Bosch Power Tools 11265EVS, 11264EVS manual Assembly, Operating Instructions

Page 7

BM 1619929843 05-08 5/21/08 3:39 PM Page 7

Assembly

INSTALLING ACCESSORIES

Clean the insert shank end of the accessory to remove any debris, then lightly grease with a light oil or lubricant.

(Model 11264EVS

Insert accessory into the tool holder, while twisting and pushing inward until it locks automatically into place (Fig. 2).

(Model 11265EVS

To install hex round chisels, align flat on chisel with alignment mark on tool holder, then push chisel into tool holder until it locks automatically into place. Pull outward on the accessory to be certain it is locked into the tool holder (Fig. 3).

REMOVING ACCESSORIES

!WARNING Accessories may be hot after use. Avoid contact with skin

and use proper protective gloves or cloth to remove.

(Model 11264EVS

To remove an accessory, pull locking sleeve backward until it locks into place, then pull bit forward. All accessories should be wiped clean after removing (Fig. 2).

(Model 11265EVS

To remove an accessory, pull and hold locking sleeve backward and pull bit forward. All accessories should be wiped clean after removing (Fig. 3).

NOTE: The high efficiency available from the rotary hammers can only be obtained if sharp and undamaged accessories are used. The "cost" to maintain sharp and undamaged

accessories is more than offset by the "time saved" in operating the tool with sharp accessories.

FIG. 2

LOCKING SLEEVE

HEX ROUND CHISEL

FLAT

 

ALIGNMENT

 

MARK

FIG. 3

LOCKING

SLEEVE

AUXILIARY HANDLE

The tool must be supported with the auxiliary handle, which can be swiveled 360˚. To reposition and/or swivel the handle, loosen the hand grip, move the handle to the desired position along the barrel and securely retighten the hand grip.

VIBRATION DAMPER HANDLE /

HAMMER MECHANISM

The integrated vibration damper in the main handle and hammer mechanism reduces vibrations (Fig. 1).

Operating Instructions

POWER INDICATOR LIGHT

When you plug your tool into the power source, the power indicator light will go “ON” indicating the tool is receiving power.

SLIP CLUTCH

The tool has a internal pre-set slip clutch. The output spindle will stop rotating if the accessory binds and overloads the tool.

-7-

Image 7
Contents Read Before Using Personal safety General Power Tool Safety WarningsWork area safety Electrical safetyPower tool use and care Combination Hammer Safety RulesService Accessories may be hot after prolonged use Symbol Name Designation/Explanation SymbolsCombination Hammer Functional Description and SpecificationsOperating Instructions AssemblyVariable Speed Dial Trigger Release SwitchTurbo Feature Trigger Controlled Variable SpeedCleaning MaintenanceTool Tips Tool’s AccessoriesSécurité électrique Sécurité du lieu de travailSécurité personnelle Entretien Utilisation et entretien des outils ÉlectroportatifsLe plomb provenant des peintures à base de plomb Symbole Nom Désignation/Explication SymbolesModèle 11265EVS seulement Description fonctionnelle et spécificationsPerceuse à percussion de combinaison PORTE-OUTIL CanneléConsignes de fonctionnement AssemblageLevier Sélecteur Molette DE Variation DE VitesseFonction « Turbo » Circuit D’ASSERVISSEMENT « Constant Response »Conseils Pratiques Conseils PratiquesEntretien AccessoiresNettoyage Seguridad eléctrica Seguridad del área de trabajoSeguridad personal Servicio de ajustes y reparaciones MecánicasBM 1619929843 05-08 5/21/08 339 PM Símbolo Nombre Designación/explicación SímbolosTaladro de percusión de combinación Descripción funcional y especificacionesInstrucciones de funcionamiento EnsamblajePalanca Selectora Dial DE Velocidad VariableFuncion Turbo Circuitería DE Respuesta ConstanteLimpieza Consejos para la herramientaMantenimiento ServicioCapacidad AccesoriosBM 1619929843 05-08 5/21/08 339 PM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools