Multiquip PS706020, PS706026 PS706030, PS706036, PS706016 operation manual Specifictoolsto be Used

Page 25

PS7060 MULTIQUIP SAW — SPECIFIC TOOLS / SAW BLADES

SPECIFICTOOLSTO BE USED

This saw is to use tools (blades) as follows:

Steel Core Segmented or Continuous Diamond Rim Cutting Wheel.

Any other type of tool is not to be used.

WARNING

Failure to thoroughly inspect the diamond blade, (Figure 9) for operational safety could result in damage to the blade or the saw, and may cause injury to the user or others in the operating area. Discard damaged or worn blades and replace with fresh blade.

Figure 9. Diamond Blade

1.

Drive Pin Hole – A commonly located hole on the diamond

 

blade core that prevents operational blade slippage

 

between the inner & outer blade flanges (collars). Inspect

 

the diameter of the hole to ensure there is no distortion,

 

and that a snug fit develops between the hole and drive

 

pin.

2.

Stress Relief Holes (Gullets) – Check the steel core for

 

cracks that may have propagated from the slots and/or

 

gullets. Cracks indicate extreme fatigue failure and if sawing

 

continues, catastrophic failure will occur.

3.

Edge Of The Steel Core – Check the diameter edge for

 

discoloration (blue oxidation) indicating an overheating

 

condition caused by insufficient cooling water/air.

 

Overheating of blades may lead to loss of core tension

 

and/or increase the possibility for blade failure. Check to

 

make sure the steel core’s width is uniform about the rim of

 

the blade, and not succumbing to an “under cutting”

 

condition brought about by highly abrasive material or

 

improper under cutting core protection.

4. Directional Arrow – Check to ensure that the blade is oriented properly on the spindle/arbor for sawing. Reference the directional arrow on the blade and place it so the

 

direction of rotation “downcuts” with the turn of the shaft.

5.

Diamond Segment or Rim – Ensure there are no cracks,

 

dings, or missing portions of the diamond segment/rim. DO

 

NOT use a blade that is missing a segment or a portion

 

of the rim. Damaged and/or missing segments/rims may

 

cause damage to your saw, and injury to the user or others

 

in the operating area.

6.

Specifications – Ensure that the blade specifications, size,

 

and diameter properly match up to the sawing operation.

 

Wet blades must have water to act as a coolant. Utilizing a

 

diamond blade not matched properly to the task may result

 

in poor performance and/or blade damage.

7.

Arbor Hole – It is essential that the arbor hole diameter

 

properly matches the shaft arbor, and that it is free from

 

distortions. Correct blade flanges (collars) must be used.

 

The inside face of the flanges must be clean & free of debris.

 

An out of round arbor condition will cause damage to the

 

blade and the saw.

8. MAX RPM – This RPM reference is the maximum safe operating speed for the blade selected. NEVER exceed the max RPM on the diamond blade. Exceeding the MAX RPM is dangerous, and may cause poor performance and may damage the blade. All blades used must be designed for the maximum spindle RPM.

