DeWalt DWE4559CN instruction manual FIG3, Wheel Mountin9 Accessories Attachments, Attach M Ents

Page 11

Thesidehandleshouldbeusedasthesecondarygripsurfaceforall otherapplications.

FIG3. \

3.Reinstall screws to attach the gear case to the motor housing. Tighten screws to 20 in.-Ibs, torque. Overtightening could cause screws to strip.

Rotating the Rear Handle (Fig. 5)

Thegearcasegripmaybepurchasedat additionalcost.Please call 1-800-4-DEWALT(1-800-433-9258)or visit our website: www.dewalt.com.

Ro*a*in9 the Gear Case (Fig. 4)

For applications in which a tool will be FIG.4 dedicated for uses in edge grinding and finishing work, the gear case may be rotated 90 ° left or right of its original position.

1.Remove the four corner screws

attaching the gear case to motor housing.

2.Without separating the gear case from motor housing, rotate the gear case head to desired position.

NOTE: If the gear case and motor housing become separated by more than 1/8" (3.17 mm), the tool must be serviced and re-assembled by a DEiWALTservice center. Failure to have the tool serviced may cause brush, motor and bearing failure.

10

(D28499 ONLY}

FIG.5

1.

Unlock

the rear handle by

_90o

 

pulling out the Handle Release

1

 

Lever (L).

2.

Rotate

handle into available

6°°

0°, 30 °, 60°, or 90 ° position left OR right of center.

3.Push in the handle release lever.

4.Before turning the tool on, ensure that the handle is locked into a position and the handle release lever has returned to the original position flush with the tool housing.

Wheel Mountin9 Accessories and

Attachments

It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. Refer to pages 11-13 for information on choosing the correct wheel mounting accessories.

ATTACH M ENTS

Attachments designed specifically for this grinder can be purchased through DEWALT dealers and DEWALT Factory Service centers.

