Multiquip PS706036 Fuel Filter 500 Hours, Engine Tune-Up, Lubrication, Prevent Crush Injury

Page 42

PS7060 MULTIQUIP SAW — MAINTENANCE

Fuel Filter (500 Hours)

Replace the engine fuel filter (Figure 43) every 500 hours. Refer to your engine manual for specific details to perform this operation.

1

Figure 43. Fuel Filter Removal

Oil And Fuel Lines

Check the oil and fuel lines and connections regularly for leaks or damage. Repair or replace as necessary.

Engine Tune-Up

See your engine manual for specific information on tuning up your engine.

See the engine manual supplied with your machine for appropriate engine maintenance schedule and troubleshooting guide for problems.

At the front of the book (Page 9) there is a “Daily Pre-Operation Checklist”. Make copies of this checklist and use it on a daily basis.

Disconnect negative (ground) battery cable and secure away before attempting any service or maintenance on the saw.

Lubrication

This saw has many service-saving features, including fully enclosed oil bath lubricated Blade Shaft bearings that require no daily lubrication.

This saw has 4 grease fittings on the front axle assembly.

Grease these fittings every 125 hours of operation with a premium grade waterproof E.P. (extreme pressure) grease.

WARNING

Prevent Crush Injury!

Ensure the saw is securely placed on blocks before servicing lubrication points.

1.Front Axle Pivot Bearing

2.Hydraulic Lift Cylinder End

Figure 44. Grease Fittings

PAGE 42 — PS7060 MULTIQUIP SAW • OPERATION MANUAL — REV. #2 (06/02/08)

Image 42
Contents Models Proposition 65WARNING SILICOSIS/RESPIRATORYWARNINGS PS7060 Multiquip SAW Table of Contents PS7060 Multiquip SAW Dimensions PS7060 Multiquip SAW Specifications BF3L2011 Uncrated WeightCrated Weight Transmission PumpTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Safety Message Alert Symbols Always wear approved respiratory protectionAlways wear approved eye and hearing protection PS7060 Multiquip SAW Rules for Safe Operation SafetyDo not operate or service this Rules for Safe OperationPS7060 Multiquip SAW Rules for Safe Operation Always keep the work area well organizedDiamond Blade Safety Saw Lifting and Loading Safety Transporting Via truck/trailerNever transport the saw with the blade mounted Maintenance Safety BatteryCase the battery liquid dilute EmergenciesEngine FeaturesIntended Use Water SystemPage PS7060 Multiquip SAW Serial TAG Information Auxiliary Switch PS7060 Multiquip SAW Controls and IndicatorsSocket Connector Use to plug in optional light LeftWater FlowValve Meters water supplyBlade Wrench Light Assembly Rear Access PanelPS7060 Multiquip SAW Components Oil in crankcase PS7060 Multiquip SAW Basic Engine InformationAccelerator system Oil Fill Cap Remove to add engine oilRatio PS7060 Multiquip SAW Choosing Proper Blade SizeChoosing Proper Blade Size Engine RPM / 2000 desired BS RPM =Optimum Blade RPM Range Blade RPM vs. Surface Feet Per Minute SfpmSpecifictoolsto be Used Align flange pin through the blade into the inner flange PS7060 Multiquip SAW Installing the BladeInstalling the Blade Blade Direction of Rotation Tightening Direction Right SidePS7060 Multiquip SAW Installing the Blade 12 In .48 cm Lbs 56.7-79.4 KgRemove existing blade. See previous section Blade Guard OrderPS7060 Multiquip SAW Blade Guards Blade Guards with Standard Water SystemsConnect the water delivery hose to the Blade Guard. Figure Installing the Flange Guard PS7060 Multiquip SAW Water Delivery SystemsPS7060 Multiquip SAW SLH and Battery Stay-Level Handlebars SLHHandle fuel safely PS7060 Multiquip SAW Fueling the SAWFueling the Saw Do not smoke while refuelingCold Weather Operation PS7060 Multiquip SAW Pointer AdjustmentPointer Adjustment Draining theWater SystemSetting the Depth Indicator PS7060 Multiquip SAW RAISE-LOWER ControlsTop View Raise Lower Controls PS7060 Multiquip SAW Bladeshaft Engage System PS7060 Multiquip SAW Operation Wheel Drive SystemStarting and Stoppingthe Engine PS7060 Multiquip SAW Operation Restarting After Running Out of FuelOperating Synopsis PS7060 Multiquip SAW Loading and Transporting Avoid InjuryPS7060 Multiquip SAW Maintenance MaintenancePS7060 Multiquip SAW Maintenance Air Cleaner ComponentsChanging Engine Oil And Filter Oil Filter 125 HoursEngine Oil Filter Filter Seal Lubrication Fuel Filter 500 HoursEngine Tune-Up Prevent Crush InjuryRemove the Air Box Cover, Item D Battery/Charging SystemCooling System Refer to your engine manual for additional informationRemove lower battery retainer, Item B, Figure Replacing the BatteryRemove rear access panel Replace guards and panels prior to starting the engineBlade Shaft Drive Belt Pump Drive Belt BeltTensioner Pulley Belts and PulleysTo Stop Bladeshaft Rotation To Start Bladeshaft Rotation16 Nut Tensioner Nut Adjustment Notches Rotary BeltTensionerBlade Alignment Drive System AlignmentBlade Flange Puller Removing the Inner Blade Flange Installing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside FaceCircuit Breakers Relay, Glow Plug DelayTimer Starter Relay Maximum Cut Depth AdjustmentCircuit Breakers and Starter Relays PTO Drive Maintenance Raise-Lower SystemRaise-Lower System Troubleshooting Push-Pull Cable Neutral Safety Switch R Control Adjustment Hydraulic System MaintenanceAdjustment Nut Rod End Hydraulic Oil SystemHydraulic System Remove the oil reservoir cap to speed oil draining Long Term StorageDecommissioning Saw/Components Symptom Possible Cause Solution PS7060 Multiquip SAW Troubleshooting PS7060 Multiquip SAW Troubleshooting Blade TroubleshootingPage PS7060 Multiquip SAW Electrical Diagramto SN AF3700155 PS7060 Multiquip SAW Electrical Diagram SN AF3700156 & UP Lift Cylinder Assembly Lift PumpReservoir PS7060 Multiquip SAW Hydraulic Schematic SN AF3700156 & UP Terms and Conditions of Sale Parts Freight PolicyPage Canada Brazil United StatesMexico United Kingdom Your Local Dealer is
Related manuals
Manual 82 pages 54.16 Kb

