Cisco Systems 1700 manual Connecting Power to the Router

Page 40

Chapter 2 Installing the Cisco 1700 Router

Connecting Power to the Router

Read the following warnings before connecting the router to power.

Warning The power supply is designed to work with TN power systems.

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 15AU.S. (240VAC, 16A international) is used on the phase conductors (all current-carrying conductors).

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.

Take the following steps to connect power to the router and to turn the router on:

Step 1 Connect the attached power-supply cord to the power socket (labeled +5,+12,-12 VDC) on the router rear panel.

Step 2 Connect one end of the separate power cord to the socket on the power supply.

Step 3 Connect the other end of the separate power cord to a power outlet.

Step 4 Press the router power switch to ON ( ).

Step 5 Confirm that the router has power by checking that the

PWR LED on the front panel is on.

 

Cisco 1700 Router Hardware Installation Guide

2-8

78-5405-03

Image 40
Contents Cisco 1700 Router Hardware Installation Guide Corporate HeadquartersPage Cisco 1700 Router Hardware Installation Guide Page N T E N T S Wall-Mounting Troubleshooting Vii Viii About This Guide Audience and ScopeOrganization Related PublicationsConventions Xii Xiii Cisco.com Obtaining DocumentationDocumentation DVD Cisco Product Security Overview Documentation FeedbackOrdering Documentation Reporting Security Problems in Cisco Products PsirtObtaining Technical Assistance Cisco Technical Support WebsiteSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information Cisco 1700 Router Hardware Installation Guide 78-5405-03 Cisco 1700 Router Overview Cisco 1700 Router Key Features Key FeaturesFeature Description Connector/Slot Label/Color Description Rear-Panel ConnectorsRear-Panel Ports and LEDs Rear-Panel LEDs LED Label Color DescriptionFront-Panel LEDs PWRACT COLACT/CHØ ACT/CH1Router Memory Types of MemoryAmounts of Memory 1700# show versionRouter Box Contents Equipment When You Use ItUnpacking the Router Additional Required EquipmentHardware Installation Guide that comes with every card NT1Cisco 1700 Router Overview Installing the Cisco 1700 Router Before Installing the RouterConnecting the Router to Your Local Network Connecting the Router to the Local Network Installing WAN Interface Cards Safety InformationInstalling a WAN Interface Card Installing the Cards in Correct SequenceInstalling the Cards Inserting a WAN Interface Card in the Router Connecting Power to the Router Connecting the Power Supply Verifying Your Installation Optional Installation Steps Connecting a PCConnecting a Modem Connecting the Console Cable to the RouterConnecting a Modem to the Router Wall-Mounting Wall-Mount Brackets-Bottom of RouterInstalling the Cisco 1700 Router Installing the Cisco 1700 Router Troubleshooting Contacting Cisco or Your ResellerRecovering a Lost Password Change the Configuration RegisterConfiguration register is Reset the Router Reset the Password Problem Solving Reset the Configuration Register ValueOK LED Diagnostics Troubleshooting WAN Interface Cards and CablesOK LED Blinking Patterns Number of Blinks MeaningTroubleshooting WAN Interface Cards Symptom Possible CausesSymptom Possible Causes Troubleshooting the Power SystemTroubleshooting the Power System Troubleshooting Isdn Isdn S/T Isdn UTroubleshooting Isdn Use show isdn statusTable A-1 Router Specifications Description SpecificationAppendix a Technical Specifications Cabling Specifications Ethernet Cables RJ-45 Pin Signal DirectionTX+ RX+ Specification 10BaseT 100BaseTX Ethernet Network Cabling GuidelinesConsole Cable and Adapters Table B-2 Ethernet Cabling GuidelinesSignal RJ-45 Pin DB-9 Pin DB-25 Pin Table B-3 Console Cable and Adapter PinoutsConsole Terminal Port Console Cable AdapterInstalling and Upgrading Router Memory Opening the Chassis Figure C-1 Removing the Chassis Screws Locating Memory Figure C-2 Cisco 1700 Motherboard-Memory LocationsInstalling a Mini-Flash Module Figure C-3 Mini-Flash ModuleFigure C-4 Installing a Mini-Flash Module Removing a Mini-Flash ModuleInstalling a Dimm Figure C-5 Removing a Mini-Flash ModuleFigure C-6 Installing a Dimm Closing the ChassisFigure C-7 Closing the Chassis Appendix C Installing and Upgrading Router Memory Ordering and Configuring an Isdn Line Isdn BRI Line Configuration RequirementsTable D-1 Isdn BRI Switch Types Isdn BRI Switch TypesSwitch Type Keywords Isdn BRI Provisioning by Switch Type Table D-2 Isdn Provisioning by Switch TypeSwitch Type Provisioning Mterm =Defining Isdn Service Profile Identifiers Isdn Configuration Options Snapshot RoutingBandwidth on Demand and Dial Backup Dial-on-Demand RoutingNumerics IN-2 IN-3 IN-4 IN-5 IN-6
Related manuals
Manual 12 pages 24.76 Kb Manual 14 pages 20.45 Kb Manual 85 pages 32.54 Kb