9" Type 27 guard

D284939

9" Type 28 guard

D284938

7" Type 27 guard

D284937

5"-6" Type 11 flaring cup guard with flange

D284936

4" Type 11 flaring cup guard with flange

D284934

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Heavy Duty Large Angle Grinders Electrical Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Work Area SafetyFor your Stay alertUse Common Do notAbrasivej Cuing-OffOperations Safety iNSTRUCTiONS forService ALL OperationsKickback and Related Warnings Position the cord clear of the spinning accessory. /f youRegularly clean the power tools air vents. The motors Contactwithwheel,andsparksthatcouldigniteclothing Additional Safety Warnings Specific forSafety Warnings Specific for Polishing Operations Safety Warnings Specific for SandingBrushing Operations Safety Warnings Specific for WireAdditional Safety Rules for Grinders Future USE Save These iNSTRUCTiONS forToughcord TM System FamiliarizationDust Ejection System DWE4597, DWE4597N, DWE4599N Switch Protection TMAttacMng Side Handle FigAttach M Ents Wheel Mountin9 Accessories AttachmentsFIG3. \ Mounting and Removing Guard Mounting GuardSanding Flap Discs Grinding Wheels Sanding Discs Type28hubbedwheelWheels Wire WheelsFlaring Cup Stones When Switch FigOperation ReduceMounting NON-HUBBED Wheels Trigger Operation with LOCK-ONFEATURESpindle Lock Button FIG Mounting and Removing Hubbed WheelsMounting Sanding Backing Pads FIG ThewheeltostoprotatingbeforelayingthetooldownSandingdiscwhiledepressingthespindlelockbutton Precautions To Take When Sanding PaintUsing Sanding Backing Pads FIG Environ M Ental SafetyDustoutsidetheworkarea Mounting and Using Wire Brushes and Wire WheelsCleaning and Disposal Mounting Wire CUP Brushes and Wire WheelsMounting Flaring CUP Wheel Guard FIG Mounting and Using Cutting Type 1 WheelsMounting and Using Flaring Cup Using a Flaring CUP Wheel FIGMounting Cutting Wheels FIG Using Cutting WheelsRegister Online MaintenanceThewheeltobendandmaycausewheelbreakage RepairsDAY Money Back Guarantee Three Year Limited WarrantyYear Free Service Pour les outils lectriques Dfinitions Iignes directrices en rnatire de scuritAver*issernents de scurit gnraux ET Toutes LES Directives Pour UN Usage UlterieurUtilisation ET Entretien Dunoutil ¢LECTRIOUE Nepas exposerlosoutils61ectriques b la pluie ou bSECURITi Personnelle #PARATION BNepas utiliserun outil61ectrique dent IinterrupteurToutes L£S Operations Page Aux operations de rneulage et de coupe Par abrasion NNepasfairefonctionnerIoutil61ectrique b proximit6 deRebonds eft avertissernents all, rents Avertissements de scurit spcifiquesSupplrnentaires spcifiques aux Avertissernents de scuritAux rneuleuses Rgles additionnelles de scurit propresNon recommande Pendant Conserver CES Consignes PourULT E-RIEURE RouteCarter Automatique Description j 9POIGN#E Arriere ANTI-VIBRATIONS FIG Systeme DI#VACUATION DES Poussieres=CLUTCH Mc DWE4597, DWE4597N, DWE4599N Installation De la poigne LatraleLaterale H peut tre installee sur Iun ou EmbrayageSEU LEM ENT Installation de rneules et daccessoiresPositionnement de la poigne artiste Dewalt Disques de pon age , feuillets¢¢I=SSOI R I=S Meules D284937po D284939po Type27hubbedwheelD284938po Meuleavecmoyeun28Meules abrasives Brosses mdtalliquesMeules boisseaux Assemblage ET Retrait DU Capot Protecteur Assemblage du capot protecteurUtilisation DE Linterrupteur a Gachette FonctionnementInterrupteur Fig Meulage DE Surface Avec DES Meules FIG Installation ET Reftrait DES Meules Avec MoyeuInstallation DES Meules Sans Moyeu Meulagede Chant Avec DES Meules FIG Abrasifjusquce quele disqueet LetamponSToutenenfonantleboutondeverrouillage La brochetouten tournantle disqueNettoyage ET Mise AU Rebut SECURITiPERSONNELLERespect DE Lenvironnement Brosses Mtalliques a Touret FIG Utilisation DE Brosses Forme Coupelle ET DEMontage DU Capot Protecteur FERM¢ DE Type INSTALLATiON DES MeulesMontage et utilisation de meules Boisseaux Coniques FIGUtilisation DE Disques DE Coupe Pourretirerlecapotprotecteur,degagerMontage DE Disques DE Coupe FIG Rparations AccessoiresNeoyage Garantie DE Remboursement DE 90 Jours Remplacement Gratuit DES EtiquettesGarantie lirnite de trois ans Contrat Dentretien Gratuit DUN ANSeguridad EN EL Area DE Trabajo Definiciones Normas de seguridadConserve Todas LAS Advebtencias IADVERTENCIA! Lea todas las advertencias de seguridadUSO Y Mantenimiento DE LA Herramienta Electrica Seguridad PersonalMantenimiento Instrucciones DE Segubidad Paba Todas LAS OpebacionesAdvertencias de seguridad comunes para Page Bebote g advertencias relacionadas Para operaciones de pulido Advertencias de seguridad especificasNorrnas de seguridad adicionales para esrneriladoras Para operaciones de cepillado con cepillo de alarnbreLargo total RPM GUARD£ Estas Instrucciones Para Futuras ConsultasSistema DE Extraccion DE Polvo Switch Protection TM Proteccion DE Interruptor ElectronicoUSO Debido Mango Trasero Antivibraciones FIG=CLUTCH TM MONTAJ£ Y AjustesFijaci6n MangeD28499 Solamente Rotaci6n de la caja de engranajes FigComo girar mango trasero Fig Accesorios y dispositivos para el montaje de los discosDispositivos Sanding Flap DiscsDiscos de lijar Guardatipo27 D2849377 D2849399 Discodetipo27Guardatipo28 D2849389 Discotipo28Discos de corse Ce illos de alambreCopa de Piedra Accesorio podria Protector de rnontajeMontaje Y Extraccion DEL Protector ATENCI6NEncendido Permanente FUNCIONAMI£NTOInterrupter Fig Esmerilado DE Bordes CON Discos DE Esmerilar FIG Instalacidn DE Discos CON Centro DeprimidoEsmerilado DE Superficie CON Discos DE Esmerilar Montaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos DE Lijar FIGSeguridad Personal Precauciones que debe tenet en cuentaAl lijar pintura USO DE Almohadillas DE Respaldo Para Lijar FIGAlambre. Pueden Discos AlambreBeberofumarNosedebendejarartculosparacomer,beber ReducirInstalaci6n y utilizaci6n de piedras Permitaquelaherramientaalcancelavelocidadm6,ximaantesdeAplicarlalasuperficiedetrabajo SobreunasuperficieTipo 1 AntesdeusarelesmeriladorSeextiendaApretarfirmementelostornillosdelacamisadelaguarda Montaje y uso de discos de corteMontaje DE LOS Discos DE Corte FIG Parael di6,metrodelcubodela cajadeMANT£NIMi£NTO LimpiezaReparaciones AccesoriosIdentificacion DEL Producto P61iza De GarantiaSAN LUlS POTOSI, SLP Para Otras LocalidadesDWE4557 ,..I,o.ml Garantia lirnitada por tres aosGarantia DE Reembolso DE SU Dinero POR go Dias Reemplazo Gratuito DE LAS Etiquetas DEDW4579 EspecificacionesDWE4557 DWE4599 DW4559Capable --CANNOT be Used Optimal

