Multiquip PS706036, PS706026 PS706030 Rotary BeltTensioner, Nut Tensioner Nut Adjustment Notches

Page 46

PS7060 MULTIQUIP SAW — MAINTENANCE

Rotary BeltTensioner

The Rotary Belt Tensioner system uses a 9/16"-headed nut and a 15/16" or 1" nut to set belt tension by positioning an arm between the Tensioner Pulley and the Tensioner Base. Ridges on the Base mark the amount of tension.

Adjust to 3-1/2 notches on the tensioner:

1.Loosen the 9/16" nut.

2.Rotate the Tensioner Nut clockwise until the desired belt tension is achieved.

3.Tighten the 9/16"nut.

3

2

1

1.9/16" Nut

2.Tensioner Nut

3.Adjustment Notches

Figure 51. Tension Adjustment Notches

Blade Shaft Maintenance

The fully enclosed Blade Shaft eliminates most maintenance. Should the Blade Shaft need service or repair however, contact the manufacturer for details.

Blade Shaft Assembly

Figure 52. Blade Shaft Assembly

External Components

 

4

5

 

 

1

 

6

2

7

3

 

 

 

5

 

 

3

 

7

 

 

 

2

 

 

6

1.

Bolt, 5/8 GR8

1

 

2.

Bushing

4

 

3.Outer Flange

4.Inner Flange

5.Drive Key

6.Bladeshaft

7.Bladeshaft Housing

Figure 53. Blade Shaft External Components

PAGE 46 — PS7060 MULTIQUIP SAW • OPERATION MANUAL — REV. #2 (06/02/08)

Image 46
Contents Models Proposition 65WARNING SILICOSIS/RESPIRATORYWARNINGS PS7060 Multiquip SAW Table of Contents PS7060 Multiquip SAW Dimensions PS7060 Multiquip SAW Specifications BF3L2011 Uncrated WeightCrated Weight Transmission PumpTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Always wear approved respiratory protection Safety Message Alert SymbolsAlways wear approved eye and hearing protection PS7060 Multiquip SAW Rules for Safe Operation SafetyDo not operate or service this Rules for Safe OperationPS7060 Multiquip SAW Rules for Safe Operation Always keep the work area well organizedDiamond Blade Safety Transporting Via truck/trailer Saw Lifting and Loading SafetyNever transport the saw with the blade mounted Maintenance Safety BatteryCase the battery liquid dilute EmergenciesEngine FeaturesIntended Use Water SystemPage PS7060 Multiquip SAW Serial TAG Information Auxiliary Switch PS7060 Multiquip SAW Controls and IndicatorsSocket Connector Use to plug in optional light LeftWater FlowValve Meters water supplyRear Access Panel Blade Wrench Light AssemblyPS7060 Multiquip SAW Components Oil in crankcase PS7060 Multiquip SAW Basic Engine InformationAccelerator system Oil Fill Cap Remove to add engine oilRatio PS7060 Multiquip SAW Choosing Proper Blade SizeChoosing Proper Blade Size Engine RPM / 2000 desired BS RPM =Optimum Blade RPM Range Blade RPM vs. Surface Feet Per Minute SfpmSpecifictoolsto be Used Align flange pin through the blade into the inner flange PS7060 Multiquip SAW Installing the BladeInstalling the Blade Blade Direction of Rotation Tightening Direction Right Side12 In .48 cm Lbs 56.7-79.4 Kg PS7060 Multiquip SAW Installing the BladeRemove existing blade. See previous section Blade Guard OrderBlade Guards with Standard Water Systems PS7060 Multiquip SAW Blade GuardsConnect the water delivery hose to the Blade Guard. Figure Installing the Flange Guard PS7060 Multiquip SAW Water Delivery SystemsPS7060 Multiquip SAW SLH and Battery Stay-Level Handlebars SLHHandle fuel safely PS7060 Multiquip SAW Fueling the SAWFueling the Saw Do not smoke while refuelingCold Weather Operation PS7060 Multiquip SAW Pointer AdjustmentPointer Adjustment Draining theWater SystemPS7060 Multiquip SAW RAISE-LOWER Controls Setting the Depth IndicatorTop View Raise Lower Controls PS7060 Multiquip SAW Bladeshaft Engage System Wheel Drive System PS7060 Multiquip SAW OperationStarting and Stoppingthe Engine Restarting After Running Out of Fuel PS7060 Multiquip SAW OperationOperating Synopsis PS7060 Multiquip SAW Loading and Transporting Avoid InjuryPS7060 Multiquip SAW Maintenance MaintenancePS7060 Multiquip SAW Maintenance Air Cleaner ComponentsOil Filter 125 Hours Changing Engine Oil And FilterEngine Oil Filter Filter Seal Lubrication Fuel Filter 500 HoursEngine Tune-Up Prevent Crush InjuryRemove the Air Box Cover, Item D Battery/Charging SystemCooling System Refer to your engine manual for additional informationRemove lower battery retainer, Item B, Figure Replacing the BatteryRemove rear access panel Replace guards and panels prior to starting the engineBlade Shaft Drive Belt Pump Drive Belt BeltTensioner Pulley Belts and PulleysTo Stop Bladeshaft Rotation To Start Bladeshaft Rotation16 Nut Tensioner Nut Adjustment Notches Rotary BeltTensionerBlade Alignment Drive System AlignmentBlade Flange Puller Removing the Inner Blade Flange Installing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside FaceMaximum Cut Depth Adjustment Circuit Breakers Relay, Glow Plug DelayTimer Starter RelayCircuit Breakers and Starter Relays PTO Drive Maintenance Raise-Lower SystemRaise-Lower System Troubleshooting Push-Pull Cable Neutral Safety Switch R Control Adjustment Hydraulic System MaintenanceAdjustment Nut Rod End Hydraulic Oil SystemHydraulic System Long Term Storage Remove the oil reservoir cap to speed oil drainingDecommissioning Saw/Components Symptom Possible Cause Solution PS7060 Multiquip SAW Troubleshooting PS7060 Multiquip SAW Troubleshooting Blade TroubleshootingPage PS7060 Multiquip SAW Electrical Diagramto SN AF3700155 PS7060 Multiquip SAW Electrical Diagram SN AF3700156 & UP Lift Pump Lift Cylinder AssemblyReservoir PS7060 Multiquip SAW Hydraulic Schematic SN AF3700156 & UP Terms and Conditions of Sale Parts Freight PolicyPage Canada Brazil United StatesMexico United Kingdom Your Local Dealer is
Related manuals
Manual 82 pages 54.16 Kb

