Delta 36-451X, 36-441B instruction manual Unpacking and Cleaning

Page 8

UNPACKING AND CLEANING Continued

16A

16

1

4

21* 20*

19*

17

16B

2*

3*

5

18	14	9
15	13

12	11

6

10

7*

8*

Fig. 2

1. Contractor’s Saw

2*. Blade Tilting Handwheel (Zinc plated on 36-451X)

3*. Handwheel Lock Knob (Zinc plated on 36-451X)

4.Blade Guard and Splitter Assembly

5.Table Insert

6.Miter Gage

7*. Miter Gage Handle (Zinc plated on 36-451X)

8*. Miter Gage Handle Cap (Only with Model 36-441-B)

9.Splitter Mounting Bracket

10.1/4-20 x 3/4" Hex Head Bolts (2)

11.1/4" Flat Washers (2)

12.5/16-18 x 5/8" Carriage Head Bolt

13.5/16" Flat Washer

14.5/16-18 Hex Nut

15.Arbor Wrenches (2)

16.Cast Iron Extension Table (36-451X only) 16A. Steel Extension Table (36-441B only)

16B. Extension Table Support Back Rail(36-441B only)

17.7/16-20 x 1-3/4" Hex Head Bolts for assembling extension table (3)

18.7/16 Flat Washers for assembling extension table (3)

19*. 5/16-18 x 1" Flat head Screw (3) (36-451X only) -or-3/8-16 x 1" Hex head Bolt (4) (36-441B only)

20*. 5/16 Flat Washer (3) (36-451X only) -or-3/8-16 Hex Nut (4) (36-441B only)

21*. 5/16-18 Hex Nut (3) (36-451X only) -or-3/8 Flat Washer (4) (36-441B only)

8

Image 8

Contents Contractor’s Saw Important Safety Instructions Safety Guidelines DefinitionsGeneral Safety Rules Stay ALERT, Watch What YOU are DOING, Additional Safety Rules for Contractor SAW Properly Support Long or Wide workpiecesGrounding Instructions Power ConnectionsMotor Specifications Extension Cords Volt Minimum Gauge Extension CordForeword Unpacking and CleaningFunctional Description Unpacking and Cleaning Rear Leg Panel Assembling SAW to Stand SAW AssemblyAssembling SAW Stand Motor Assembly Disconnect Machine from the Power SourceAssembling Blade Tilting Handwheel Assembling Motor to Motor Mounting PlateDisconnect Machine from Power Source Assembling Motor and Motor Mounting Plate to SAWAssembling Motor PULLEY, Belt Pulley GUARD, and Drive Belt To Motor Mounting PlateConnecting Motor Cord to Switch Assembly Illustrates the motor cord connected to the switch assemblyAssembling and Aligning Blade Guard and Splitter Assembly Assembling Blade Guard Splitter AssemblyIf alignment is necessary, loosen the two screws Page Extension and Switch Assembly Assembling Steel Extension Wing and Switch Model 36-441BAssembling Switch to Cast Iron Extension Wing Assembling Cast Iron ExtensionFastening Stand to Supporting Surface Operating ControlsOperation and Adjustments Adjusting 90 Degree and 45 Degree Positive StopsRaising and Lowering Blade Tilting the BladeBlade Alignment Adjusting Blade AlignmentChecking Blade Alignment Changing SAW Blade Backlash AdjustmentsAdjusting Blade Tilting Mechanism Adjusting Table Insert Miter Gage Operation and AdjustmentCROSS-CUTTING Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGCommon Sawing Operations Ripping Constructing a Push StickAccessory Moulding Cutterhead Using Moulding CutterheadAccessory Dado Head Using Dado HeadPower Tool Institute Constructing a FeatherboardPushstick Constructing a Push StickMaintenance StorageDust Chute Repositioning Motor For StoragePARTS, Service or Warranty Assistance AccessoriesCanadian PORTER-CABLE Delta Service Centers