DWE4559CN specifications

The DeWalt DWE4559CN is a powerful and robust angle grinder designed for heavy-duty applications in various professional environments. Known for its reliability and performance, this tool is a favorite among contractors, metal workers, and DIY enthusiasts alike.

At the core of the DWE4559CN is a high-performance 4.0 HP motor that delivers impressive 6,000 RPM, providing the power needed to tackle even the most demanding grinding tasks. This grinder is equipped with a 9-inch wheel, making it ideal for cutting, grinding, and finishing a wide range of materials including metal, concrete, and masonry. The larger wheel size allows for greater material removal and improved efficiency.

One of the standout features of the DWE4559CN is its advanced overload protection mechanism. This technology prevents the motor from overheating by automatically shutting down the tool in case of excessive load conditions. This not only extends the lifespan of the grinder but also ensures safe operation during intense tasks.

Another noteworthy characteristic is the one-touch guard feature, which simplifies the process of adjusting the guard position without the need for additional tools. This ensures that users can quickly adapt the tool to various applications while maintaining safety. The grinder also includes a cast metal gear case that enhances durability and provides better protection against wear and tear in harsh working environments.

The DWE4559CN is designed with user comfort in mind, featuring an ergonomic handle and a two-position side handle for better control and reduced vibration during prolonged use. This enhances user comfort and reduces fatigue, allowing for extended working periods without compromising performance.

Furthermore, the grinder showcases a spindle lock button, making wheel changes quick and effortless. Its industry-standard 5/8-inch - 11 spindle thread accommodates a wide variety of grinding wheels, ensuring versatility in applications.

In summary, the DeWalt DWE4559CN angle grinder combines power, durability, and user-friendly features, making it an invaluable tool for professionals seeking reliability and efficiency in their grinding tasks. Its robust design and advanced technologies help ensure that users can tackle challenging projects with confidence and ease. Whether for industrial use or intensive DIY projects, the DWE4559CN stands out as a dependable choice.
Top Page Image Contents