Multiquip PS706020, PS706036 PS7060 Multiquip SAW Operation, Restarting After Running Out of Fuel

Page 37

PS7060 MULTIQUIP SAW — OPERATION

8.Allow the engine to warm up for several minutes.

9.Set the throttle to the recommended engine RPM to match the recommended blade speed of the attached blade.

10.Lower the blade to the cut depth.

11.Move the control handle FORWARD to advance the cut.

Stopping the Engine

In case of an EMERGENCY, push the RED EMERGENCY-STOP BUTTON to stop all functions. (Figure 35.) Engine will not crank when emergency stop button is depressed.

Figure 35. Emergency Stop Button

1.When finished with the cut, move the control handle to the NEUTRAL position.

2.Raise the saw blade out of the cut.

3.Reduce the throttle to idle.

4.Allow the engine to run one or two minutes to let the engine cool down.

5.To stop the engine, turn the Ignition Switch to the OFF position.

Restarting After Running Out of Fuel

The 2011 series Deutz engines do not require bleeding of the fuel system if the engine is run out of fuel.

To restart the engine:

1.Re-fill the fuel tank with fresh, clean diesel fuel.

2.Units up to S/N ZC3700225 only: Re-prime the fuel system by squeezing the fuel prime bulb (located inside the console, directly under the fuel tank), until the fuel primer bulb will becomes firm.

3.Crank the engine normally until it starts.

Operating Synopsis

BEFORE STARTING – Check all fluid levels.Secure blade firmly to bladeshaft. Make sure all protective guards are in place and properly mounted. Wear eye, ear protection and protective clothing.

WATER SUPPLY – Connect water supply to water inlet. Move water ON/OFF CONTROL to ON position. Adjust WATER FLOW CONTROL lever to desired position. Drain watering system in cold weather to prevent damage due to freezing.

BLADES – Always follow blade manufacturer's recommendations for blade selection, speed and application. NEVER exceed blade manufacturer's maximum rated RPM. See previous steps for detailed blade mounting instructions.

STARTING ENGINE – Set CONTROL HANDLE to NEUTRAL position. Set THROTTLE to IDLE.Turn start switch to ON position. Wait for glow plug indicator light to go out. Momentarily turn switch to start position; release switch as soon as engine starts. Allow engine to warm up for several minutes before increasing engine speed. Use approved diesel fuel only.

STOPPING ENGINE – Do not stop engine abruptly when hot! Reduce THROTTLE to IDLE and allow engine to run 1 to 2 minutes before turning ignition switch off. Damage to engine may occur if not allowed to cool adequately.

FWD-NEUTRAL-REV CONTROL – The panel mounted handle controls FORWARD, NEUTRAL AND REVERSE operation. Neutral position stops or holds saw in a stationary position. Incremental movement in the FORWARD or REVERSE direction will increase speed proportionate to amount of movement.

RAISE-LOWER FUNCTION – RAISE-LOWER function is controlled by the switch mounted at the right side of the CONTROL HANDLE. Push toggle switch lever forward to lower saw. Pull toggle switch lever backward to raise saw.

BRAKES – This saw is equipped with parking brakes. Brakes are applied automatically when engine is off and dis- engaged when engine is running.

