Multiquip PS706016, PS706026 PS706030, PS706020, PS706036 Blade Alignment, Drive System Alignment

Page 47

PS7060 MULTIQUIP SAW — MAINTENANCE

Removal and Replacement

To ensure correct Blade Shaft/Wheel alignment this operation should be performed by and authorized Service Center.

Blade Alignment

Maintaining proper blade and drive system alignment will allow the saw to cut lines that are straight without much effort.Therefore the Blade Shaft Flanges MUST be equadistant to the sides of the saw, (+/- .030").See Figure 54 below where distance A must equal distance B.

The second requirement for the blade is that it MUST be square to horizontal (90o to flat surface). See Figure 54.

Drive System Alignment

In addition to Blade alignment, maintaining proper blade and drive system alignment will allow the saw to cut lines that are straight without much effort. Therefore the Front Wheels and Blade Shaft Axles MUST be at right angles to the frame edge.

In Figure 55 you see the distance "A" on the right side is shown as "A + .187"" which means that the distance between centers of the front and rear drive axles are 3/16" longer than on the opposite side. This will have the effect of causing the saw to "steer" slightly to the left. After becoming familar with the saws particular sawing characteristics, the operator may wish to have this alignment altered to fit his own preferences or to fit a particular application.

A + .187”

X

AB

90o

Figure 54. Blade Alignment Requirements

AX

Figure 55. Wheel Alignment Requirements

Drive System Alignment Adjustment

The drive wheels are aligned by adjusting the entire rear drive assembly.

1.LoosentheTransaxleAttachmentBoltsjustenoughtomove the Transaxle. Do not completely loosen the Bolts.

2.Loosen and tighten the Alignment Jackscrew nuts to move theTransaxle, and thus the wheels, in the appropriate direc- tiontoachievethedesiredalignmentdistance.(SeeFig.55)

PS7060 MULTIQUIP SAW • OPERATION MANUAL — REV. #2 (06/02/08) — PAGE 47

Image 47
Contents Models Proposition 65WARNING SILICOSIS/RESPIRATORYWARNINGS PS7060 Multiquip SAW Table of Contents PS7060 Multiquip SAW Dimensions PS7060 Multiquip SAW Specifications Transmission Pump Uncrated WeightCrated Weight BF3L2011Training Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Always wear approved eye and hearing protection Safety Message Alert SymbolsAlways wear approved respiratory protection Rules for Safe Operation SafetyDo not operate or service this PS7060 Multiquip SAW Rules for Safe OperationAlways keep the work area well organized PS7060 Multiquip SAW Rules for Safe OperationDiamond Blade Safety Never transport the saw with the blade mounted Saw Lifting and Loading SafetyTransporting Via truck/trailer Emergencies BatteryCase the battery liquid dilute Maintenance SafetyWater System FeaturesIntended Use EnginePage PS7060 Multiquip SAW Serial TAG Information LeftWater FlowValve Meters water supply PS7060 Multiquip SAW Controls and IndicatorsSocket Connector Use to plug in optional light Auxiliary SwitchPS7060 Multiquip SAW Components Blade Wrench Light AssemblyRear Access Panel Oil Fill Cap Remove to add engine oil PS7060 Multiquip SAW Basic Engine InformationAccelerator system Oil in crankcaseEngine RPM / 2000 desired BS RPM = PS7060 Multiquip SAW Choosing Proper Blade SizeChoosing Proper Blade Size RatioBlade RPM vs. Surface Feet Per Minute Sfpm Optimum Blade RPM RangeSpecifictoolsto be Used Blade Direction of Rotation Tightening Direction Right Side PS7060 Multiquip SAW Installing the BladeInstalling the Blade Align flange pin through the blade into the inner flangeRemove existing blade. See previous section PS7060 Multiquip SAW Installing the Blade12 In .48 cm Lbs 56.7-79.4 Kg Order Blade GuardConnect the water delivery hose to the Blade Guard. Figure PS7060 Multiquip SAW Blade GuardsBlade Guards with Standard Water Systems PS7060 Multiquip SAW Water Delivery Systems Installing the Flange GuardStay-Level Handlebars SLH PS7060 Multiquip SAW SLH and BatteryDo not smoke while refueling PS7060 Multiquip SAW Fueling the SAWFueling the Saw Handle fuel safelyDraining theWater System PS7060 Multiquip SAW Pointer AdjustmentPointer Adjustment Cold Weather OperationTop View Raise Lower Controls Setting the Depth IndicatorPS7060 Multiquip SAW RAISE-LOWER Controls PS7060 Multiquip SAW Bladeshaft Engage System Starting and Stoppingthe Engine PS7060 Multiquip SAW OperationWheel Drive System Operating Synopsis PS7060 Multiquip SAW OperationRestarting After Running Out of Fuel Avoid Injury PS7060 Multiquip SAW Loading and TransportingMaintenance PS7060 Multiquip SAW MaintenanceAir Cleaner Components PS7060 Multiquip SAW MaintenanceEngine Oil Filter Filter Seal Changing Engine Oil And FilterOil Filter 125 Hours Prevent Crush Injury Fuel Filter 500 HoursEngine Tune-Up LubricationRefer to your engine manual for additional information Battery/Charging SystemCooling System Remove the Air Box Cover, Item DReplace guards and panels prior to starting the engine Replacing the BatteryRemove rear access panel Remove lower battery retainer, Item B, FigureTo Start Bladeshaft Rotation Belts and PulleysTo Stop Bladeshaft Rotation Blade Shaft Drive Belt Pump Drive Belt BeltTensioner PulleyRotary BeltTensioner 16 Nut Tensioner Nut Adjustment NotchesDrive System Alignment Blade AlignmentBlade Flange Puller Removing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside Face Installing the Inner Blade FlangeCircuit Breakers and Starter Relays Circuit Breakers Relay, Glow Plug DelayTimer Starter RelayMaximum Cut Depth Adjustment Raise-Lower System PTO Drive MaintenanceRaise-Lower System Troubleshooting Hydraulic Oil System R Control Adjustment Hydraulic System MaintenanceAdjustment Nut Rod End Push-Pull Cable Neutral Safety SwitchHydraulic System Decommissioning Saw/Components Remove the oil reservoir cap to speed oil drainingLong Term Storage Symptom Possible Cause Solution PS7060 Multiquip SAW Troubleshooting Blade Troubleshooting PS7060 Multiquip SAW TroubleshootingPage PS7060 Multiquip SAW Electrical Diagramto SN AF3700155 PS7060 Multiquip SAW Electrical Diagram SN AF3700156 & UP Reservoir Lift Cylinder AssemblyLift Pump PS7060 Multiquip SAW Hydraulic Schematic SN AF3700156 & UP Freight Policy Terms and Conditions of Sale PartsPage Your Local Dealer is United StatesMexico United Kingdom Canada Brazil
Related manuals
Manual 82 pages 54.16 Kb