PS706020, PS706036, PS706026 PS706030, PS706016 specifications

The Multiquip PS706026, PS706030, PS706036, and PS706020 are highly regarded in the world of portable generators, designed to offer optimum performance and reliability for various applications. These models showcase a blend of advanced technologies and user-friendly features, catering to both professional and residential needs.

One of the standout features of the Multiquip PS706 series is their robust and efficient engines, which deliver reliable power output. These generators are equipped with a powerful Honda engine, ensuring superior performance even in demanding conditions. The engines are designed to be fuel-efficient, allowing users to save on fuel costs while maximizing operational time.

Another significant aspect of the PS706 series is their electric start capability. This feature offers added convenience, enabling users to start the generator at the push of a button. Additionally, the generators are equipped with a recoil backup starter, ensuring that users have a reliable starting method in the event of an electrical failure.

The generators are built with a heavy-duty frame and are designed to withstand tough job site conditions. Their compact and portable design allows for easy transportation, making them an excellent choice for contractors, construction sites, and recreational use. The inclusion of rugged wheels and a comfortable handle ensures that moving the generator is hassle-free.

Moreover, the PS706 series showcases impressive noise-reduction technology. With a well-designed muffler system, these generators operate quietly, making them suitable for use in residential areas and during outdoor events where noise restrictions may apply.

Safety features are also paramount in the Multiquip PS706 series. They are equipped with circuit breakers to prevent overload and automatic low-oil shutdown to protect the engine from damage. This focus on safety ensures that users can operate the generators with peace of mind.

The PS706 series generators have multiple outlet options, providing versatility in power supply. Users can charge multiple devices simultaneously, thanks to the inclusion of 120V/240V receptacles and GFCI-protected outlets.

In summary, the Multiquip PS706026, PS706030, PS706036, and PS706020 generators are engineered with high-performance engines, easy starting options, and advanced safety features. Their durability, portability, and noise-reduction capabilities make them suitable for a wide range of applications, from construction to home backup power. With these models, users can expect reliable and efficient performance even in the most demanding environments.