Grizzly G0458 instruction manual Paper Replacement, Tools Needed Qty

Page 24

Paper Replacement

Tools Needed:

Qty

Flat Head Screwdriver

1

Hex Wrench 4mm

1

Hex Wrench 5mm

1

Carton Cutter or Utility Knife

1

The Model G0458 is designed for 3" wide sand- paper rolls. Turn to SECTION 5: ACCESSORIES on Page 24 for grit selection and model num- bers.

To change the paper:

1.Disconnect power to the sander!

2.Open the top cover, remove the three cap screws that secure the chip deflector to the sander frame, and set the deflector aside.

3.Loosen the cap screw on the right spring- loaded clamp as shown in Figure 18.

 

Right

 

Clamp

 

Tension

Access

Wheel

Hole

 

Figure 18. Loosening cap screw on right spring-

loaded clamp.

4.Remove the sandpaper from the clamp.

Note: You can use a flat head screwdriver to loosen the clamp to free the sandpaper.

5.Rotate the drum to remove the sandpaper belt.

6.Loosen the cap screw on the left clamp and remove the sandpaper.

7.Use the old sandpaper as a pattern, or use the pattern in Figure 19, to cut a new piece of sandpaper to the necessary shape. After cutting the 1212" angled sides, measure 1" along the same sides and cut off the ends with a knife.

��

 

��

��

��

 

 

 

 

 

 

 

 

��

 

���

 

Figure 19. Sandpaper pattern.

8.Insert the left corner of the new sandpaper into the left clamp and tighten the cap screw as shown in Figure 20. The angled side of the sandpaper must be flush with the left drum edge. If the sandpaper overlaps the edge, you may have difficulty closing the cover.

Left

Clamp

Figure 20. Securing sandpaper in left clamp.

-22-

G0458 18" Open End Belt/Drum Sander

Image 24
Contents Open End Drum Sander Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders Circuit Requirements 110V OperationSET UP Set Up SafetyItems Needed for Set Up UnpackingInventory Box 1 Figures 1 QtyHardware Recognition Chart Site Considerations StandComponents and Hardware Needed Qty To assemble the standPage Installing Sander on Stand To install the sander on the standTilting sander upright G0458 18 Open End Belt/Drum Sander To install the handwheel To install the dust portHandwheel Dust Port and BagDust Collection Test Run To connect the dust ports to a dust collectorRecommended Adjustments Operation Safety Depth of Cut OperationsTo set the depth of cut To adjust the feed belt speed Variable Speed SandingTo sand a workpiece Sanding Tips Choosing SandpaperGrit Class Usage Paper Replacement To change the paper Disconnect power to the sanderTools Needed Qty Page Accessories G3640-Power Twist V-Belt 1⁄2 xPRO-STICKSanding Pad SizeMaintenance CleaningDaily Checks and Maintenance ScheduleSanding Belts Feed belt drive chainBelt Tensioning Checking V-belt tension with a Straightedge and a rulerService TroubleshootingSanding Operations To replace the V-belts Disconnect power to the sander Replacing V-BeltsTo align the pulleys Disconnect power to the sander Pulley AlignmentFeed Belt Tracking To track the feed beltFeed Belt Tension To tension the feed beltFeed Belt Replacement To replace the feed belt Disconnect power to the sanderTable Adjustments To align the drums Disconnect power to the sanderGauge Blocks To make the gauge blocksPressure Plate Adjustments Plate Adjustment Wiring Diagram G0458 Parts Breakdown G0458 Parts List DescriptionMotor Bracket Chip Deflector Plate Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog