Cisco Systems 1700 manual Verifying Your Installation

Page 42

Chapter 2 Installing the Cisco 1700 Router

Verifying Your Installation

You can verify that you have correctly installed the router by checking the following LEDs:

•PWR (front panel)—On when power is being supplied to the router.

•OK (front panel)—On when the router software is loaded and functional. Blinking means that the router is performing a power-on self-test (POST).

•WICØ/WIC1 OK (rear panel)—On when a WAN interface card is correctly installed in the corresponding WAN interface card slot.

•ETH ACT (front panel)—Blinking when there is network traffic on the local Ethernet LAN.

•WICØACT or WIC1 ACT (front panel)—Varies depending on the WAN interface card installed. Refer to Table 1-3in the “Cisco 1700 Router Overview” chapter.

•LNK (rear panel)—On when the router is correctly connected to the local Ethernet LAN through the 10/100 ETHERNET port.

	Cisco 1700 Router Hardware Installation Guide
2-10	78-5405-03

Image 42

Contents Cisco 1700 Router Hardware Installation Guide Corporate HeadquartersPage Cisco 1700 Router Hardware Installation Guide Page N T E N T S Wall-Mounting Troubleshooting Vii Viii About This Guide Audience and ScopeOrganization Related PublicationsConventions Xii Xiii Obtaining Documentation Cisco.comDocumentation DVD Documentation Feedback Cisco Product Security OverviewOrdering Documentation Reporting Security Problems in Cisco Products PsirtObtaining Technical Assistance Cisco Technical Support WebsiteSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information Cisco 1700 Router Hardware Installation Guide 78-5405-03 Cisco 1700 Router Overview Cisco 1700 Router Key Features Key FeaturesFeature Description Rear-Panel Connectors Connector/Slot Label/Color DescriptionRear-Panel Ports and LEDs Rear-Panel LEDs LED Label Color DescriptionACT Front-Panel LEDsPWR COLACT/CHØ ACT/CH1Router Memory Types of MemoryAmounts of Memory 1700# show versionUnpacking the Router Router Box ContentsEquipment When You Use It Additional Required EquipmentHardware Installation Guide that comes with every card NT1Cisco 1700 Router Overview Installing the Cisco 1700 Router Before Installing the RouterConnecting the Router to Your Local Network Connecting the Router to the Local Network Installing WAN Interface Cards Safety InformationInstalling a WAN Interface Card Installing the Cards in Correct SequenceInstalling the Cards Inserting a WAN Interface Card in the Router Connecting Power to the Router Connecting the Power Supply Verifying Your Installation Optional Installation Steps Connecting a PCConnecting a Modem Connecting the Console Cable to the RouterConnecting a Modem to the Router Wall-Mounting Wall-Mount Brackets-Bottom of RouterInstalling the Cisco 1700 Router Installing the Cisco 1700 Router Troubleshooting Contacting Cisco or Your ResellerRecovering a Lost Password Change the Configuration RegisterConfiguration register is Reset the Router Reset the Password Problem Solving Reset the Configuration Register ValueOK LED Blinking Patterns OK LED DiagnosticsTroubleshooting WAN Interface Cards and Cables Number of Blinks MeaningTroubleshooting WAN Interface Cards Symptom Possible CausesTroubleshooting the Power System Symptom Possible CausesTroubleshooting the Power System Troubleshooting Isdn Isdn S/T Isdn UTroubleshooting Isdn Use show isdn statusTable A-1 Router Specifications Description SpecificationAppendix a Technical Specifications Cabling Specifications RJ-45 Pin Signal Direction Ethernet CablesTX+ RX+ Console Cable and Adapters Specification 10BaseT 100BaseTXEthernet Network Cabling Guidelines Table B-2 Ethernet Cabling GuidelinesConsole Terminal Signal RJ-45 Pin DB-9 Pin DB-25 PinTable B-3 Console Cable and Adapter Pinouts Port Console Cable AdapterInstalling and Upgrading Router Memory Opening the Chassis Figure C-1 Removing the Chassis Screws Locating Memory Figure C-2 Cisco 1700 Motherboard-Memory LocationsInstalling a Mini-Flash Module Figure C-3 Mini-Flash ModuleFigure C-4 Installing a Mini-Flash Module Removing a Mini-Flash ModuleInstalling a Dimm Figure C-5 Removing a Mini-Flash ModuleFigure C-6 Installing a Dimm Closing the ChassisFigure C-7 Closing the Chassis Appendix C Installing and Upgrading Router Memory Ordering and Configuring an Isdn Line Isdn BRI Line Configuration RequirementsIsdn BRI Switch Types Table D-1 Isdn BRI Switch TypesSwitch Type Keywords Switch Type Provisioning Isdn BRI Provisioning by Switch TypeTable D-2 Isdn Provisioning by Switch Type Mterm =Defining Isdn Service Profile Identifiers Isdn Configuration Options Snapshot RoutingBandwidth on Demand and Dial Backup Dial-on-Demand RoutingNumerics IN-2 IN-3 IN-4 IN-5 IN-6

Related manuals

Manual 12 pages 24.76 Kb

Manual 14 pages 20.45 Kb

Manual 85 pages 32.54 Kb