DeWalt DWE4559CN instruction manual Mounting Cutting Wheels FIG, Using Cutting Wheels

Page 21

MOUNTINGCLOSED(TYPE1)GUARD

FIG,20

_N

1.

Open the guard latch (M), and align the

M

 

 

lugs (N) on the guard with the slots on

 

 

 

the hub (O). This will align the lugs with

 

 

 

slots on the gear case cover. Position

 

 

 

the guard facing backward.

 

 

 

2.

Push the guard down until the

guard

 

 

 

lug engages and rotates freely

in the

 

O

 

groove on the gear case hub.

 

 

 

3.

Rotate guard (F) into desired working

 

F

position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection.

4.Close the guard latch to secure the guard on the gear case cover. You should be unable to rotate the guard by hand when the latch is in closed position. Do not operate grinder with a loose guard or with the guard latch in open position.

5.To remove the guard, follow the procedure above in reverse order.

MOUNTING CUTTING WHEELS (FIG. 22)

CAUTION: Matching diameter threaded backing flange and clamp nut (included with tool) must be used for cutting wheels.

1.Remove soft mount (G).

2.Install wheel backing flange, aligning flats on spindle (X)with flats on backing flange (Q).

3.Place the wheel on the backing flange, centering the wheel on the backing flange pilot.

4.Install the clamp nut, ensuring that the wheel remains centered on the backing flange.

5.Depress the spindle lock button and tighten clamp nut with wrench.

6.Reverse the above procedure to remove the wheel.

FIG.22

NOTE" The guard is pre-adjusted to the FIG.21

 

diameter of the gear case hub at the factory.

P

If, after a period of time, the guard becomes

 

loose, tighten the adjusting screw (P) with

 

the guard latch in the closed position with

 

guard installed on the tool.

 

NOTICE: To reduce the risk of damage

to the tool, do not tighten adjusting screw with guard latch in open position. Undetectable damage to guard or mounting hub may result.

USING CUTTING WHEELS

i_,WARNING: Do not use edge grinding/cutting wheels for surface grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage and injury may result.

1.Allow tool to reach full speed before touching tool to work surface.

2.Apply minimum pressure to work surface, allowing tool to operate at high speed. Cutting rate is greatest when the tool operates at high speed.