PS706020, PS706036, PS706026 PS706030, PS706016 specifications

The Multiquip PS706026, PS706030, PS706036, and PS706020 are highly regarded in the world of portable generators, designed to offer optimum performance and reliability for various applications. These models showcase a blend of advanced technologies and user-friendly features, catering to both professional and residential needs.

One of the standout features of the Multiquip PS706 series is their robust and efficient engines, which deliver reliable power output. These generators are equipped with a powerful Honda engine, ensuring superior performance even in demanding conditions. The engines are designed to be fuel-efficient, allowing users to save on fuel costs while maximizing operational time.

Another significant aspect of the PS706 series is their electric start capability. This feature offers added convenience, enabling users to start the generator at the push of a button. Additionally, the generators are equipped with a recoil backup starter, ensuring that users have a reliable starting method in the event of an electrical failure.

The generators are built with a heavy-duty frame and are designed to withstand tough job site conditions. Their compact and portable design allows for easy transportation, making them an excellent choice for contractors, construction sites, and recreational use. The inclusion of rugged wheels and a comfortable handle ensures that moving the generator is hassle-free.

Moreover, the PS706 series showcases impressive noise-reduction technology. With a well-designed muffler system, these generators operate quietly, making them suitable for use in residential areas and during outdoor events where noise restrictions may apply.

Safety features are also paramount in the Multiquip PS706 series. They are equipped with circuit breakers to prevent overload and automatic low-oil shutdown to protect the engine from damage. This focus on safety ensures that users can operate the generators with peace of mind.

The PS706 series generators have multiple outlet options, providing versatility in power supply. Users can charge multiple devices simultaneously, thanks to the inclusion of 120V/240V receptacles and GFCI-protected outlets.

In summary, the Multiquip PS706026, PS706030, PS706036, and PS706020 generators are engineered with high-performance engines, easy starting options, and advanced safety features. Their durability, portability, and noise-reduction capabilities make them suitable for a wide range of applications, from construction to home backup power. With these models, users can expect reliable and efficient performance even in the most demanding environments.