PS7060 MULTIQUIP SAW • OPERATION MANUAL — REV. #2 (06/02/08) — PAGE 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Models Proposition 65WARNING SILICOSIS/RESPIRATORYWARNINGS PS7060 Multiquip SAW Table of Contents PS7060 Multiquip SAW Dimensions PS7060 Multiquip SAW Specifications Crated Weight Uncrated WeightBF3L2011 Transmission PumpTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Always wear approved respiratory protection Safety Message Alert SymbolsAlways wear approved eye and hearing protection Do not operate or service this SafetyPS7060 Multiquip SAW Rules for Safe Operation Rules for Safe OperationAlways keep the work area well organized PS7060 Multiquip SAW Rules for Safe OperationDiamond Blade Safety Transporting Via truck/trailer Saw Lifting and Loading SafetyNever transport the saw with the blade mounted Case the battery liquid dilute BatteryMaintenance Safety EmergenciesIntended Use FeaturesEngine Water SystemPage PS7060 Multiquip SAW Serial TAG Information Socket Connector Use to plug in optional light PS7060 Multiquip SAW Controls and IndicatorsAuxiliary Switch LeftWater FlowValve Meters water supplyRear Access Panel Blade Wrench Light AssemblyPS7060 Multiquip SAW Components Accelerator system PS7060 Multiquip SAW Basic Engine InformationOil in crankcase Oil Fill Cap Remove to add engine oilChoosing Proper Blade Size PS7060 Multiquip SAW Choosing Proper Blade SizeRatio Engine RPM / 2000 desired BS RPM =Blade RPM vs. Surface Feet Per Minute Sfpm Optimum Blade RPM RangeSpecifictoolsto be Used Installing the Blade PS7060 Multiquip SAW Installing the BladeAlign flange pin through the blade into the inner flange Blade Direction of Rotation Tightening Direction Right Side12 In .48 cm Lbs 56.7-79.4 Kg PS7060 Multiquip SAW Installing the BladeRemove existing blade. See previous section Order Blade GuardBlade Guards with Standard Water Systems PS7060 Multiquip SAW Blade GuardsConnect the water delivery hose to the Blade Guard. Figure PS7060 Multiquip SAW Water Delivery Systems Installing the Flange GuardStay-Level Handlebars SLH PS7060 Multiquip SAW SLH and BatteryFueling the Saw PS7060 Multiquip SAW Fueling the SAWHandle fuel safely Do not smoke while refuelingPointer Adjustment PS7060 Multiquip SAW Pointer AdjustmentCold Weather Operation Draining theWater SystemPS7060 Multiquip SAW RAISE-LOWER Controls Setting the Depth IndicatorTop View Raise Lower Controls PS7060 Multiquip SAW Bladeshaft Engage System Wheel Drive System PS7060 Multiquip SAW OperationStarting and Stoppingthe Engine Restarting After Running Out of Fuel PS7060 Multiquip SAW OperationOperating Synopsis Avoid Injury PS7060 Multiquip SAW Loading and TransportingMaintenance PS7060 Multiquip SAW MaintenanceAir Cleaner Components PS7060 Multiquip SAW MaintenanceOil Filter 125 Hours Changing Engine Oil And FilterEngine Oil Filter Filter Seal Engine Tune-Up Fuel Filter 500 HoursLubrication Prevent Crush InjuryCooling System Battery/Charging SystemRemove the Air Box Cover, Item D Refer to your engine manual for additional informationRemove rear access panel Replacing the BatteryRemove lower battery retainer, Item B, Figure Replace guards and panels prior to starting the engineTo Stop Bladeshaft Rotation Belts and PulleysBlade Shaft Drive Belt Pump Drive Belt BeltTensioner Pulley To Start Bladeshaft RotationRotary BeltTensioner 16 Nut Tensioner Nut Adjustment NotchesDrive System Alignment Blade AlignmentBlade Flange Puller Removing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside Face Installing the Inner Blade FlangeMaximum Cut Depth Adjustment Circuit Breakers Relay, Glow Plug DelayTimer Starter RelayCircuit Breakers and Starter Relays Raise-Lower System PTO Drive MaintenanceRaise-Lower System Troubleshooting Adjustment Nut Rod End R Control Adjustment Hydraulic System MaintenancePush-Pull Cable Neutral Safety Switch Hydraulic Oil SystemHydraulic System Long Term Storage Remove the oil reservoir cap to speed oil drainingDecommissioning Saw/Components Symptom Possible Cause Solution PS7060 Multiquip SAW Troubleshooting Blade Troubleshooting PS7060 Multiquip SAW TroubleshootingPage PS7060 Multiquip SAW Electrical Diagramto SN AF3700155 PS7060 Multiquip SAW Electrical Diagram SN AF3700156 & UP Lift Pump Lift Cylinder AssemblyReservoir PS7060 Multiquip SAW Hydraulic Schematic SN AF3700156 & UP Freight Policy Terms and Conditions of Sale PartsPage Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is
Related manuals
Manual 82 pages 54.16 Kb

PS706020, PS706036, PS706026 PS706030, PS706016 specifications

The Multiquip PS706026, PS706030, PS706036, and PS706020 are highly regarded in the world of portable generators, designed to offer optimum performance and reliability for various applications. These models showcase a blend of advanced technologies and user-friendly features, catering to both professional and residential needs.

One of the standout features of the Multiquip PS706 series is their robust and efficient engines, which deliver reliable power output. These generators are equipped with a powerful Honda engine, ensuring superior performance even in demanding conditions. The engines are designed to be fuel-efficient, allowing users to save on fuel costs while maximizing operational time.

Another significant aspect of the PS706 series is their electric start capability. This feature offers added convenience, enabling users to start the generator at the push of a button. Additionally, the generators are equipped with a recoil backup starter, ensuring that users have a reliable starting method in the event of an electrical failure.

The generators are built with a heavy-duty frame and are designed to withstand tough job site conditions. Their compact and portable design allows for easy transportation, making them an excellent choice for contractors, construction sites, and recreational use. The inclusion of rugged wheels and a comfortable handle ensures that moving the generator is hassle-free.

Moreover, the PS706 series showcases impressive noise-reduction technology. With a well-designed muffler system, these generators operate quietly, making them suitable for use in residential areas and during outdoor events where noise restrictions may apply.

Safety features are also paramount in the Multiquip PS706 series. They are equipped with circuit breakers to prevent overload and automatic low-oil shutdown to protect the engine from damage. This focus on safety ensures that users can operate the generators with peace of mind.

The PS706 series generators have multiple outlet options, providing versatility in power supply. Users can charge multiple devices simultaneously, thanks to the inclusion of 120V/240V receptacles and GFCI-protected outlets.

In summary, the Multiquip PS706026, PS706030, PS706036, and PS706020 generators are engineered with high-performance engines, easy starting options, and advanced safety features. Their durability, portability, and noise-reduction capabilities make them suitable for a wide range of applications, from construction to home backup power. With these models, users can expect reliable and efficient performance even in the most demanding environments.
Top Page Image Contents