Black & Decker 90544571, PD400 Maintenance, Accessories, Problem Possible Cause Possible Solution

Page 9

90544571 PD400 clutch sc 5/22/09 7:46 AM Page 9

•DO NOT CLICK THE TRIGGER OF A STALLED TOOL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE TOOL CAN RESULT. To remove, twist the bit back and forth and straight out.

•Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole.

•Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

•Make sure switch turns tool on and off.

WARNING: It is important to support work properly and to hold the tool firmly to prevent loss of control which could cause personal injury.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

Troubleshooting

Problem

Possible Cause

Possible Solution

• Tool will not charge.

• Charger not plugged into

• Plug charger into a

 

a working outlet.

working outlet. Refer to

 

 

“Important Charging

 

 

Notes” for more details.

 

 

• Check current at

 

 

receptacle by plugging in

 

 

a lamp or other appliance.

 

 

• Check to see if

 

 

receptacle is connected to

 

 

a light switch which turns

 

 

power off when you turn

 

 

out the lights.

 

• Surrounding air temperature

• Move charger and tool

 

too hot or too cold.

to a surrounding air

 

 

temperature of above 40

 

 

degree F (4,5°C) or below

 

 

105 degree F (+40,5°C).

• Tool will not drill.

• Clutch collar in wrong

• Move collar position to

 

position.

drill bit icon.

• Screws stripping

• Clutch collar setting

• Move collar position to

 

too high.

a lower setting.

• Screws not fully seated.

• Clutch collar setting

• Move collar position to

 

too low.

a higher setting.

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

BATTERY REMOVAL

Before attempting to disassemble this tool, turn it on and run it in either direction until it stops to ensure a complete discharge of the batteries. Using a phillips screwdriver, remove the screws from the product housing and take the two body halves apart. Lift the batteries out and pull off the terminal clips. See “Service Information” for battery replacement and RBRC for battery recycling.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents VEA EL Español EN LA Contraportada Please Read Before Returning this Product for ANY ReasonWork area safety General Safety RulesSpecific Safety Rules Functional Description Wire Size AWG Safety Warnings and Instructions ChargingCharging the Battery Pack Figure B Engine generator or DC power source Use only 120V ACImportant Charging Notes Inserting and Removing Bits Figure C Assembly and AdjustmentPivoting the Tool Head Figures D, E Press the pivot release button 3 shown in figure DOperating Instructions Accessories MaintenanceProblem Possible Cause Possible Solution Battery RemovalService Information Full TWO-YEAR Home USE Warranty For Service & SalesRbrc Seal DE Catalogue PD400 Conserver CES Directives Règles de sécurité générales90544571 PD400 clutch sc 5/22/09 746 AM Lignes Directrices EN Matière DE Sécurité Définitions Règles DE Sécurité SpécifiquesDescription Fonctionnelle Calibre de fil minimum recommandé pour les rallongesLongueur totale de la rallonge Calibre AWGRemarques Importantes SUR LE Chargement Chargement DU BLOC-PILES Figure BAssemblage ET Réglage Insertion ET Retrait DES Embouts Figure CPivotement DE LA Tête DE L’OUTIL FIG. D, E Directives D’UTILISATION AvertissementsMise EN Marche ET Arrêt FIG. G Vissage AccessoiresPerçage Conseils Pratiques Généraux Pour LE PerçageRetrait DES Piles Problème Cause possible Solution possibleInformation SUR LES Réparations Manual DE Instrucciones DEL Destornillador Inalámbrico Conserve Estas Instrucciones Normas generales de seguridadEsto garantizará la seguridad de la herramienta eléctrica Pautas DE SEGURIDAD/DEFINICIONES Normas DE Seguridad EspecíficasInstrucciones Y Advertencias DE Seguridad Carga Descripción DE LAS FuncionesNotas Importantes Sobre LA Carga Carga DEL Paquete DE Baterías Figura BInserción Y Remoción DE Puntas Figura C Montaje Y AjusteGiro DEL Cabezal DE LA Herramienta Figuras D, E AdvertenciasInterruptor Deslizable DE AVANCE/REVERSA/DESBLOQUEO FIG. F Instrucciones DE OperaciónEncendido Y Apagado FIG. G Control DE Torsión Figura HSugerencias Generales DE Taladrado TaladradoMantenimiento AccesoriosDetección DE Problemas GUADALAJARA, JAL CULIACAN, SIN MONTERREY, N.L TORREON, CoahVERACRUZ, VER PUEBLA, PUE

PD400, 90544571 specifications

The Black & Decker 90544571, PD400 is an innovative power tool designed for both amateur and professional users who demand top-notch performance and reliability. This versatile tool stands out with its robust construction and user-friendly features, making it an indispensable part of any toolkit.

One of the key features of the PD400 is its powerful motor that delivers excellent torque and speed, enabling users to tackle a wide variety of tasks with ease. Whether you're driving screws, drilling into wood, or tackling tougher materials, this tool provides the power needed for efficient operation. The ergonomic design ensures comfort during prolonged use, reducing hand fatigue and improving overall control.

The PD400 incorporates a 20-position clutch, offering precise control over drilling depths and allowing for adjustable torque settings. This feature is particularly valuable for users who want to avoid damaging materials or overdriving screws. Additionally, the dual speed control allows users to select between high and low-speed settings, providing versatility for both delicate work and heavy-duty applications.

Another highlight of the Black & Decker 90544571 is its lightweight design, which enhances portability and ease of handling. Despite its compact size, it doesn't compromise on power, making it perfect for both home improvement tasks and professional jobsites. The built-in LED work light illuminates dark or tight spaces, ensuring visibility and precision even in less-than-ideal conditions.

The PD400 comes equipped with a keyless chuck, making bit changes quick and effortless, thus enhancing productivity. For added convenience, it includes a built-in battery indicator that allows users to keep track of charge levels, ensuring that the tool is always ready to perform when required.

In terms of safety, the PD400 features an integrated brake, which stops the drill quickly when the trigger is released. This prevents accidents and provides additional peace of mind during operation. The durable construction ensures that the tool can withstand the rigors of daily use, rendering it a long-lasting investment.

In summary, the Black & Decker 90544571, PD400 is a feature-rich, reliable power tool that offers a perfect blend of power, precision, and user convenience. Its advanced technologies and thoughtful design make it an excellent choice for DIY enthusiasts and professionals alike, providing the performance required for an array of drilling and driving tasks.
Top Page Image Contents