PS7060 MULTIQUIP SAW • OPERATION MANUAL — REV. #2 (06/02/08) — PAGE 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Models Proposition 65WARNING SILICOSIS/RESPIRATORYWARNINGS PS7060 Multiquip SAW Table of Contents PS7060 Multiquip SAW Dimensions PS7060 Multiquip SAW Specifications Crated Weight Uncrated WeightBF3L2011 Transmission PumpTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Always wear approved respiratory protection Safety Message Alert SymbolsAlways wear approved eye and hearing protection Do not operate or service this SafetyPS7060 Multiquip SAW Rules for Safe Operation Rules for Safe OperationAlways keep the work area well organized PS7060 Multiquip SAW Rules for Safe OperationDiamond Blade Safety Transporting Via truck/trailer Saw Lifting and Loading SafetyNever transport the saw with the blade mounted Case the battery liquid dilute BatteryMaintenance Safety EmergenciesIntended Use FeaturesEngine Water SystemPage PS7060 Multiquip SAW Serial TAG Information Socket Connector Use to plug in optional light PS7060 Multiquip SAW Controls and IndicatorsAuxiliary Switch LeftWater FlowValve Meters water supplyRear Access Panel Blade Wrench Light AssemblyPS7060 Multiquip SAW Components Accelerator system PS7060 Multiquip SAW Basic Engine InformationOil in crankcase Oil Fill Cap Remove to add engine oilChoosing Proper Blade Size PS7060 Multiquip SAW Choosing Proper Blade SizeRatio Engine RPM / 2000 desired BS RPM =Blade RPM vs. Surface Feet Per Minute Sfpm Optimum Blade RPM RangeSpecifictoolsto be Used Installing the Blade PS7060 Multiquip SAW Installing the BladeAlign flange pin through the blade into the inner flange Blade Direction of Rotation Tightening Direction Right Side12 In .48 cm Lbs 56.7-79.4 Kg PS7060 Multiquip SAW Installing the BladeRemove existing blade. See previous section Order Blade GuardBlade Guards with Standard Water Systems PS7060 Multiquip SAW Blade GuardsConnect the water delivery hose to the Blade Guard. Figure PS7060 Multiquip SAW Water Delivery Systems Installing the Flange GuardStay-Level Handlebars SLH PS7060 Multiquip SAW SLH and BatteryFueling the Saw PS7060 Multiquip SAW Fueling the SAWHandle fuel safely Do not smoke while refuelingPointer Adjustment PS7060 Multiquip SAW Pointer AdjustmentCold Weather Operation Draining theWater SystemPS7060 Multiquip SAW RAISE-LOWER Controls Setting the Depth IndicatorTop View Raise Lower Controls PS7060 Multiquip SAW Bladeshaft Engage System Wheel Drive System PS7060 Multiquip SAW OperationStarting and Stoppingthe Engine Restarting After Running Out of Fuel PS7060 Multiquip SAW OperationOperating Synopsis Avoid Injury PS7060 Multiquip SAW Loading and TransportingMaintenance PS7060 Multiquip SAW MaintenanceAir Cleaner Components PS7060 Multiquip SAW MaintenanceOil Filter 125 Hours Changing Engine Oil And FilterEngine Oil Filter Filter Seal Engine Tune-Up Fuel Filter 500 HoursLubrication Prevent Crush InjuryCooling System Battery/Charging SystemRemove the Air Box Cover, Item D Refer to your engine manual for additional informationRemove rear access panel Replacing the BatteryRemove lower battery retainer, Item B, Figure Replace guards and panels prior to starting the engineTo Stop Bladeshaft Rotation Belts and PulleysBlade Shaft Drive Belt Pump Drive Belt BeltTensioner Pulley To Start Bladeshaft RotationRotary BeltTensioner 16 Nut Tensioner Nut Adjustment NotchesDrive System Alignment Blade AlignmentBlade Flange Puller Removing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside Face Installing the Inner Blade FlangeMaximum Cut Depth Adjustment Circuit Breakers Relay, Glow Plug DelayTimer Starter RelayCircuit Breakers and Starter Relays Raise-Lower System PTO Drive MaintenanceRaise-Lower System Troubleshooting Adjustment Nut Rod End R Control Adjustment Hydraulic System MaintenancePush-Pull Cable Neutral Safety Switch Hydraulic Oil SystemHydraulic System Long Term Storage Remove the oil reservoir cap to speed oil drainingDecommissioning Saw/Components Symptom Possible Cause Solution PS7060 Multiquip SAW Troubleshooting Blade Troubleshooting PS7060 Multiquip SAW TroubleshootingPage PS7060 Multiquip SAW Electrical Diagramto SN AF3700155 PS7060 Multiquip SAW Electrical Diagram SN AF3700156 & UP Lift Pump Lift Cylinder AssemblyReservoir PS7060 Multiquip SAW Hydraulic Schematic SN AF3700156 & UP Freight Policy Terms and Conditions of Sale PartsPage Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is
Related manuals
Manual 82 pages 54.16 Kb

PS706020, PS706036, PS706026 PS706030, PS706016 specifications

The Multiquip PS706026, PS706030, PS706036, and PS706020 are highly regarded in the world of portable generators, designed to offer optimum performance and reliability for various applications. These models showcase a blend of advanced technologies and user-friendly features, catering to both professional and residential needs.

One of the standout features of the Multiquip PS706 series is their robust and efficient engines, which deliver reliable power output. These generators are equipped with a powerful Honda engine, ensuring superior performance even in demanding conditions. The engines are designed to be fuel-efficient, allowing users to save on fuel costs while maximizing operational time.

Another significant aspect of the PS706 series is their electric start capability. This feature offers added convenience, enabling users to start the generator at the push of a button. Additionally, the generators are equipped with a recoil backup starter, ensuring that users have a reliable starting method in the event of an electrical failure.

The generators are built with a heavy-duty frame and are designed to withstand tough job site conditions. Their compact and portable design allows for easy transportation, making them an excellent choice for contractors, construction sites, and recreational use. The inclusion of rugged wheels and a comfortable handle ensures that moving the generator is hassle-free.

Moreover, the PS706 series showcases impressive noise-reduction technology. With a well-designed muffler system, these generators operate quietly, making them suitable for use in residential areas and during outdoor events where noise restrictions may apply.

Safety features are also paramount in the Multiquip PS706 series. They are equipped with circuit breakers to prevent overload and automatic low-oil shutdown to protect the engine from damage. This focus on safety ensures that users can operate the generators with peace of mind.

The PS706 series generators have multiple outlet options, providing versatility in power supply. Users can charge multiple devices simultaneously, thanks to the inclusion of 120V/240V receptacles and GFCI-protected outlets.

In summary, the Multiquip PS706026, PS706030, PS706036, and PS706020 generators are engineered with high-performance engines, easy starting options, and advanced safety features. Their durability, portability, and noise-reduction capabilities make them suitable for a wide range of applications, from construction to home backup power. With these models, users can expect reliable and efficient performance even in the most demanding environments.
Top Page Image Contents