2O

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Heavy Duty Large Angle Grinders General Power Tool Safety Warnings Definitions Safety GuidelinesWork Area Safety Electrical SafetyUse Common Stay alertDo not For yourService Safety iNSTRUCTiONS forALL Operations Abrasivej Cuing-OffOperationsPosition the cord clear of the spinning accessory. /f you Regularly clean the power tools air vents. The motorsKickback and Related Warnings Safety Warnings Specific for Polishing Operations Additional Safety Warnings Specific forSafety Warnings Specific for Sanding Contactwithwheel,andsparksthatcouldigniteclothingSafety Warnings Specific for Wire Additional Safety Rules for GrindersBrushing Operations Future USE Save These iNSTRUCTiONS forFamiliarization Dust Ejection SystemToughcord TM System AttacMng Switch Protection TMSide Handle Fig DWE4597, DWE4597N, DWE4599NWheel Mountin9 Accessories Attachments FIG3. \Attach M Ents Mounting Guard Sanding Flap DiscsMounting and Removing Guard Grinding Wheels Sanding Discs Type28hubbedwheelWire Wheels Flaring Cup StonesWheels Operation Switch FigReduce WhenSpindle Lock Button FIG Trigger Operation with LOCK-ONFEATUREMounting and Removing Hubbed Wheels Mounting NON-HUBBED WheelsMounting Sanding Backing Pads FIG ThewheeltostoprotatingbeforelayingthetooldownUsing Sanding Backing Pads FIG Precautions To Take When Sanding PaintEnviron M Ental Safety SandingdiscwhiledepressingthespindlelockbuttonCleaning and Disposal Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels DustoutsidetheworkareaMounting and Using Flaring Cup Mounting and Using Cutting Type 1 WheelsUsing a Flaring CUP Wheel FIG Mounting Flaring CUP Wheel Guard FIGMounting Cutting Wheels FIG Using Cutting WheelsThewheeltobendandmaycausewheelbreakage MaintenanceRepairs Register OnlineThree Year Limited Warranty Year Free ServiceDAY Money Back Guarantee Aver*issernents de scurit gnraux Dfinitions Iignes directrices en rnatire de scuritET Toutes LES Directives Pour UN Usage Ulterieur Pour les outils lectriquesNepas exposerlosoutils61ectriques b la pluie ou b SECURITi PersonnelleUtilisation ET Entretien Dunoutil ¢LECTRIOUE BNepas utiliserun outil61ectrique dent Iinterrupteur Toutes L£S Operations#PARATION Page Rebonds eft avertissernents all, rents NNepasfairefonctionnerIoutil61ectrique b proximit6 deAvertissements de scurit spcifiques Aux operations de rneulage et de coupe Par abrasionSupplrnentaires spcifiques aux Avertissernents de scuritAux rneuleuses Rgles additionnelles de scurit propresNon recommande ULT E-RIEURE Conserver CES Consignes PourRoute PendantPOIGN#E Arriere ANTI-VIBRATIONS FIG Description j 9Systeme DI#VACUATION DES Poussieres Carter AutomatiqueLaterale H peut tre installee sur Iun ou Installation De la poigne LatraleEmbrayage =CLUTCH Mc DWE4597, DWE4597N, DWE4599NInstallation de rneules et daccessoires Positionnement de la poigne artisteSEU LEM ENT Disques de pon age , feuillets ¢¢I=SSOI R I=SDewalt D284938po D284937po D284939po Type27hubbedwheelMeuleavecmoyeun28 MeulesBrosses mdtalliques Meules boisseauxMeules abrasives Assemblage ET Retrait DU Capot Protecteur Assemblage du capot protecteurFonctionnement Interrupteur FigUtilisation DE Linterrupteur a Gachette Installation ET Reftrait DES Meules Avec Moyeu Installation DES Meules Sans MoyeuMeulage DE Surface Avec DES Meules FIG Meulagede Chant Avec DES Meules FIG Toutenenfonantleboutondeverrouillage LetamponSLa brochetouten tournantle disque Abrasifjusquce quele disqueetSECURITiPERSONNELLE Respect DE LenvironnementNettoyage ET Mise AU Rebut Brosses Mtalliques a Touret FIG Utilisation DE Brosses Forme Coupelle ET DEMontage et utilisation de meules INSTALLATiON DES MeulesBoisseaux Coniques FIG Montage DU Capot Protecteur FERM¢ DE TypePourretirerlecapotprotecteur,degager Montage DE Disques DE Coupe FIGUtilisation DE Disques DE Coupe Accessoires NeoyageRparations Garantie lirnite de trois ans Remplacement Gratuit DES EtiquettesContrat Dentretien Gratuit DUN AN Garantie DE Remboursement DE 90 JoursConserve Todas LAS Advebtencias Definiciones Normas de seguridadIADVERTENCIA! Lea todas las advertencias de seguridad Seguridad EN EL Area DE TrabajoUSO Y Mantenimiento DE LA Herramienta Electrica Seguridad PersonalInstrucciones DE Segubidad Paba Todas LAS Opebaciones Advertencias de seguridad comunes paraMantenimiento Page Bebote g advertencias relacionadas Para operaciones de pulido Advertencias de seguridad especificasNorrnas de seguridad adicionales para esrneriladoras Para operaciones de cepillado con cepillo de alarnbreLargo total RPM GUARD£ Estas Instrucciones Para Futuras ConsultasUSO Debido Switch Protection TM Proteccion DE Interruptor ElectronicoMango Trasero Antivibraciones FIG Sistema DE Extraccion DE PolvoFijaci6n MONTAJ£ Y AjustesMange =CLUTCH TMComo girar mango trasero Fig Rotaci6n de la caja de engranajes FigAccesorios y dispositivos para el montaje de los discos D28499 SolamenteDispositivos Sanding Flap DiscsGuardatipo28 D2849389 Guardatipo27 D2849377 D2849399 Discodetipo27Discotipo28 Discos de lijarCe illos de alambre Copa de PiedraDiscos de corse Montaje Y Extraccion DEL Protector Protector de rnontajeATENCI6N Accesorio podriaFUNCIONAMI£NTO Interrupter FigEncendido Permanente Instalacidn DE Discos CON Centro Deprimido Esmerilado DE Superficie CON Discos DE EsmerilarEsmerilado DE Bordes CON Discos DE Esmerilar FIG Montaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos DE Lijar FIGAl lijar pintura Precauciones que debe tenet en cuentaUSO DE Almohadillas DE Respaldo Para Lijar FIG Seguridad PersonalBeberofumarNosedebendejarartculosparacomer,beber Discos AlambreReducir Alambre. PuedenAplicarlalasuperficiedetrabajo Permitaquelaherramientaalcancelavelocidadm6,ximaantesdeSobreunasuperficie Instalaci6n y utilizaci6n de piedrasSeextiendaApretarfirmementelostornillosdelacamisadelaguarda AntesdeusarelesmeriladorMontaje y uso de discos de corte Tipo 1MANT£NIMi£NTO Parael di6,metrodelcubodela cajadeLimpieza Montaje DE LOS Discos DE Corte FIGReparaciones AccesoriosSAN LUlS POTOSI, SLP P61iza De GarantiaPara Otras Localidades Identificacion DEL ProductoGarantia DE Reembolso DE SU Dinero POR go Dias Garantia lirnitada por tres aosReemplazo Gratuito DE LAS Etiquetas DE DWE4557 ,..I,o.mlDWE4557 DWE4599 EspecificacionesDW4559 DW4579Capable --CANNOT be Used Optimal

