Hitachi H 45MR instruction manual Service and repairs, Service parts list

Page 15

English

(2) How to replace grease

CAUTION:

◯Before replacing the grease, turn the power off and pull out the plug from the receptacle.

1Disassenble the crank cover and thorougly wipe off the old grease inside.

2Supply 1.3 oz (40 g) (the standard volume to cover the connecting rod) of Hitachi Electric Hammer Grease A in the crank

case.

3After replacing the grease, reassemples the crank cover securely. At this time, do not damage or lose the oil seal.

Crank Cover

Fig. 11

NOTE:

◯The Hitachi Electric Hammer Grease A is of the low viscosity type. When the grease is consumed, purchase from the authorized Hitachi Service Center.

◯Do not excessively supply the designated amount of grease. Otherwise, the tool should not operate accurately.

6.Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.

7.Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

15

Image 15

Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Never use a tool which is defective or operating abnormallyDouble Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolSpecifications Functional DescriptionName of Parts Removing Tool AssemblyInstalling Tools Deciding Working Position of ToolMove the side handle Operation ApplicationsPrior to Operation HOW to USE the Demolition Hammer Maintenance and Inspection Service parts list Service and repairsAccessories Standard AccessoriesSold separately Tamping Rammer Shank Code No Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéAvertissement Lire et coxmprendre toutes les instructions SecuriteRegles Generale DE Securite Conserver CES InstructionsFrançais Ne jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesGarder propres les évents d’air du moteur Utiliser l’outil motorisé à la tension nominaleNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleRetrait de l’outil Installation des outilsAssemblage Recherche de la position de travail de l’outilDéplacer la poignée latérale Avant L’UTILISATION FonctionnementComment Utiliser LE Marteau Piqueur Inspection des vis Remplacement de graisseEntretien ET Inspection Inspection de l’outilListe des pièces de rechange Service apres-vente et reparationsAccessoires Standard AccessoiresFrançais Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadAdvertencia Lea y entienda todas las instrucciones SeguridadNormas Generales DE Seguridad Guarde Estas InstruccionesEspañol Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadNo toque nunca las piezas móviles Utilice la herramienta correctaNo limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricasAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones Extracción de la herramienta MontajeInstalación de herramientas Decisión de la posición de trabajo de la herramientaMueva el asa lateral Operación AplicacionesAntes DE LA Operación Forma DE Usar EL Martillo Demoledor Inspeccionar los carbones de contacto Fig Mantenimiento E InspecciónInspección d la herramienta Inspección de los tornillosPage Accesorios Accesorios EstándarDe venta por separado Español Page 6201DDCMPS2L Page Page Hitachi Koki Canada Co