Schumacher SSF-1000A owner manual Using Your Battery Charger, Completion of Charging Charge

Page 11

USING YOUR BATTERY CHARGER

OVERVIEW

Using the battery charger is very simple. First, connect the battery and AC power following the precautions listed under “OPERATING INSTRUCTIONS”. Then select the appropriate BATTERY TYPE and CHARGE RATE for your battery. The charger will then do everything automatically. This section explains a few details.

CHARGING: If the charger does not detect a properly connected battery, the CHECK (red) LED will light continuously until a battery is detected. Charging will not begin while the CHECK light is on. When charging begins, the CHARGING LED will be lit.

AUTOMATIC SHUT OFF: When the 2A, 6A, or 10A charge rate is selected, the charger is set to perform an automatic charge. When an automatic charge is performed, the charger stops charging automatically after the battery is fully charged.

ABORTED CHARGE: If charging can’t be completed normally, charging will be aborted. When charging is aborted, the charger’s output is shut off and the red CHECK LED and digital LED blink on and off (at opposite times). In that state, the charger ignores all buttons. To reset from after an aborted charge, either disconnect the battery or unplug the charger.

DESULFATION MODE: If a battery is left discharged for an extended period, it could become sulfated and not accept a normal charge. If the charger detects a sulfated battery, the charger will switch to a special mode of operation designed for such batteries. Activation of the

special desulfation mode is indicated by blinking the CHARGING LED. If successful, normal charging will resume after the battery is desulfated. The CHARGING LED will then stop blinking and light continuously. Desulfation could take up to 10 hours. If desulfation fails, charging will be aborted and the CHECK (red) LED will blink.

COMPLETION OF CHARGING: Charge

completion is indicated by the CHARGED (green) LED; when lit, the charger has stopped charging and switched to the Maintain Mode of operation.

MAINTAIN MODE: When the CHARGED (green) LED is lit, the charger has started Maintain Mode. This mode of operation is also known as Float-Mode Monitoring. In this mode, the charger keeps the battery fully charged by delivering a small current, when necessary. The voltage is main- tained at a level determined by the BATTERY TYPE selected.

GENERAL CHARGING NOTES:

The charger is designed to control its cooling fan for efficient operation. Consequently, it is normal for the fan to start and stop when maintaining a fully charged battery. The fan does not normally run in Tester Mode.

If the charge mode is changed after charging has started (by pressing the CHARGE RATE or BATTERY TYPE button), the charging process will be restarted.

The voltage displayed during charging is the charging voltage and usually will be higher than the battery’s resting voltage.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Send Warranty Product Repairs to Table of Contents Help US Help YOU Important Safety InstructionsPersonal Safety Precautions Plugging IT Before Using Your Battery ChargerPreparing Your Battery to be Charged Using AN Extension CordNegative Grounded System Charging Battery in the VehicleOperating Instructions Charging Battery Removed from the Vehicle Speedcharge Control SSF-1000A Control Panel Display Mode SwitchCharge Rate Switch Battery Type SwitchControl Panel Guide SSF-1000A Control Panel GuideUsing the BUILT-IN Battery Tester General Charging Notes Using Your Battery ChargerCompletion of Charging Charge Charging Tips Maintenance and CareKnow Your Charger Battery Percent and Charge Time Problem Possible Cause Solution TroubleshootingPage Limited Warranty Faire parvenir les produits à réparer sous garantie à Manuel d’utilisationUtilisation DU Testeur DE Batterie Intégré Table DES MatièresAIDEZ-NOUS À Vous Aider N’oubliez pas Consignes DE Sécurité ImportantesConservez CES Instructions Mesures DE Sécurité Personnelles Utilisation D’UNE Rallonge Avant D’UTILISER LE Chargeur DE BatteriePréparer LA Batterie Pour LA Charge BranchementBranchement à un circuit à masse Consignes D’UTILISATIONCharge DE LA Batterie Dans LE Compartiment Moteur Circuit À Masse NégativeOrdinaire Charge DE LA Batterie SUR LA Terre FermeDécharge Poussée Les batter- ies à décharge poussée portent Tableau DE Commande DU ChargeurCommutateur DE Taux DE Charge Commutateur DE Type DE BatterieFii Guide Tableau DE CommandeUtilisation DU Testeur DE Batterie Intégré Page Utilisation DU Chargeur DE Batterie Protection contre la surchauffe Ce SE Familiariser Avec LE ChargeurConseils Pour LA Charge EntretienPourcentage ET Temps DE Charge Anomalie Cause Probable Correctif Tableau DE DépannageGarantie Limitée

SSF-1000A specifications

The Schumacher SSF-1000A is a state-of-the-art electric scooter designed for riders seeking a combination of power, efficiency, and modern technology. This innovative model showcases a sleek design, highlighting its user-friendly features and advanced engineering.

One of the standout aspects of the SSF-1000A is its powerful 1000W motor, which provides impressive acceleration and a top speed of up to 28 mph. This makes it an ideal choice for both urban commuting and recreational riding. The scooter’s robust performance is complemented by its high-capacity lithium-ion battery that offers a range of up to 40 miles on a single charge, allowing users to travel longer distances without the need for frequent recharging.

The SSF-1000A is equipped with a dual braking system, combining both electronic and mechanical brakes for enhanced safety and reliability. This braking system ensures smooth stopping power, providing riders with peace of mind, especially when navigating busy streets or steep inclines. The scooter also features front and rear LED lights, enhancing visibility during nighttime rides.

In terms of comfort, the SSF-1000A boasts an adjustable suspension system that absorbs bumps and uneven terrain, making it easier to ride over various surfaces. The wide, anti-slip deck offers ample foot space, promoting stability and balance, which is especially beneficial for newer riders. The scooter also comes with a lightweight aluminum frame, making it easy to carry and store.

One of the most notable technological advancements in the SSF-1000A is its smart display panel, which provides real-time information including speed, battery level, and distance traveled. This intuitive interface allows riders to monitor their performance at a glance. Additionally, the scooter supports Bluetooth connectivity, enabling users to pair their smartphones and access navigation features and ride statistics through a dedicated app.

The Schumacher SSF-1000A is not just about performance; it also reflects a commitment to sustainability. Its electric nature means zero emissions, making it an environmentally friendly alternative to traditional gasoline-powered vehicles. Overall, the SSF-1000A combines practicality, cutting-edge technology, and eco-friendly design, making it a top contender in the electric scooter market. Whether for daily commutes or leisure rides, this scooter stands out as a reliable and efficient choice for modern riders.
Top Page Image Contents