Grizzly G0527 instruction manual Maintenance, GeneralSchedule

Page 25

SECTION 7: MAINTENANCE

GeneralSchedule

Your safety is important! Please follow the warnings below during this entire section:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Disconnect power to the

ON

 

 

machine when perform-

 

 

 

 

 

 

 

 

ing maintenance, assem-

OFF

 

 

bly or adjustments.

 

 

Failure to do this may

 

 

 

 

 

 

 

 

 

 

 

result in serious person-

 

 

 

 

al injury.

 

 

 

 

 

 

 

Loose hair and clothing could get caught in machinery causing seri- ous personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery.

Wear safety glasses dur- ing the entire mainte- nance process. Failure to comply may result in serious personal injury.

The following items should be checked each time the sander is used:

Loose mounting bolts.

Damaged sanding belt.

Worn or damaged wires.

Air line water collection cup is filled with water.

Any other condition that could hamper the safe operation of this machine.

Weekly:

Grease the eight fittings located on the feed belt roller axles and the sanding belt roller axles. They are identified with yellow stick- ers.

Monthly:

Apply a generous amount of grease to the table elevation screws. Be sure to cover the adjustment screws with the dust covers when finished.

Remove the lower side panel to access the table lifting mechanism. Apply a generous amount of grease to the chain and gears associated with the table lifting mechanism. Be careful to not get grease on any of the V- belts. This could cause them to slip off their pulleys.

Apply a generous amount of multi-purposed grease to the table drive chain and sprocket assembly.

G0527 18" Wide Belt Sander

-23-

Image 25
Contents Wide Belt Sander Page Table Of Contents Safety Instructions For Power Tools SafetyLength Additional Safety For Wide Belt Sanders Commentary IntroductionAmperage Draw Circuit RequirementsCircuit Breaker Connection TypeGrounding Minimum Cord Size Extension CordsExternal Features Machine FeaturesControl Panel Access Doors Page G0527 Inventory SET UPFollowing parts shown in should be enclosed Bolt Measure Hardware Recognition ChartWorking Clearance Clean Up Site ConsiderationsWork Area Lightening Beginning Assembly Floor Mounting To hook up the air line Air Line Hook-Up Dust CollectionTo hook up the dust collection system Sanding Belt Proper position of belt between Limit switchesPressure Rollers Recommended adjustment checklist Recommended AdjustmentsBefore Sanding OperationsChoosing Sandpaper GritControls for adjusting Table height Table Movement Adjusting Feed RateNormal Operating Load Amperage Meter Sanding WorkpieceGeneralSchedule MaintenanceServicing Brakes Air Circuit Filters Clean Sanding Belts Date Approximate Hours Of Use Maintenance Performed Maintenance LogCalibration Service AdjustmentsFeed Belt Tracking Feed Belt TensionTo check the sanding belt oscillation Belt OscillationTable Parallelism To adjust the table parallelismPressure Rollers Air System Belt AdjustmentPeriodically inspect the following Air Line Circuit Date Approximate Hours Of Use Service Performed Service LogCleaning Pads Aftermarket AccessoriesReference Info GeneralMachine Data Sheet Description Parts Diagrams & Lists1305 1308 Machine Frame 2101 2202 2103 Elevation Screw 3132 Conveyor Table Spring Ball Bearing UCC206 Page Square Frame Machine ID Label Page Electrical Control BOX Page Filter CUP 1⁄4 Symptom Possible Cause Corrective Action Machine TroubleshootingTion Sanding TroubleshootingPage Page G0527 18 Wide Belt Sander Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage #ALL 4ODAYD&ORO