine350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Selecting Weld Cable Sizes150 ft 200 ft 250 ft OM-4434 − Operating the Welding Generator Engine Control SwitchPlace switch in Run position to operate most MIG equipment Coarse Range SwitchFrequently Loaded Cold Weather Engine OperationInfrequently LoadedElectrode Typical Stick Welding Connections And Control SettingsBe sure to use the correct size weld cables see Section Typical MIG Welding Connections And SettingsSolid Wire Applications Fine Control, Weld Process switch Settings Self-Shielded Flux Core Wire ApplicationsWork Typical Settings ForSet wire feed speed between 240-270 ipm OM-4434 MaterialStandard Receptacles − Operating Auxiliary EquipmentBreaker trips Optional Generator Power ReceptaclesReceptacle Simultaneous Weld And PowerWiring Optional 240 Volt Plug Current Available in Amperes 240Maintenance Label Robin-Powered Units − Maintenance ROBIN-POWERED Units200 Routine Maintenance Robin-Powered UnitsStop engine before maintaining 100Stop engine and let cool Servicing Air Cleaner Robin-Powered UnitsServicing Optional Spark Arrestor Robin-Powered Units Oil Fill Close valve and valve capBefore adding oil Running engineWeld/Power Speed Adjustment Adjusting Engine Speed Robin-Powered UnitsIdle Speed Adjustment Turn idle speed screw for fine adjustmentsStop engine. Disconnect negative − battery cable Overload Protection Robin-Powered UnitsMaintenance Label Kohler-Powered Units − Maintenance − KOHLER-POWERED UnitsHours Nl Weld Cables ~ Slip Rings Nl Brushes OM-4434 Routine Maintenance Kohler-Powered UnitsServicing Air Cleaner Kohler−Powered Units Full Before adding oil Running engine Stop engine and let cool Oil Drain Valve2 ID x 7 in Hose Oil Filter Turn idle speed screw for fine ad- justments Adjusting Engine Speed Kohler-Powered UnitsIf a fuse opens, it usually indi Overload Protection Kohler-Powered UnitsServicing Optional Spark Arrestor Kohler-Powered Units Trouble Remedy − TroubleshootingWelding Troubleshooting Generator Power TroubleshootingEngine Troubleshooting Recommended Spare Parts − Parts ListControl switch S2, and throttle solenoid TS1 Recommended Spare PartsCircuit Diagram For Welding Generator − Electrical Diagrams228 461-A Grounding Generator To Truck Or Trailer Frame − Generator Power GuidelinesSelecting Equipment How Much Power Does Equipment Require? Grounding When Supplying Building SystemsFarm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Industrial Motors Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentKVA/HP x HP x 1000 / Volts = Starting Amperage Power Required To Start MotorHow Much Power Can Generator Supply? Single-Phase Induction Motor Starting RequirementsTypical Connections To Supply Standby Power Cord Lengths for 240 Volt Loads Selecting Extension Cord Use Shortest Cord PossibleCord Lengths for 120 Volt Loads Current Load Watts Amperes− Stick Welding Smaw Guidelines Stick Welding ProcedureStriking an Arc − Tapping Technique Electrode and Amperage Selection ChartStriking an Arc − Scratch Start Technique 10-30 9090 End View of Work Angle Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Positioning Electrode HolderElectrode Movement During Welding Conditions That Affect Weld Bead Shape16 in 30 1.6 mm Tack Welds Butt JointsLap Joint Tee JointPossible Causes Corrective Actions Troubleshooting − PorosityTroubleshooting − Excessive Spatter Weld TestTroubleshooting − Excessive Penetration Troubleshooting − Incomplete FusionTroubleshooting − Lack Of Penetration Troubleshooting − Distortion Troubleshooting − Burn-ThroughTroubleshooting − Waviness Of Bead Holding And Positioning Welding Gun − MIG Welding Gmaw GuidelinesSlow Normal Fast Push Perpendicular DragShort Normal Long Gun Movement During Welding 15-9 Troubleshooting − Excessive Penetration 15-7 Troubleshooting − Excessive Spatter15-8 Troubleshooting − Porosity Improper joint preparation Lack Of Penetration − shallowFusion between weld metal Base metal to move Unsteady hand Support hand on solid surface or use two handsFillet Common MIG Shielding GasesApplication Page Support ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact