Charging the Battery Pack Figure B | Black & Decker PD400, 90544571

90544571 PD400 clutch sc 5/22/09 7:46 AM Page 6

CHARGING THE BATTERY PACK (FIGURE B)

THE SCREWDRIVER IS NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THE SCREWDRIVER, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.

The charger (8) is designed to use standard B household 120 volt 60 Hz power.

1.Insert the charger plug (9) into the charger port (7) as shown in figure B.

2.Plug the charger (8) into any standard 120 Volt 60 Hz electrical outlet and let the tool charge initially for 17 hours. A minimum

	charge time of 17 hours is required to	9
	recharge a completely discharged tool.	7
	NOTE: Do not charge by means of an
	engine generator or DC power source.	8
	Use only 120V AC.	8
	Use only 120V AC.

3.Disconnect the charger from the outlet, then disconnect the charger from the tool.

CAUTION: Do not use the tool while it is connected to the charger.

IMPORTANT CHARGING NOTES

1.Longest life and best performance can be obtained if the tool is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the tool in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the batteries.

2.While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.

3.If the batteries do not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and tool to a surrounding air temperature of 40°F (4,5 °C) to 105°F (+40,5 °C). (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the tool and charger to your local Black & Decker service center. See Tools Electric in yellow pages.

4.The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its batteries in a depleted condition.

5.To prolong battery life, avoid leaving on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall battery life.

6.The batteries will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries.

7.Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when not plugged into tool. Unplug charger before attempting to clean.

8.Do not immerse charger in water or any other liquid.

Safety Warnings and Instructions: Drilling

• Hold tool firmly to control its twisting action.

WARNING: Tool may stall (if overloaded or improperly used) causing a twist. To reduce the risk of injury always expect the stall. Grip the tool firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.

PD400, 90544571 specifications

The Black & Decker 90544571, PD400 is an innovative power tool designed for both amateur and professional users who demand top-notch performance and reliability. This versatile tool stands out with its robust construction and user-friendly features, making it an indispensable part of any toolkit.

One of the key features of the PD400 is its powerful motor that delivers excellent torque and speed, enabling users to tackle a wide variety of tasks with ease. Whether you're driving screws, drilling into wood, or tackling tougher materials, this tool provides the power needed for efficient operation. The ergonomic design ensures comfort during prolonged use, reducing hand fatigue and improving overall control.

The PD400 incorporates a 20-position clutch, offering precise control over drilling depths and allowing for adjustable torque settings. This feature is particularly valuable for users who want to avoid damaging materials or overdriving screws. Additionally, the dual speed control allows users to select between high and low-speed settings, providing versatility for both delicate work and heavy-duty applications.

Another highlight of the Black & Decker 90544571 is its lightweight design, which enhances portability and ease of handling. Despite its compact size, it doesn't compromise on power, making it perfect for both home improvement tasks and professional jobsites. The built-in LED work light illuminates dark or tight spaces, ensuring visibility and precision even in less-than-ideal conditions.

The PD400 comes equipped with a keyless chuck, making bit changes quick and effortless, thus enhancing productivity. For added convenience, it includes a built-in battery indicator that allows users to keep track of charge levels, ensuring that the tool is always ready to perform when required.

In terms of safety, the PD400 features an integrated brake, which stops the drill quickly when the trigger is released. This prevents accidents and provides additional peace of mind during operation. The durable construction ensures that the tool can withstand the rigors of daily use, rendering it a long-lasting investment.

In summary, the Black & Decker 90544571, PD400 is a feature-rich, reliable power tool that offers a perfect blend of power, precision, and user convenience. Its advanced technologies and thoughtful design make it an excellent choice for DIY enthusiasts and professionals alike, providing the performance required for an array of drilling and driving tasks.