DWE4559CN specifications

The DeWalt DWE4559CN is a powerful and robust angle grinder designed for heavy-duty applications in various professional environments. Known for its reliability and performance, this tool is a favorite among contractors, metal workers, and DIY enthusiasts alike.

At the core of the DWE4559CN is a high-performance 4.0 HP motor that delivers impressive 6,000 RPM, providing the power needed to tackle even the most demanding grinding tasks. This grinder is equipped with a 9-inch wheel, making it ideal for cutting, grinding, and finishing a wide range of materials including metal, concrete, and masonry. The larger wheel size allows for greater material removal and improved efficiency.

One of the standout features of the DWE4559CN is its advanced overload protection mechanism. This technology prevents the motor from overheating by automatically shutting down the tool in case of excessive load conditions. This not only extends the lifespan of the grinder but also ensures safe operation during intense tasks.

Another noteworthy characteristic is the one-touch guard feature, which simplifies the process of adjusting the guard position without the need for additional tools. This ensures that users can quickly adapt the tool to various applications while maintaining safety. The grinder also includes a cast metal gear case that enhances durability and provides better protection against wear and tear in harsh working environments.

The DWE4559CN is designed with user comfort in mind, featuring an ergonomic handle and a two-position side handle for better control and reduced vibration during prolonged use. This enhances user comfort and reduces fatigue, allowing for extended working periods without compromising performance.

Furthermore, the grinder showcases a spindle lock button, making wheel changes quick and effortless. Its industry-standard 5/8-inch - 11 spindle thread accommodates a wide variety of grinding wheels, ensuring versatility in applications.

In summary, the DeWalt DWE4559CN angle grinder combines power, durability, and user-friendly features, making it an invaluable tool for professionals seeking reliability and efficiency in their grinding tasks. Its robust design and advanced technologies help ensure that users can tackle challenging projects with confidence and ease. Whether for industrial use or intensive DIY projects, the DWE4559CN stands out as a dependable choice.
Top Page Image Contents