Sanyo 8.53E+13 To unmount indoor unit, Do not supply power to, Unit or operate it until all

Page 15

05-423 KHS0971-1271 12/13/05 1:23 PM Page 15

To unmount indoor unit

Press the 2 marks on the lower part of the indoor unit and unlatch the tabs. Then lift the indoor unit and unmount. (Fig. 42)

3-10. Drain Hose

a)The drain hose should be slanted downward to the outdoors. (Fig. 43)

b)Never form a trap in the course of the hose.

c)If the drain hose will run in the room, insulate the hose with insulation* so that chilled condensation will not damage furniture or floors. (Fig. 44)

*Foamed polyethylene or its equivalent is recom- mended.

WARNING

Do not supply power to the

 

unit or operate it until all

 

tubing and wiring to the out-

 

side unit are completed.

Risk of Electric Shock

Push

Fig. 42

 

Slant

Indoor

Drain

unit

hose

 

Fig. 43

Condensation

Insulation material (Locally purchased) must be used.

Fig. 44

15

Image 15
Contents Contents Installation Instructions…In Moist or Uneven Locations For safe installation and trouble-free operation, you must…In a Ceiling or Wall …In a RoomOptional Copper Tubing Kit Tools Required for Installation not suppliedAccessories Supplied with Unit Table GeneralFront View Installation Site SelectionAdditional Materials Required for Installation Indoor UnitOutdoor Unit Solid base must not coverHole of the bottom plate Make a Hole How to Install the Indoor UnitTrical wiring or conduits are Remove the Rear Panel from the UnitHole Dia Install the Rear Panel on the WallIf Wooden Wall If Block, Brick, Concrete or Similar Type WallHow to replace the grille Remove the Grille to Install the Indoor UnitShape the Indoor Side Tubing Wiring Instructions General precautions on wiringRecommended Wire Length and Diameter Wiring Instructions for Inter-unit Connections How to connect wiring to the terminal For Indoor Unit For Outdoor Unit For solid core wiring or F-cableFor stranded wiring Right-side tubing MountingDrain cap Switching drain hose and drain capLeft-side tubing Drain hoseUnit or operate it until all Do not supply power toTubing and wiring to the out To unmount indoor unitWiring Instructions for the Outdoor Unit How to Install the Outdoor UnitUse of the Flaring Method Flaring Procedure with a Flare ToolTo 0.5 mm Adjust so that the amount of tube Refrigerant TubingTube Dia Tightening Torque Connecting Tubing between Indoor and Outdoor UnitsFinishing the Installation Insulation of Refrigerant TubingAir Purging Be sure to completely insert Hex wrench beforeAttempting to turn the valve Operation lamp Timer lamp Quiet lamp ION lamp How to Test Run the Air ConditionerPump Down Basic Functions of the Service ValvesRemote Control Unit Installation Position To take out the remote control unit, pull it forwardMounting on a Wall Address Setting of the Remote Control Unit Address Switch

8.53E+13 specifications

Sanyo 8.53E+13 is a remarkable product that stands out in the world of consumer electronics, showcasing a blend of advanced technology and innovative features. This impressive device is primarily a part of Sanyo's extensive lineup of high-capacity batteries, known for their reliability and longevity.

One of the standout features of the Sanyo 8.53E+13 is its superior energy density. With a capacity of approximately 8.53E+13 mAh, this battery is designed to provide extended usage times for electronic devices, making it an ideal choice for both personal and professional applications. Users can expect longer performance periods without the need for frequent recharging, which is a significant advantage in today's fast-paced lifestyle.

The Sanyo 8.53E+13 employs advanced lithium-ion technology that enhances its performance and safety. This technology not only allows for rapid charging but also minimizes the chances of overheating and battery degradation over time. The lithium-ion cells are engineered to deliver consistent power output, ensuring that devices powered by this battery deliver peak performance throughout their operating times.

Another key characteristic of the Sanyo 8.53E+13 is its robust design. Built to withstand varying environmental conditions, this battery is resistant to extreme temperatures and impact, making it suitable for outdoor activities and rugged usage. Its durability ensures a longer lifespan, which is an essential consideration for users who rely on their devices in demanding situations.

The Sanyo 8.53E+13 also prioritizes environmental sustainability. Sanyo has adopted eco-friendly practices in the manufacturing process of their batteries, focusing on reducing waste and promoting recycling. This commitment to sustainability is increasingly important to consumers who are looking for products that align with their environmental values.

In terms of compatibility, the Sanyo 8.53E+13 is versatile and can be used in various applications, from portable electronics to electric vehicles. Its adaptability makes it a sought-after choice among manufacturers and consumers alike, who require a dependable power source.

Overall, the Sanyo 8.53E+13 exemplifies the innovative spirit of Sanyo, combining cutting-edge technologies with practical features that meet the needs of modern users. Its energy efficiency, safety, durability, and commitment to the environment position it as a leading option in the battery market, making it an essential component for powering the devices of the future.