Sanyo 8.53E+13 installation instructions Installation Instructions, Contents

Page 1

05-423 KHS0971-1271 12/13/05 1:23 PM Page a

INSTALLATION INSTRUCTIONS

– Inverter Split System Air Conditioner – COOL/DRY/HEAT Model

This air conditioner uses the new refrigerant R410A.

Contents

 

 

 

Page

IMPORTANT!

 

Please Read Before Starting

2

1.

GENERAL

3

 

1-1.

Tools Required for Installation (not supplied)

 

1-2.

Accessories Supplied with Unit

 

 

1-3.

Optional Copper Tubing Kit

 

 

1-4.

Type of Copper Tube and Insulation Material

 

1-5.

Additional Materials Required for Installation

2.

INSTALLATION SITE SELECTION

4

 

2-1.

Indoor Unit

 

 

2-2.

Outdoor Unit

 

3. HOW TO INSTALL THE INDOOR UNIT

6

 

3-1.

Remove the Rear Panel from the Unit

 

 

3-2.

Make a Hole

 

 

3-3.

Install the Rear Panel on the Wall

 

 

3-4.

Remove the Grille to Install the Indoor Unit

 

3-5.

Shape the Indoor Side Tubing

 

 

3-6.

Wiring Instructions

 

 

3-7.

Recommended Wire Length and Diameter

 

3-8.

Wiring Instructions for Inter-unit Connections

 

3-9.

Mounting

 

 

3-10.

Drain Hose

 

4. HOW TO INSTALL THE OUTDOOR UNIT

16

 

4-1.

Wiring Instructions for the Outdoor Unit

 

5.

REFRIGERANT TUBING

17

 

5-1.

Use of the Flaring Method

 

 

5-2.

Flaring Procedure with a Flare Tool

 

 

5-3.

Caution before Connecting Tubes Tightly

 

 

5-4.

Connecting Tubing between Indoor and

 

 

 

Outdoor Units

 

 

5-5.

Insulation of Refrigerant Tubing

 

 

5-6.

Taping the Tubes

 

 

5-7.

Finishing the Installation

 

Model Combinations

Combine indoor and outdoor units only as listed below.

Indoor Unit

Outdoor Unit

KHS0971CH0971

KHS1271CH1271

Power Source:

60 Hz, single-phase, 115 V

Be sure to read the yellow instruction sheet attached to the outdoor unit for models using the new refrigerant R410A.

7.REMOTE CONTROL UNIT INSTALLATION

POSITION

23

7-1.

Mounting on a Wall

 

8. ADDRESS SWITCH

24

8-1.

Address Setting of the Remote

 

 

Control Unit

 

NOTE

The illustrations are based on the typical appearance of

6. AIR PURGING

19

Air Purging with a Vacuum Pump (for Test Run)

Basic Functions of the Service Valves

Pump Down

a standard model. Consequently, the shape may differ from that of the air conditioner that you are installing.

In Canada

 

SANYO FISHER COMPANY

SANYO Canada Inc.

 

A DIVISION OF SANYO NORTH AMERICA CORPORATION

300 Applewood Crescent, Concord

 

21605 Plummer Street

Ontario, L4K 5C7, Canada

85264189990003 © SANYO 2006

Chatsworth, CA 91311 U.S.A.

 

W

Image 1
Contents Contents Installation Instructions…In a Ceiling or Wall For safe installation and trouble-free operation, you must…In a Room …In Moist or Uneven LocationsAccessories Supplied with Unit Table Tools Required for Installation not suppliedGeneral Optional Copper Tubing KitAdditional Materials Required for Installation Installation Site SelectionIndoor Unit Front ViewSolid base must not cover Outdoor UnitHole of the bottom plate Trical wiring or conduits are How to Install the Indoor UnitRemove the Rear Panel from the Unit Make a HoleIf Wooden Wall Install the Rear Panel on the WallIf Block, Brick, Concrete or Similar Type Wall Hole DiaHow to replace the grille Remove the Grille to Install the Indoor UnitShape the Indoor Side Tubing Wiring Instructions General precautions on wiringRecommended Wire Length and Diameter Wiring Instructions for Inter-unit Connections For Outdoor Unit For solid core wiring or F-cable How to connect wiring to the terminal For Indoor UnitFor stranded wiring Right-side tubing MountingLeft-side tubing Switching drain hose and drain capDrain hose Drain capTubing and wiring to the out Do not supply power toTo unmount indoor unit Unit or operate it until allWiring Instructions for the Outdoor Unit How to Install the Outdoor UnitTo 0.5 mm Adjust so that the amount of tube Flaring Procedure with a Flare ToolRefrigerant Tubing Use of the Flaring MethodFinishing the Installation Connecting Tubing between Indoor and Outdoor UnitsInsulation of Refrigerant Tubing Tube Dia Tightening TorqueAir Purging Hex wrench before Be sure to completely insertAttempting to turn the valve Operation lamp Timer lamp Quiet lamp ION lamp How to Test Run the Air ConditionerPump Down Basic Functions of the Service ValvesTo take out the remote control unit, pull it forward Remote Control Unit Installation PositionMounting on a Wall Address Setting of the Remote Control Unit Address Switch

8.53E+13 specifications

Sanyo 8.53E+13 is a remarkable product that stands out in the world of consumer electronics, showcasing a blend of advanced technology and innovative features. This impressive device is primarily a part of Sanyo's extensive lineup of high-capacity batteries, known for their reliability and longevity.

One of the standout features of the Sanyo 8.53E+13 is its superior energy density. With a capacity of approximately 8.53E+13 mAh, this battery is designed to provide extended usage times for electronic devices, making it an ideal choice for both personal and professional applications. Users can expect longer performance periods without the need for frequent recharging, which is a significant advantage in today's fast-paced lifestyle.

The Sanyo 8.53E+13 employs advanced lithium-ion technology that enhances its performance and safety. This technology not only allows for rapid charging but also minimizes the chances of overheating and battery degradation over time. The lithium-ion cells are engineered to deliver consistent power output, ensuring that devices powered by this battery deliver peak performance throughout their operating times.

Another key characteristic of the Sanyo 8.53E+13 is its robust design. Built to withstand varying environmental conditions, this battery is resistant to extreme temperatures and impact, making it suitable for outdoor activities and rugged usage. Its durability ensures a longer lifespan, which is an essential consideration for users who rely on their devices in demanding situations.

The Sanyo 8.53E+13 also prioritizes environmental sustainability. Sanyo has adopted eco-friendly practices in the manufacturing process of their batteries, focusing on reducing waste and promoting recycling. This commitment to sustainability is increasingly important to consumers who are looking for products that align with their environmental values.

In terms of compatibility, the Sanyo 8.53E+13 is versatile and can be used in various applications, from portable electronics to electric vehicles. Its adaptability makes it a sought-after choice among manufacturers and consumers alike, who require a dependable power source.

Overall, the Sanyo 8.53E+13 exemplifies the innovative spirit of Sanyo, combining cutting-edge technologies with practical features that meet the needs of modern users. Its energy efficiency, safety, durability, and commitment to the environment position it as a leading option in the battery market, making it an essential component for powering the devices of the future.