…In a Ceiling or Wall, …In a Room | Sanyo 8.53E+13 specification

05-423 KHS0971-1271 12/13/05 1:23 PM Page 2

IMPORTANT!

Please Read Before Starting

This air conditioning system meets strict safety and operating standards. As the installer or service person, it is an important part of your job to install or service the system so it operates safely and efficiently.

For safe installation and trouble-free operation, you must:

●Carefully read this instruction booklet before beginning.

●Follow each installation or repair step exactly as shown.

●Observe all local, state, and national electrical codes.

●Pay close attention to all warning and caution notices given in this manual.

This symbol refers to a hazard

or unsafe practice which can WARNING result in severe personal injury

or death.

This symbol refers to a hazard or unsafe practice which can

CAUTION result in personal injury or prod- uct or property damage.

If Necessary, Get Help

These instructions are all you need for most installation sites and maintenance conditions. If you require help for a special problem, contact our sales/service outlet or your certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for improp- er installation or maintenance service, including failure to follow the instructions in this document.

SPECIAL PRECAUTIONS

WARNING	When Wiring

ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH. ONLY A QUALIFIED, EXPERIENCED ELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM.

•Do not supply power to the unit until all wiring and tubing are completed or reconnected and checked.

•Highly dangerous electrical voltages are used in this system. Carefully refer to the wiring diagram and these instructions when wiring. Improper connections and inadequate grounding can cause accidental injury or death.

•Ground the unit following local electrical codes.

•Connect all wiring tightly. Loose wiring may cause over- heating at connection points and a possible fire hazard.

When Transporting

Be careful when picking up and moving the indoor and out- door units. Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin alu- minum fins on the air conditioner can cut your fingers.

When Installing…

…In a Ceiling or Wall

Make sure the ceiling/wall is strong enough to hold the unit’s weight. It may be necessary to construct a strong wood or metal frame to provide added support.

…In a Room

Properly insulate any tubing run inside a room to prevent “sweating” that can cause dripping and water damage to walls and floors.

…In Moist or Uneven Locations

Use a raised concrete pad or concrete blocks to provide a solid, level foundation for the outdoor unit. This prevents water damage and abnormal vibration.

…In an Area with High Winds

Securely anchor the outdoor unit down with bolts and a metal frame. Provide a suitable air baffle.

…In a Snowy Area (for Heat Pump-type Systems)

Install the outdoor unit on a raised platform that is higher than drifting snow. Provide snow vents.

When Connecting Refrigerant Tubing

•Use the flare method for connecting tubing.

•Apply refrigerant lubricant to the matching surfaces of the flare and union tubes before connecting them, then tighten the nut with a torque wrench for a leak-free connection.

•Check carefully for leaks before starting the test run.

When Servicing

•Turn the power OFF at the main power box (mains) before opening the unit to check or repair electrical parts and wiring.

•Keep your fingers and clothing away from any moving parts.

•Clean up the site after you finish, remembering to check that no metal scraps or bits of wiring have been left inside the unit being serviced.

Others

CAUTION

•Ventilate any enclosed areas when installing or testing the refrigeration system. Escaped refrigerant gas, on contact with fire or heat, can produce dangerously toxic gas.

•Confirm upon completing installation that no refrigerant gas is leaking. If escaped gas comes in contact with a stove, gas water heater, electric room heater or other heat source, it can produce dangerously toxic gas.

8.53E+13 specifications

Sanyo 8.53E+13 is a remarkable product that stands out in the world of consumer electronics, showcasing a blend of advanced technology and innovative features. This impressive device is primarily a part of Sanyo's extensive lineup of high-capacity batteries, known for their reliability and longevity.

One of the standout features of the Sanyo 8.53E+13 is its superior energy density. With a capacity of approximately 8.53E+13 mAh, this battery is designed to provide extended usage times for electronic devices, making it an ideal choice for both personal and professional applications. Users can expect longer performance periods without the need for frequent recharging, which is a significant advantage in today's fast-paced lifestyle.

The Sanyo 8.53E+13 employs advanced lithium-ion technology that enhances its performance and safety. This technology not only allows for rapid charging but also minimizes the chances of overheating and battery degradation over time. The lithium-ion cells are engineered to deliver consistent power output, ensuring that devices powered by this battery deliver peak performance throughout their operating times.

Another key characteristic of the Sanyo 8.53E+13 is its robust design. Built to withstand varying environmental conditions, this battery is resistant to extreme temperatures and impact, making it suitable for outdoor activities and rugged usage. Its durability ensures a longer lifespan, which is an essential consideration for users who rely on their devices in demanding situations.

The Sanyo 8.53E+13 also prioritizes environmental sustainability. Sanyo has adopted eco-friendly practices in the manufacturing process of their batteries, focusing on reducing waste and promoting recycling. This commitment to sustainability is increasingly important to consumers who are looking for products that align with their environmental values.

In terms of compatibility, the Sanyo 8.53E+13 is versatile and can be used in various applications, from portable electronics to electric vehicles. Its adaptability makes it a sought-after choice among manufacturers and consumers alike, who require a dependable power source.

Overall, the Sanyo 8.53E+13 exemplifies the innovative spirit of Sanyo, combining cutting-edge technologies with practical features that meet the needs of modern users. Its energy efficiency, safety, durability, and commitment to the environment position it as a leading option in the battery market, making it an essential component for powering the devices of the future.