PS706020, PS706036, PS706026 PS706030, PS706016 specifications

The Multiquip PS706026, PS706030, PS706036, and PS706020 are highly regarded in the world of portable generators, designed to offer optimum performance and reliability for various applications. These models showcase a blend of advanced technologies and user-friendly features, catering to both professional and residential needs.

One of the standout features of the Multiquip PS706 series is their robust and efficient engines, which deliver reliable power output. These generators are equipped with a powerful Honda engine, ensuring superior performance even in demanding conditions. The engines are designed to be fuel-efficient, allowing users to save on fuel costs while maximizing operational time.

Another significant aspect of the PS706 series is their electric start capability. This feature offers added convenience, enabling users to start the generator at the push of a button. Additionally, the generators are equipped with a recoil backup starter, ensuring that users have a reliable starting method in the event of an electrical failure.

The generators are built with a heavy-duty frame and are designed to withstand tough job site conditions. Their compact and portable design allows for easy transportation, making them an excellent choice for contractors, construction sites, and recreational use. The inclusion of rugged wheels and a comfortable handle ensures that moving the generator is hassle-free.

Moreover, the PS706 series showcases impressive noise-reduction technology. With a well-designed muffler system, these generators operate quietly, making them suitable for use in residential areas and during outdoor events where noise restrictions may apply.

Safety features are also paramount in the Multiquip PS706 series. They are equipped with circuit breakers to prevent overload and automatic low-oil shutdown to protect the engine from damage. This focus on safety ensures that users can operate the generators with peace of mind.

The PS706 series generators have multiple outlet options, providing versatility in power supply. Users can charge multiple devices simultaneously, thanks to the inclusion of 120V/240V receptacles and GFCI-protected outlets.

In summary, the Multiquip PS706026, PS706030, PS706036, and PS706020 generators are engineered with high-performance engines, easy starting options, and advanced safety features. Their durability, portability, and noise-reduction capabilities make them suitable for a wide range of applications, from construction to home backup power. With these models, users can expect reliable and efficient performance even in the most demanding environments.